Used Pocket Hole for sale (4,214)

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Technical details turning diameter 570 mm turning length 1000 mm control MANUALplus 620 swing diameter over face slide 340 mm spindle bore 93 mm spindle turning speed range 1 - 3000 U/min transmission ratio 2 rapid power traverse in X-and Z direction 7 / 10 m/min max. workpiece weight -without tailstock 500 kg max. workpiece weight between centres 1000 kg workpiece weight in steadies max. 1250 kg main drive motor (100/60% ED) 20 / 25 kW Dimensions (LxWxH) 2,94 x 2,20 x 1,96 m max. torque on the spindle ca. 1400 Nm Iedjz Ixz Depfx Anioih weight of the machine ca. 3,4 t Additional information * HEIDENHAIN MANUALplus 620 control system - Control system expansion for ICP and DIN programs, incl. thread repair * Automatic 8-station SAUTER turret with driven stations, VDI shank D=30 mm, mounted in front of the turning center (limits achievable turning diameter and tailstock operations; reduces turning length) * 2-speed planetary gearbox, automatic shifting * Main spindle holding brake, incl. software upgrade for bolt hole circle and milling cycle options - C-axis-style functionality for pocket milling, with drilling, milling, and engraving cycles and free ICP input * Reinforced coolant pump * RÖHM 3-jaw chuck, 315 mm, with one set of hard jaws * Steady rest * Approx. 20 fixed tool holders

Condition: used, Year of construction: 2016, operating hours: 5,000 h, functionality: fully functional, machine/vehicle number: -, overall weight: 1,000 kg, total length: 3,500 mm, total width: 500 mm, total height: 1,200 mm, input voltage: 400 V, type of input current: three-phase, cutting speed: 50 mm/min, The Oddy Novatek 2 Pocket Roll Plant with Pinner is used to automatically divide, round, shape, and mould raw bread dough into uniform rolls and buns at high speeds. It replaces the labor-intensive process of scaling and shaping dough by hand, making it a staple machine for small-to-medium commercial bakeries, wholesale bakers, and supermarket in-store bakeries. 1. Primary Functions: Dividing: It automatically cuts a bulk mass of dough into precise, equal weights without tearing the dough structure. Rounding: It rolls the divided dough portions into tight, consistent round dough balls (baps, dinner rolls). Pinning & Moulding: The integrated "pinner" section flattens and rolls the round dough pieces into elongated shapes (finger rolls, hot dog buns). 2. Specific Bakery Products It Creates: By changing the internal moulding drums or adjusting the pinner belts, bakeries use this machine to produce: Round items: Hamburger buns, traditional baps, dinner rolls, and slider buns. Elongated items: Hot dog rolls, finger rolls, bridge rolls, submarine rolls, and miniature baguettes/batards up to 230mm long. 3. Why Bakeries Use It (Key Benefits): Massive Labour Savings: It can produce up to 6,000 rolls per hour (100 rolls every minute), a volume that would require a large team of bakers to do manually. Cost Efficiency (Oil-Free System): Unlike traditional dividers that require expensive food-grade divider oil to keep dough from sticking, the Novatek uses a completely dry, oil-free process. This saves thousands of pounds annually in oil costs and makes cleanup much easier. Product Consistency: Every roll comes out exactly the same weight (from 10g up to 208g in 2-row mode) and the same shape, which ensures uniform baking times and presentation. Physical Dimensions & Spatial Footprint: Standard Operating Footprint: Typically occupies a width of 0.8 m to 1.2 m and a base chassis length of 1.5 m to 2.5 m. Extended Length with Integral Pinner: When configured with the long-bed outfeed pinner/moulder belt assembly, the total inline workspace length requires approximately 3.2 m to 3.8 m to clear the outfeed table. Operating Height: Roughly 1.6 m to 1.8 m to the top rim of the bulk dough feed hopper to facilitate ergonomic manual or conveyor loading. Total Net Weight: Approximately 950 kg to 1,200 kg depending on the configuration of heavy-duty plunger blocks, internal moulding drums, and chassis reinforcement. Operational & Production Capabilities. Throughput Capacity: Processes up to 50 dough pieces per minute per row. For a standard 2-pocket (2-lane) configuration, this delivers a maximum output of 6,000 pieces per hour. Hopper Capacity: Features a standard integrated bulk dough conveyor hopper that accommodates 55 kg of raw dough. Scaling Ranges: 2-Row Operation: Scales between 10 g and 208 g simultaneously across both lanes. 1-Row Operation: Reaches 208 g to 500 g utilising lane blanking and larger interchangeable plunger blocks. Pinner Capabilities: Accurately stretches and shapes rounded dough pieces into finger rolls, hot dog buns, or miniature batards up to a maximum length of 230 mm. Iijdpsz Ad Dcefx Anijh Utility & Facility Requirements: Electrical Supply: Requires a standard industrial 3-phase 400V, 50Hz electrical hookup.

Condition: like new (used), Year of construction: 2022, operating hours: 458 h, functionality: fully functional, machine/vehicle number: 1536582684A, travel distance X-axis: 500 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, nominal power (apparent): 30 kVA, torque: 83 Nm, workpiece height (max.): 550 mm, workpiece diameter (max.): 630 mm, workpiece weight (max.): 200 kg, total height: 3,200 mm, total length: 4,500 mm, total width: 3,500 mm, rotational speed (min.): 20 rpm, rotational speed (max.): 12,000 rpm, overall weight: 4,700 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 13 W, number of spindles: 3, number of slots in tool magazine: 30, tool diameter: 80 mm, tool weight: 8 g, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, We offer this DMG MORI CMX 50 U universal machining center, in like-new condition. Operating hours: Power-on hours: 458 h / Spindle: 330 h, year of manufacture 2022. TECHNICAL DATA Axis travels: • X = 500 mm • Y = 450 mm • Z = 400 mm • B = -5° / +110° • C = n × 360° Work table: • 630 × 500 mm pivoting rotary table • 7 T 14 H7 grooves, 63 mm pitch • Central hole Ø 30 H6 • Permissible table load: 200 kg • Axis – table distance: 150–550 mm Main spindle (inline spindle): • Speed: 20 – 12,000 rpm • Power: 13 kW (40% DC) / 9 kW (100% DC) • Torque: 83 Nm (40% DC) / 57 Nm (100% DC) • Tool shank: SK40 DIN 69871 • Clamping according to DIN 69872, hydraulic control • Clamping force SK40/BT40: 10 kN Tool magazine: • 30 positions, chain with double gripper • Max. tool diameter: 80 mm (130 mm with adjacent pockets free) • Max. tool length: 300 mm (from the spindle face) • Max. tool weight: 8 kg • Max. magazine load: 120 kg • Tool change time: 2.7 s Iiodpfx Aez Epnvonish Feeds and accuracy: • Rapid feed rate X/Y/Z: 30 m/min • Max. feed force (40% DC): 4.5 kN • Linear guide rails with rollers on all axes • Direct measuring system on X, Y, Z (including air purge) • Positioning accuracy X/Y/Z: A = 6 µm (ISO 10791-4) • Repeatability X/Y/Z: R = 5 µm (ISO 10791-4) • Accuracy B/C: A = 16 seconds of arc (ISO 10791-4) • Repeatability B/C: R = 12 seconds of arc (ISO 10791-4) INCLUDED EQUIPMENT Base machine: • CMX 50 U universal machining center (C-A3390F) • DMG MORI SLIMline Multi-Touch 19" / Siemens 840D SL control (C-B3097F) • Coolant or air, switchable via M functions • Chip tray / drawer • Enclosure with sliding door • DMG MORI IoTconnector included as standard 20 bar production package with chip conveyor (C-K3661F): • Internal 20 bar coolant supply • Scraper-type chip conveyor, 250 l tank (left) • Washing of bed and ATC arm via M function • Coolant spray gun • External electronic handwheel • Enclosure roof • 4-color signaling lamp • Double cartridge filter (filter change without stopping the machine) Measurement / monitoring: • Renishaw measuring kit for Siemens (C-K4222F): PP40 probe with optical transmission, TS27R tool probe, measuring cycles with tool breakage monitoring, dummy tool and calibration ring • 3D QuickSET for CMX U (C-K2530F) – control and compensation of 5-axis kinematic accuracy Software and documentation: • DXF Import option on Siemens controller (C-G3067F) • Documentation in Romanian • Screen text in Romanian DMG MORI Digital Products: • Digital production package: IoTconnector, machine data connector MDC (OPC UA / MTConnect / MQTT), NETservice (remote diagnostics) • Messenger V4 – machine status in real time • DMG MORI Service Agent – preventive service warning • Machine 3D model in STEP format (upon signing of NDA, for CAD/CAM) NUMERICAL CONTROL – Siemens SINUMERIK 840D SL • TCU30.3 console, NCU720.3B PN • Safety Integrated • 19" multi-touch screen, 1024 × 1280 • Block processing time: 1.5 ms • User memory 16 MB + 4 GB extension (EES) CONNECTIONS • Standard 12,000 rpm: 30 kVA / 47 A / 50 A fuse at 400 V • With 20/40/80 bar package: 32 kVA / 50 A / 63 A fuse at 400 V • Voltage: 400 V / 230 V, 50/60 Hz, ±10% • Air: 6–8 bar, average consumption approx. 30 m³/h

Condition: excellent (used), functionality: fully functional, Universal milling machine Deckel Maho DMU 50M with line control TNC 124 from Heidenhain TOP condition !!! Technical data: >> Year of construction 1998 >> Heidenhain control TNC 124 >> Traverse paths X500/Y400/Z400 >> C and B axis manual with display >> Speed 20- 4500 1/min >> Feed 5000mm/min >> rapid traverse 5m/min >> Tool holder SK 40 >> Table Ø700x500mm >> swivel range +95° /-10° >> electronic handwheel >> Weight 2800Kg Isdjr Hbf Eopfx Anioih >> Machine dimensions approx. 4.0 m x 2.5 m height 2.6 m >> Coolant device >> Power connection 400V 32A About the machine : We are offering a Deckel Maho DMU 50M universal milling machine with a Heidenhain TNC 124 line control in very good condition. The table is manually (digitally) adjustable by two additional axes B and C. A very easy to operate control, it can enter and approach positions, deep and thread drilling, drilling patterns, hole circles, hole rows and rectangular pocket milling. Programs can be entered and read out via an interface. The Heidenhain line control makes work easier and even more precise. The milling machine was used in a large company for training purposes. Take the opportunity to inspect and try out the machine under power on site.

Condition: excellent (used), functionality: fully functional, Universal milling machine Deckel Maho DMU 50M with line control TNC 124 from Heidenhain TOP condition !!! Iodpor Hbf Tofx Anijih Technical data: >> Year of construction 1998 >> Heidenhain control TNC 124 >> Traverse paths X500/Y400/Z400 >> C and B axis manual with display >> Speed 20- 4500 1/min >> Feed 5000mm/min >> rapid traverse 5m/min >> Tool holder SK 40 >> Table Ø700x500mm >> swivel range +95° /-10° >> electronic handwheel >> Weight 2800Kg >> Machine dimensions approx. 4.0 m x 2.5 m height 2.6 m >> Coolant device >> Power connection 400V 32A About the machine : We are offering a Deckel Maho DMU 50M universal milling machine with a Heidenhain TNC 124 line control in very good condition. The table is manually (digitally) adjustable by two additional axes B and C. A very easy to operate control, it can enter and approach positions, deep and thread drilling, drilling patterns, hole circles, hole rows and rectangular pocket milling. Programs can be entered and read out via an interface. The Heidenhain line control makes work easier and even more precise. The milling machine was used in a large company for training purposes. Take the opportunity to inspect and try out the machine under power on site.

Condition: like new (used), Year of construction: 2015, functionality: fully functional, Tool Milling Machine Kunzmann WF 600M with Heidenhain TNC 128 Control System | Excellent Condition | CE-Compliant! Technical Data: - Year of manufacture: 2015 | Machine No. 610398 - Milling table clamping surface: 800 x 425 mm Iisdpfowz Eu Nex Anish - Clamping slots: 6 - Slot width: 14 H7 - Slot spacing: 63 mm - Maximum load: 300 kg - Spindle speed range: 1 – 4500 rpm - Infinitely variable feed: 0–2000 mm/min - Rapid traverse (X and Y axis): 5000 mm/min - Z axis: 4000 mm/min - Travel (X/Y/Z): 600/400/400 mm - Vertical and horizontal quill: SK40 - Hydraulic clamping system - Weight: approx. 2025 kg - Dimensions (L x W x H): approx. 2 x 2 x 2 m - Main drive motor: AC three-phase motor - Power rating at 100% duty cycle Accessories and Equipment: - Heidenhain TNC 128 control system - Hydraulic clamping, vertical and horizontal - Automatic central lubrication - Spindle brake - Technical documentation, spare parts diagrams, operating manual - Coolant system About the Machine: Offered here is a tool milling machine Kunzmann WF 600M equipped with a Heidenhain TNC 128 control system. The TNC 128 provides numerous dialog-guided cycles with graphical simulation for quick and easy data entry, such as various drilling cycles, tapping, bolt circles, linear hole patterns, rectangular pockets, rectangular tenons, and surface facing. This universal milling machine is in like-new condition. The control system is very easy to operate. Additionally, the machine features hydraulic clamping for both vertical and horizontal operation. Switching from vertical to horizontal is very simple by swiveling the vertical head to the side. The guides are regularly lubricated by the central lubrication system. The Kunzmann has been mechanically and electrically tested at our facility. You are welcome to view and test the Kunzmann under power on-site.

Condition: new, Year of construction: 2022, functionality: fully functional, Kunzmann WF 410M tool milling machine with Heidenhain TNC 128 control. Brand new and CE-compliant! Technical specifications: >> Year of manufacture 2022 Machine no. 411555 >> Milling table clamping area 650 x 375 mm Clamping slots 5 Slot width 14 H 7 Slot spacing 63 mm Maximum load 250 kg >> Speed range 1-4500 rpm >> Feed X, Y, Z axes (infinitely variable) up to max. 5/5/4 m/min >> Travels X/Y/Z: 410/350/450 mm >> Vertical quill and horizontal quill - SK40 >> Hydraulic tightening system >> Weight approx. 2000 kg Iisdpjv Rppkofx Anieh >> Dimensions approx.: 2 x 2 x 2 m >> Connected load 13 kVA Accessories and equipment: >> Heidenhain TNC 128 control >> Heidenhain HR electronic handwheel 510FS >> Vertical and horizontal hydraulic clamping >> Automatic central lubrication >> Spindle brake >> Technical documentation, spare parts plans, operating instructions >> Machine light >> Minimum quantity lubrication >> Counterholder >> Digital display for spindle stroke >> Oriented spindle stop (tapping without compensating chuck) >> Chip protection cabin >> KT 130 edge finder >> Coolant system >> 200 mm rotary table >> Dividing head with 125 mm three- and four-jaw chuck >> 125 mm hydraulic vise About the machine: Offered is a Kunzmann WF 410M tool milling machine, built in 2022, in new condition with a Heidenhain TNC 128 control. The TNC 128 provides numerous dialog-guided cycles with graphic simulation for fast and easy data entry, e.g.: various drilling cycles, thread cutting, bolt circles, hole pattern, rectangular pockets, rectangular tenons, and multi-pass milling of surfaces. A very easy-to-use control system. The machine also has hydraulic clamping for both vertical and horizontal operation. Converting from vertical to horizontal is very easy by folding away the vertical head. The guideways are regularly lubricated by the central lubrication system. The Kunzmann has been mechanically and electrically tested by us. Take advantage of the opportunity to inspect and try out the Kunzmann on site with power on.

Condition: new, functionality: fully functional, Year of construction: 2026, color: grey-black, overall weight: 15,000 kg, maximum load weight: 12,000 kg, empty load weight: 2,300 kg, loading space width: 2,500 mm, loading space length: 6,000 mm, loading space height: 125 mm, Dear Sir or Madam, Iiodezrdc Dopfx Anieh We are offering a new roll-off platform for sale, manufactured in our own production facility. The platform features the following: - Manufactured according to DIN standards - 50mm diameter mounting bracket - Hook height 1570mm - 5mm checkered steel floor / 4mm front wall thickness - Robust hook housing with surrounding steel plates - IPN 180 longitudinal beam / reinforced - External rollers, greaseable and replaceable - Primed, painted in RAL 7016 / anthracite - C-locking mechanism according to DIN - 5 pairs of recessed lashing points with a tensile force of 2.5t each - Lateral perforated rails with 30mm hole spacing - 6x heavy-duty and lockable inserts to compensate for track differences - Tracks recessed by 120mm (125mm ground clearance) - Recessed tracks, each approximately 4780mm long and 708mm wide - 2x lockable steel pockets on the front - 2x lashing rings with 5.3t tensile force each on the inside of the front wall - 2x lashing rings with 5.3t tensile force embedded in the ramp - 2x warning markings according to §32 (1) StVO & DIN - Including type plate & container inspection according to DGUV rule 114-010 (formerly BGR) - Immediately available Also available with a usable platform length of 6.5m and 5.5m. Nationwide delivery is possible for an additional charge! If you are interested in other roll-off container products, we would be happy to receive your inquiry!

Condition: ready for operation (used), An external whirling unit ProCon for external machining of threads and rotationally symmetrical shapes is available. Installation height: 180mm, motor power: 7.5kW, through hole of hollow spindle: 160mm, tilt angle right/left: 28°/45°, speed: 1800rpm, angular resolution: 0.1°, cutting circles: SK70/SK90, cutting circle pockets SK70/SK90: 4(6)/8, cutting circle bore SK70/SK90: 100mm/120mm, weight: approx. 120kg. Documentation available. An on-site inspection is possible. Iisdpfxexnbrue Anieh

Condition: used, Year of construction: 2007, functionality: fully functional, travel distance X-axis: 400 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 380 mm, total height: 2,680 mm, total length: 2,700 mm, total width: 1,900 mm, overall weight: 2,100 kg, type of input current: three-phase, feed length W-axis: 300 mm, power: 6 kW (8.16 HP), drill diameter: 6 mm, Equipment: documentation/manual, Topedm TSH-400T CNC CNC electro-discharge drilling machine with electrode changer and guide changer Year of manufacture: 2007 Includes guides, collets, and various spare parts Operates with brass electrodes Automatic electrode changer Automatic, patented guide changer Predefined machining parameters Repeatability: 0.01 mm Burr-free drilling Automatic electrode wear compensation enables precise blind hole drilling Full water bath machine Water treatment unit Deionized water as dielectric, no additives required Deionization, large filters Water chiller Additional flushing at the guide Technical data Max. travel (X x Y x Z): 400 x 400 x 380 mm Table size: 480 x 458 mm Electrode diameter: 0.15 to 6.0 mm Maximum distance head / table: 315 mm Machine head movement (W-axis): 300 mm Repeatability: ± 0.01 mm Number of positions in automatic electrode changer: 21 Maximum working current: 50 A Automatic guide changer: 5 guides Fillable working tank Working tank size (L x W x H): 670 x 930 x 330 mm Power consumption: 6 kW Footprint (L x W x H): 2700 x 1900 x 2680 mm Weight: 2100 kg Iiodpfx Aoztyxdenijh Optionally, more than 1000 multi-channel brass electrodes, 0.3 to 6 mm, are in stock and can be sold at a favorable price. The machine is in good condition and can be tested under power. Inspection is possible during our business hours or by appointment. The sale is due to upcoming retirement.

Condition: used, maximum load weight: 78,380 kg, overall weight: 97,000 kg, axle configuration: > 3 axles, first registration: 06/2023, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt of the equipment, complete equipment list available upon request. Equipment: * 2-inch kingpin * 12 t Broshuis SL axles Iiodpoz Ifk Eofx Anieh * Extendable width extensions * 4 pairs of lashing points on the central beam, 10,000 daN * 1 pair in the fixed section in front of the telescoping section * 3 pairs behind the telescoping section * 9 pairs of lashing points in the outer frame, 10,000 daN * Holes in the outer frame for attaching lashing straps * Jost 2-speed geared support winch * 4 extendable, illuminated width extension panels * 3 plug-in side panels on the gooseneck (length approx. 2,400 mm) * Rear corner posts, plug-in/removable * 4 sets of shims with holders under the loading platform at the support legs * 1 pair of lashing points in the outer frame of the gooseneck, 10,000 daN * 3 pairs of lashing points in the outer frame of the gooseneck, 5,000 daN * NATO socket - NATO spiral cable - 2 x 7-pole electrical system * 1 x 7-pole EBS - 1 socket at the front and rear for auxiliary steering * 1 storage box on the gooseneck, spanning the entire width, with angled corners (45°) * Opening from above - doors in the corners can be locked (not continuous to the storage box in the middle) * 6 sets of plug-in uprights, approx. 1,200 mm high, incl. holder on the gooseneck * WADER container pockets for 1 x 20 ft and 1 x 40 ft - Brake connections, red/yellow - EBS WABCO * Rear support, telescoping * 2 LED reversing lights at the rear * LED lighting (DK round) * 1 LED rotating beacon * 8 pairs of upright pockets in the outer frame of the loading platform * 3 pairs of upright pockets in the outer frame of the gooseneck * Contour marking, yellow on the sides / red at the rear * Adjustable attachment rails for loading ramps * 3 LED flashing beacons at the rear of the vehicle * RAL 3002 carmine red * 2 ECE plates at the rear

Condition: excellent (used), For sale is a complete, German measurement set for diagnostics and machine adjustments, ideal for service, production, and inspection applications. The set includes: • ROTUX Pocket Strobe™ stroboscopic lamp Isdpfoz Sb S Nex Anijih • Operating range: 30 – 12,500 FPM (flashes per minute) • Built-in display and adjustment knob • Battery-powered (ANSMANN charger included) • Original case with foam padding Additionally: • HOLEX 0–10 mm dial indicator, accuracy 0.01 mm • NOGA magnetic stand with adjustment • Set of attachments and holders • Mounting elements and cables • All in good working condition, equipment from an operational workshop Made in: Germany Condition: very good, complete set, not heavily used ⸻ Ideal for a service technician, precision mechanic, or for inspecting rotational movement, alignment, vibrations, or synchronization in drive systems. The ROTUX lamp is a professional tool, not a cheap Chinese substitute.

Condition: new, maximum load weight: 36,190 kg, overall weight: 42,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list: Complete equipment available upon request. Chassis * Regular ladder frame in lightweight steel construction with continuous crossmembers * Frame extended forward * Coupling plate approx. 8 mm thick, with a 2-inch fifth-wheel kingpin according to DIN 74080 / ISO 337 Axle * Axle lift mechanism on axle 1, with fully automatic, load-dependent axle lift control * Starting assist: Activated via 3x brake application, 30% overload up to a speed of 25 km/h * Operation on the chassis via switches * Also possible from the cab (switch in the cab required - PIN 12) * Manufacturer to be chosen: Kögel * Three-axle unit, with disc brakes Ø approx. 430 mm, offset approx. 120 mm * Air suspension with approx. 180 mm travel Vehicle tires * Wheels with internal sensors according to UN ECE R141 * Tires 6x 385/65 R 22.5, ATHOS HG 2144 (164J) Chassis components * Fifth-wheel mounting (manufacturer to be chosen by Kögel) mechanically with leveling foot, 24 t lifting capacity. * One-sided operation on the driving side (right side). * Splash protection system (spray mist suppression) according to Regulation (EU) No. 109/2011 for three-axle unit with tires 385/65 R22.5 * Consisting of 1 pair of quarter-circle fenders in front of the axles * 1 pair of straight fenders with mud flaps between the 1st and 2nd axles and 1 pair of quarter-circle fenders with mud flaps behind the axles. * Lateral protection device according to ECE-R73. * 2 plastic toolboxes, waterproof, dimensions (internal) approx. 525 x 390 x 410 mm. Installation at the rear, 1x on the left and 1x on the right. * High, rigid rear underrun protection made of steel according to ECE-R58 * 1 pair of retractable warning signs (approx. 280x280mm) for over-width loads, retroreflectively red / white, with LED lighting, spiral cable and plug connection. Brake / Air Suspension System * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS plug connection ISO 7638, (without connection lines) * Parking brake as spring-loaded brake, external pneumatic connections and external EBS diagnostic connection via ISO 7638 plug connection. * WABCO EBS system * Air suspension system incl. 1 lifting and lowering valve, mounted on the driving side behind the axle unit * Driving position is automatically adjusted. * 2 non-interchangeable coupling heads at the front * Air tank for braking system and air reservoir made of steel (EN 286-2) Ijdpfjz N Nxdsx Anijih Floor * Plate floor approx. 30 mm thick * Floor sealed around the perimeter, pocket rails for square tube inserts approx. 80 x 80, arrangement according to drawing * 8 pieces of pocket rail strips (18 pocket rails per strip: 4 pieces each on the outside + 10 pieces in the middle) Front Wall * Storage for max. 20 square tube inserts 80 x 80 (length 1,990 mm) on the inside of the front wall * Front wall approx. 2,000 mm high with steel corner posts, with profiled steel sheet, screwed/riveted to the frame. * 2 pairs of lashing points (permissible lashing force approx. 1,000 kg per ring) on the front end according to EN 12640. * Side wall VarioFix steel hole outer frame without rail storage * 21 pairs of lashing eyes in the outer frame (according to EN 12640), permissible pulling force approx. 5,000 kg per ring. Impact Protection * 1 pair of steel impact buffers approx. 160x85x85mm mounted on the frame end plate

Condition: used, Year of construction: 2001, functionality: fully functional, machine/vehicle number: 919, power of the servo motor: 750 W, input voltage: 400 V, type of input current: three-phase, feed length X-axis: 150 mm, feed length Y-axis: 100 mm, 8 C – JAM TC 138-EP-FC Automatic Pocket Setter with Brother Sewing Head (2001) CNC Controlled Automatic Pocket Setting Workstation for Jeans & Workwear Production Professional-grade JAM TC 138-EP-FC Automatic Pocket Setter equipped with a high-performance Brother automated sewing system. Manufactured by JAM s.r.l. (Italy), this fully integrated workstation is designed for automated folding and stitching of patch pockets used in jeans, workwear, jackets, and other garment applications requiring high productivity and repeatable quality. The machine combines programmable CNC-controlled sewing, automated pneumatic material handling, precision folding templates, and automatic positioning technology. The system is capable of folding and sewing pocket components with minimal operator intervention while maintaining consistent quality throughout long production runs. The unit was previously used in professional garment manufacturing and remained operational until factory shutdown. Technical Specifications • Manufacturer: JAM s.r.l. • Model: TC 138-EP-FC • Year of Manufacture: 2001 • Machine Number (Matricola): 919 • Reference Number: 8 C • Sewing Head: Brother Automated Sewing Unit • Control System: Brother BAS CNC Controller • Automation Platform: JAM System • Servo Motor Power: 750 W • Power Supply: 400 V, 3-Phase • Frequency: 50/60 Hz • Motor Speed: o 1390 rpm (50 Hz) o 1680 rpm (60 Hz) • X-Axis Feed Length: 150 mm • Y-Axis Feed Length: 100 mm • Pneumatic Supply Required Key Features • Fully automated pocket setting workstation • CNC-controlled programmable sewing system • Automated pocket folding and positioning • Pneumatic clamping and material handling • Fast pattern change capability • High repeatability and consistent stitch quality • Designed for continuous industrial production • Heavy-duty Italian automation platform • Integrated Brother sewing technology • Suitable for denim, workwear, and garment manufacturing Includes • JAM TC 138-EP-FC automated pocket setter • Brother automated sewing head • Brother BAS CNC control system • Dual control panel interface • Integrated pneumatic clamping system • Automated fabric handling system • Pocket folding templates and guides • Stainless steel workstation table • Industrial steel frame • Safety guards • Integrated workstation lighting • Pneumatic components and connections Applications • Automatic patch pocket attachment • Jeans pocket setting • Workwear pocket production • Chino and trouser pocket attachment • Garment component sewing • Reinforcement stitching Ijdpfxszgw Ebj Anisih • Label attachment operations • High-volume apparel manufacturing Condition • Fully functional • Operational prior to factory shutdown • Serviced on 27.02.2026 • Good industrial condition • Normal cosmetic wear consistent with production use • Available for inspection before dismantling Location Valga, Estonia Dismantling & Transport Buyer responsible for dismantling, loading, transportation, and all related costs. Professional dismantling is recommended due to the machine's CNC control system, pneumatic components, and calibration requirements. Sales Terms Sold as-is, where-is, without warranty. Part of the MASI Jeans factory liquidation.

Condition: new, maximum load weight: 51,780 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Here is an excerpt of the equipment. Complete equipment details are available upon request. Ijdpfx Ajz N Nxwjnijih GOOSENECK: Gooseneck with SNT design to optimize the loading area length, approximately 3,700 mm long, with a taper at the rear of approximately 1,000 mm x 10°. For SZM: 4 x 2, 6 x 2, and 6 x 4. Steel front wall, plug-in, approximately 400 mm high. ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets. 3 kW electric-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches. Outrigger of the gooseneck with mounting holes for screwable lashing rings. One mounting hole in the rear upper area of the gooseneck outrigger for a screwable lashing ring. 1 pair of screwable lashing rings included (LC 10,000 daN). On the gooseneck, 1 pair of plug-in aluminum side panels, approximately 400 mm high, in an anodized finish. On the gooseneck, one plug-in aluminum rear panel, approximately 400 mm high, in an anodized finish. Approximately 40 mm thick hardwood flooring above the gooseneck. 2-inch kingpin. 1 crossmember pocket rail mounted in the loading bed of the gooseneck in front of the taper, for plug-in crossmembers, approximately 100 x 50 mm. LOADING AREA: Loading area in an extendable design, approximately 8,800 mm long, with a taper at the rear of approximately 500 mm x 10°. A recess in the loading area that extends into the taper to accommodate the excavator arm, approximately 2,490 x 750 x 210/290 mm (L x W x H). TPMS tire pressure monitoring system according to ECE R 141. BPW axles and suspension, 1st and 2nd axles rigid, 3rd and 4th axles steered. 3rd and 4th axles with electro-magnetic reverse locking via reverse gear and can be activated manually. Technical axle load: 12,000 kg each. Air suspension with lifting and lowering valve. Mechanical fifth-wheel supports with 2-speed gearbox and crank. Continuous hardwood flooring approximately 50 mm thick in the loading area, interrupted between the axles (thus increasing the coefficient of friction). 1 intermediate table with a recessed loading area, approximately 300 mm wide, for the extension tube with a large cross-section and sheet metal flooring. 1 pair of lashing rings on the front crossmember (LC 10,000 daN). 6 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN). Additionally, 1 pair of lashing rings on the outside of the front crossmember of the loading area, rotated approximately 90° inwards towards the loading area (LC 10,000 daN). Extensions (galvanized), extendable approximately 230 mm on each side (without wooden planks). 1 pair of fixed wheel arches, open to the extension, approximately 700 x 410 mm (W x D), in the loading area in front of the 1st axle. Between the 2nd and 3rd axles in the loading area, 1 pair of fixed wheel arches, approximately 1,695 x 700 x 410 mm (L x W x D). 1 pair of mechanical rear supports. 245/70 R 17.5 3PMSF twin tires - brand of our choice. HYDRAULIC LOADING RAMPS: DR-15/60-900-4350-HB-HV-M. A pair of two-piece steel ramps with a length of approximately 4,350 mm and a width of approximately 900 mm. Hardwood flooring. Hydraulically foldable ramp tips. Ramps can be individually hydraulically moved outwards approximately 235 mm and inwards approximately 215 mm. Hardwood flooring on the taper of the loading area. Ramp with hardwood fl

Condition: used, maximum load weight: 35,560 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 01/2026, next inspection (TÜV): 01/2027, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list: Complete equipment available upon request. Chassis * Regular ladder frame in lightweight steel construction * with continuous cross members, coupling plate 8 mm thick * with a 2-point kingpin according to DIN 74080 / ISO 337 Suspension * Axle lift mechanism on axle 1, brand according to choice, Kögel * Three-axle unit * with disc brakes Ø 430 mm * Offset approx. 120 mm, air suspension with approx. 180 mm travel Vehicle tires * 6x 385/65 R 22.5 UNIROYAL TH 50 Chassis components * Landing gear (brand according to choice from Kögel), mechanically operated with leveling foot, lifting capacity approx. 24 t * One-sided operation on the right side when driving, splash protection system (spray mist suppression) according to Regulation (EU) No. 109/2011 * for three-axle unit with 385/65 R22.5 tires * consisting of 1 pair of quarter-circle fenders in front of the axles * 1 pair of straight fenders with mud flaps between the 1st and 2nd axles * 1 pair of quarter-circle fenders with mud flaps behind the axles * Storage box for: 10 side panels, folding stanchions, and rear door or rear flap. * Fully enclosed, protected against spray, also serves as a side protection, ground clearance (front) 220 mm * 2 plastic toolboxes, watertight, dimensions (internal) approx. 545 x 400 x 400 mm. * Installation at the rear, 1x on the left and 1x on the right, high, rigid underrun protection at the rear made of steel according to ECE-R58 * 1 pair of retractable warning signs for overwidth loads, retroreflective red/white, with LED lighting, spiral cable, and plug connection * Arrangement in the front and rear Vehicle area, brake / air suspension system * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS plug connection ISO 7638 (without connection cables) * Parking brake as spring-loaded brake * external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 plug connection * WABCO EBS system * Air suspension system including 1 raising and lowering valve, mounted on the left side behind the axle unit when driving * Driving position adjusts automatically, 2 tamper-proof coupling heads in front ISO 1728 * Air tanks for brake system and air reservoir made of steel (EN 286-2) * Floor, flat floor approx. 30 mm thick, floor sealed around the perimeter, pocket for square tube inserts approx. 80 x 80 mm, arrangement according to drawing * 8 pieces of pocket strips (18 pockets per strip, 4 each on the outside + 10 in the middle) * Body, meets body strength according to EN 12642 XL (VDI 2700) * Tested for a payload of approx. 27,000 kg, front wall, storage for max. 14 square tube inserts approx. 80 x 80 mm (length approx. 1,990 mm) on the inside of the front wall, front wall approx. 2,000 mm high with steel corner brackets, with profiled steel sheet, screwed/riveted to the frame. * 2 pairs of lashing points (allowable lashing force approx. 1,000 kg per ring) on the front wall according to EN 12640 * Rear wall, foldable rear wall approx. 600 mm made of aluminum hollow profiles with 3 tension bars and T-handle locking mechanisms * 2 folding steps on the inside, folding steel corner brackets at the rear at the height of the side panels * Side wall, 4 pairs of folding stanchions at the height of the side panels * VarioFix steel hole outer frame Isdpfx Anszz Umxeioih * 4 pairs of stanchio

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: 254002, type of input current: three-phase, overall weight: 130 kg, input voltage: 380 V, number of spindles: 8, input frequency: 50 Hz, Schleicher frame dowel hole drilling machine DBH 600, Drilling motor 1.5 kW, 380 Volt, 50 Hz, Drilling stroke 0 - 130 mm, Special drilling gear with 3 rows and 8 spindles, 1 clamping cylinder, Iijdez Nkutopfx Anieh Special stop system for window frames and window mullions Weight approximately 130 kg as is, at the Seevetal location, excluding transport, EXW (Ex Works), subject to prior sale.

Condition: new, Year of construction: 2024, travel distance X-axis: 800 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 800 mm, Highlights: - Powerfull motorizied spindle 16.000 U/min | 206 Nm - Hydraulic clamping for fixtures - High pressure cutting fluid system (80 bar) _____ Basic machine G440 Travels: X=800, Y=800, Z=800 mm Power supply 400 V, 50 Hz, TN-S Machine cooling system with a air-cooled cooling unit (20 kW) SIEMENS SINUMERIK 840D sl with machine control panel GROB4Pilot access Motorized spindle HSK-A 63, 16,000 rpm, 159/206 Nm, 25/32 kW, oil-air lubrication (GROB) GROB spindle diagnostics GSD Rotary table with GROB pallet clamping system (B-axis) Double disk-type tool magazine HSK-A 63 with 117 (57|60) tool pockets Tool cleaning device Electromechanical tool breakage detection device Pallet change system for two pallets Setup station rotated manually Setup station door, manually-operated, for manual loading/unloading Pallet, 500x500 mm, grid with tapped holes Equipping the pallet with 4 fluid connections Scraper-type conveyor, for larger quantities, discharge height 1,100 mm High-pressure cutting fluid system (10-80 bar, ICS) Compressed air feed through spindle center External compressed air supply via a flexibly adjustable hose Oil skimmer for cutting fluid care Flush gun at the work area Part clamping system in work area - KP1: Pressure oil, manual pressure reduction, 30-200 bar (H1.1) - KP2: Pressure oil, manual pressure reduction, 30-200 bar (H1.1) Part clamping system in setup station of pallet changer - KP1: Pressure oil, manual pressure reduction, 30-200 bar (H1.1) - KP2: Pressure oil, manual pressure reduction, 30-200 bar (H1.1) - KP3: Pressure oil, manual pressure reduction, 30-200 bar (H1.1) - KP4: Pressure oil, manual pressure reduction, 30-200 bar (H1.1) Preparations for using infrared touch probe OMP60 (RENISHAW) Iisdjr Nbzxspfx Anieh Rotating inspection glass for work area door Remote machine diagnostics with access control switch 12-month warranty

Condition: new, maximum load weight: 29,731 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 13,580 mm, loading space width: 2,480 mm, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Brand new Kässbohrer K.SPS platform semi-trailer Immediately available Technical data: * Outer length 13,640 mm * Internal length 13,580 mm * Axle distance 1,310 mm * Wheelbase 7,700 mm * Overall width 2,550 mm * Inner width 2,480 mm * Gooseneck 200 mm * Semi-mounted height 1,180 mm * Axle load 27,000 kg * Kingpin capacity 12,000 kg * Total weight 39,000 kg * Unladen weight 6,269 kg * Pallet capacity 33 Euro pallet load capacity Chassis: * BPW axles with air suspension and disc brakes * 1st axle can be lifted automatically * Wabco brake system * 6 tires 385765 R22.5 * Axle pressure gauge Chassis: Iodpfx Aeqbn R Nonijih * Made of high-quality and durable steel * KTL-coated steel front panel with plywood protection inside with a height of 2,000 mm * Hardwood-coated, 30 mm thick and waterproof hardwood floor, which can take an axle load of 7,200 kg in accordance with DIN EN 283. * Jost supports * LED lighting * Load securing. * K-fix has 96 holes per side, each lashing point has a load capacity of 2,500 kg * Additional 7x2 lashing rings placed on the floor with a load capacity of 5,000 kg * 6x2 container locks suitable for 1x20 ft in the middle, 2x20 ft, 1x40 ft containers * Stake pockets outside + on the floor * Stake box under chassis * Load securing certificate according to standard EN 12642 CodeXL Miscellaneous: * 1x stainless steel toolbox * 4x extra wide boards with LED lighting Chassis color: MB 7350 nova grey For further information please do not hesitate to contact us

Condition: ready for operation (used), pressure 30.0 t punching cross-cut in cmm 30.0 in 9.0 mm stroke ca. 35 Hub/min throat 610 mm Ijdexaaipepfx Anisih stroke - stepless adjustable 0 - 28.0 mm oil volume 35.0 l work height max. 1010 mm total power requirement 4.0 kW weight of the machine ca. 1200 kg. range L-W-H 1400 x 700 x 1600 mm good condition (!!) with a lot of application tools (stamps/dies) Furnishing: - electro-hydraulic hole punch, with large throat - Material/sheet metal scrapers including scraper plates - Large material support table, with adjustable depth stops - continuous stroke adjustment - freely movable foot switch including protective cover - Forklift pockets for easy transport - side storage area - lots of accessories + tools - including tool cabinet - Matrix base (for special size matrices) - Stamp holders (for special size stamps) - original user manuel

Condition: used, Year of construction: 1974, operating hours: 10,000 h, functionality: fully functional, machine/vehicle number: 8002/6410, drilling depth: 1,000 mm, drill diameter: 30 mm, type of input current: three-phase, spindle motor power: 21 W, table length: 1,000 mm, input voltage: 550 V, mount diameter: 160 mm, number of spindles: 1, drilling capacity: 1,000 mm, quill diameter: 30 mm, Equipment: rotational speed infinitely variable, Deep hole drilling machine for up to 1000 mm and 30 mm diameter, used for drilling aluminium, regularly serviced, includes a significant quantity of drills. Machine is fully operational and in continuous use. Siemens control, Simatic PANEL, documentation available. Iijdpex Ehg Tofx Anijh

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, travel distance X-axis: 350 mm, type of input current: three-phase, Sarix SX200HPM with integrated divider. Iiodpoz I R Tfofx Anieh

Condition: ready for operation (used), Year of construction: 2018, operating hours: 7,800 h, travel distance X-axis: 1,067 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 610 mm, controller manufacturer: HURCO, controller model: MAX5, overall weight: 6,850 kg, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 30, number of axes: 3, This 3-axis Hurco VMX 42i was manufactured in 2018 and features X, Y, and Z travels of 1067 mm, 610 mm, and 610 mm respectively. It boasts a maximum spindle speed of 12000 rpm. If you are looking to get high-quality milling capabilities consider the Hurco VMX 42i machine we have for sale. Contact us for more information about this machine. • Tool magazine capacity: 30 tools • Spindle hours: approx. 7,800 h (estimated) • Due to the installation of a new hard drive, the spindle hours can no longer be accurately verified. • Machine weight: approx. 6,850 kg • Total power requirement: approx. 28 kVA • Only steel and aluminium have been machined. • Internal coolant system • The machine has a double-wound AC spindle motor. • The axes are also directly driven. • The machine does not have a direct measurement system. Additional equipment • Chip conveyor • WinMax Mill Version V09.01.39314 • Removable handwheel • No Accessories included, but can be purchased at a reasonable price for an additional charge. Software Features Adaptipath: Trochoidal milling for higher removal rates, controlled engagement, and residual material detectionDialog / NC Mix: Allows mixing of Dialog and NC programsNCPP (Industry Standard Software): • ISNC extended NC mode for FANUC compatibility (FANUC 0) • Parameter and MACRO programming • Subprogram technology for NC modeUlti-Motion: • Dynamic Lookahead (up to 10,000 blocks) • Improved surface quality via "Motion Control Technology" • Reduced cycle times and machine wearStandard Features: • Simulation graphics • Pocket milling with islands • Synchronous tapping (without compensation chuck) Hardware Components & Accessories • Cooling & Chips: • High-pressure coolant system (Through-Spindle Coolant) at 20 bar (Emulsion type) • Spindle cooler • Standard coolant system with spray gun • Chip conveyor and flushing system for chip removal • Chip splash guard cabin • Tooling: Integrated hydraulic tool clamping system • Workspace: • LED machine light • Signal light for operating statuswith deep-hole drilling cycle function Isdpfxjy Tw R Hs Anisih Technical Specification Taper Size SK 40 Through-spindle Coolant Yes

Condition: used, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 03/2025, next inspection (TÜV): 08/2027, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Iiedpfx Anozz Ei Reijh GOOSENECK * Designed in SNT for optimized loading area length * Length approx. 3,700 mm, with a rear slope of approx. 1,000 mm x 10°. For SZM: 4 x 2, 6 x 2, and 6 x 4. * Front panel made of steel, plug-in type, approx. 400 mm high * ASPÖCK-UNIBOX on the connection strip at the front with sockets * 3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches * Without installation of the supply connections on the SZM * Outriggers on the gooseneck with mounting holes for screw-on lashing rings * The first hole is approx. 200 mm from the front, followed by one every approx. 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings in the rear area of the gooseneck (LC 10,000 daN) * Approx. 40 mm thick hardwood deck above the gooseneck * 2-inch kingpin * Guide plate on the gooseneck for the turntable, approx. 500 mm wide * 1 pair of recessed bolster pockets on the gooseneck for plug-in bolsters, approx. 100 x 50 mm LOADING AREA * In an extendable design, length approx. 8,800 mm with a slope at the rear of approx. 500 mm x 10°. * A recess in the loading area and extending into the slope for accommodating the excavator arm, approx. 2,490 x 750 x 210/290 mm (L x W x H). * TPMS tire pressure monitoring system according to ECE R 141. * Mechanical landing gear with 2-speed gearbox and crank. JOST Module B * Static test load = approx. 50,000 kg * Continuous hardwood deck, approx. 50 mm thick, on the loading area and interrupted between the axles (this increases the coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with a large cross-section. * 1 pair of fixed wheel recesses in front of the axles, open to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * Wheel recesses with square ladder strips approx. 15 x 15 mm and widening in the lower area - 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the loading area between the 1st and 2nd axles. Wheel recesses with square ladder strips approx. 15 x 15 mm and widening in the lower area * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axles, which can also be used as widening boards (if the vehicle is equipped with extendable wideners) * 1st axle with starting aid BPW axles and suspension * 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock via reverse gear and can be activated manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve. * 235/75 R 17.5 3PMSF twin tires. Manufacturer of our choice HYDRAULIC LOADING RAMPS * DR-15/60-900-4350-HB-HV-M * A pair of two-piece steel ramps * with a length of approx. 4,350 mm and a width of approx. 900 mm. Hardwood deck * Hydraulically folding ramp tips. Ramps can be individually shifted hydraulically outwards by approx. 235 mm and inwards by approx. 215 mm * Maximum load and angle of inclination according to the technical data sheet: C465497 * In accordance with Regulation 2021/535/EU, ramps with a length of less than 300 mm do not need to be taken into account in the vehicle length of 16,500 mm in the driving position. * Hardwood deck on the slope of the loadin

Year of construction: 1986, condition: ready for operation (used), We offer this ready for use K. Widmann 0271E.20 Punched pockets machine, year of construction 1986. Control voltage: 220 V Iijdpfsz Akq Nox Anijh Frequency: 50 Hz Operating voltage: 380 V Serial number: 89024E011 Circuit diagram number: A If you have any questions or need more information, feel free to send us a message or give us a call.