Used Section Bending Machine for sale (65,503)

Condition: used, Semi-automatic tube bending machine, mandrel tube bender MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Cpjdpfx Ajpu R Nvjgkew Serial No. Year of construction for simultaneous bending of two steel tube sections up to Ø 12 mm Bending angle max. 90° Tube diameter max. 12 mm Mandrel length approx. 65 mm Rated power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Power supply 400 Volt, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Angle input control via STÖBER Controlbox Series 4000/5000 - SIEMENS S7-200 control with TD200 display - Machine without bending tools and without tool storage pins 25 x 183 mm - Only 1 bending mandrel available (see pictures). Required space (L x W x H) 1000 x 1000 x 1500 mm Weight 390 kg Good condition

Condition: used, Manual pipe bender, pipe bending device, mandrel bending machine Hand-held pipe bender, hand-held wire bending machine, bending machine Cjdpfx Ajwhf Hfegkjpw Manufacturer: MEWAG Bending capacity: max. Ø 16 mm 1 bending tool Ø 15 mm with 25 mm bending radius 1 bending tool Ø 10 mm with 16 mm bending radius 1 bending tool Ø 8 mm with 9 mm bending radius 1 bending tool Ø 6 mm with 8 mm bending radius 1 bending tool Ø 5 mm with 8 mm bending radius - Rotating plate with degree markings - Scope of delivery as shown - Wooden box for storage Dimensions L x W x H: 570 x 480 x 145 mm Weight: 43 kg Good condition

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Cpedpfx Ajwbvmiogkow Weight: 110 kg Very good condition

Condition: used, Pneumatic folding and edging machine FASTI Type 606 - 11 - 1.0 Folding machine for pre-forming sheet metal seams For producing a seam bend Seam bending machine for thin sheet metal as an alternative to a press brake Serial no.: 9166002 Year of manufacture: 1991 Working length: 1100 mm Material thickness at 45 kg/mm²: 1 mm Csdpfx Agedzqblekspw Compressed air requirement: 6 bar - pneumatic foot switch - roller adjustment via threaded clamping screws Required space (L x W x H): 1600 x 300 x 1050 mm Weight: approx. 250 kg Good condition The seam is the doubling over of the sheet metal edge (1x folded over) to increase the stiffness of the sheet. By folding over, a rounded edge is created, reducing the risk of injury from sharp sheet edges. Ideal for metalworking applications such as sheet metal furniture, cladding panels, or for the production of ventilation and silencer components.

Condition: used, Hand - swing bending machine KRAMER type AMS 650 x 1,5 Hand swivel bending machine, press brake year of construction approx. 1985 working length 650 mm sheet thickness at 40 kg/mm2 1,5 mm Csdpfx Aedzqaaogkepw upper beam opening approx. 60 mm bending beam adjustment ca- 0-25 mm bending angle 0-180 - Upper beam adjustment via hand crank - pre-screw rail for the bending beam - one-piece sharpening rail 135° space requirement L x W x H 1200 x 600 x 1100 mm weight 160 kg good condition

Condition: used, functionality: fully functional, Year of construction: 2011, operating hours: 500 h, control type: PLC-controlled, degree of automation: automatic, actuation type: hydraulic, pipe length (max.): 3,000 mm, tube wall thickness (max.): 2 mm, bending angle (max.): 180 °, overall weight: 300 kg, power: 1.5 kW (2.04 HP), input voltage: 220 V, input current: 12 A, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, Metalworking company sell megabender 030 In the equipment have mandrels for tube: 60,3mm x 2mm R120 50mm x 2mm R75 40mm x 2mm R60 32mm x 2mm R100 700 kg Cpodpev Di Dnofx Agksw - Powerful mandrel bending machine up to 2 "gas pipe (60.3mm) in semi-automatic design (3000 mm pipe slide length) - Electromechanical drive of the bending axis - hydraulic clamping - mandrel feed / extract - 30 programs x 9 bending angle + correction angle Stainless steel 2mm steel 3mm cooper and aluminium up to 4mm

Condition: good (used), Year of construction: 1962, Manufacturer: VEB Type: RV16 Machinable cross-section: 120 x 140 mm Cjdpfxoltiy Ts Agkepw Weight: 2,7 t

Condition: good (used), Year of construction: 1996, control type: CNC control, Tube diameter: 4-28 mm Cedjyqxnajpfx Agkspw Wall thickness: / mm Minimum bending radius: 1.5 x D - 2.0 x D mm Control: Siemens LOGO Delivery rate: 4.5 l/min Max. bending angle +/-: 190° Nominal pressure: 250 bar Operating pressure: 3095 bar Delivery rate: 4.5 l/min Total power requirement: 1.5 kW Drive: Hydraulic cylinder and roller chain

Condition: good (used), Year of construction: 2005, control type: CNC control, - Max. bending angle: +/- 180 + 10° - Tube feed length: 4100 mm Cpsdpfx Ajyqxmpjgkjw - Round steel tube up to 30 x 2.2 mm² - Round stainless steel tube up to 30 x 1.5 mm - Square tubes: 20 x 2.5 mm - Bending time for 90 degrees: 1.5 sec (advance) - Longitudinal feed speed: 450 mm/sec - Maximum bending radius: 125 mm - Freestanding bending head, 850 mm long - Bending axis drive: electrohydraulic

Condition: good (used), Year of construction: 2008, control type: CNC control, Stainless steel tube diameter: up to 42 x 2.0 mm Steel tube diameter: up to 42 x 3.0 mm Cpjdpfeyqxknex Agkew Max. bending angle: +/- 180 + 10° Section modulus: 4.1 ccm Operating pressure: 6 bar Total power requirement: 5.5 kW Machine weight approx.: 3 t Space requirement approx.: 6100 x 2300 x 1300 mm

Condition: good (used), Year of construction: 1991, 3-roll plate bending machine Plate width: 3000 mm Plate thickness: 20 mm Pre-bending: 16 mm Top roll diameter: 380 mm Side roll diameter: 340 mm Cpsdpfxjyqw Tze Agkew

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, overall weight: 1,500 kg, total length: 3,100 mm, total height: 1,250 mm, total width: 1,100 mm, For sale is a very well-maintained PROD-MASZ ZGH 3140 / 1.2 hydraulic folding machine in professional industrial configuration. This machine stands out due to its robust, torsion-resistant construction, precise bending results, and a generous working length of 3,140 mm. It is ideally suited for roofers, plumbers, metal fabricators, façade constructors, as well as for industrial profile production. The machine was purchased new on 20.08.2020 for €19,000 net (including rotary shear and delivery). Both technically and visually, the folding machine is in excellent condition and is fully operational. General Information Model: ZGH 3140 / 1.2 Year of manufacture: 2020 Manufacturer: PROD-MASZ Machine type: Hydraulic folding machine Working length: 3,140 mm Max. sheet thickness (steel): 1.2 mm Max. sheet thickness (aluminum): approx. 1.5 mm Power supply: 400V / 50 Hz Technical Features Drive / Hydraulics Hydraulic drive Motor power: approx. 2.2 – 3.0 kW Industrial hydraulic unit Foot pedal control Machine dimensions Total length: approx. 3,900 mm Total width: approx. 900 mm Total height: approx. 1,250 mm Weight Machine weight: approx. 1,350 – 1,500 kg Bending system Segmented upper beam Motorized bending motion Precise angle adjustment Suitable for long folding profiles Back gauge system Back gauge included Manually adjustable Scale for reproducible series production Design Heavy-duty, torsion-resistant steel frame Powder-coated industrial finish Stable base frame with integrated hydraulic unit Cpedpfx Asyrd Izsgkow Accessories Rotary shear Inspection possible by appointment. If you have any further questions, please feel free to contact me.

Condition: excellent (used), Year of construction: 2014, sheet width 2600 mm plate thickness 10.0 mm ST pre-bending 8.0 mm ST diameter of upper rolls ~ 220 mm side roll diameter ~ 170 mm diameter of lower rolls ~ 190 mm Control konv. oil volume 80.0 Liter voltage 380 V total power requirement 5.5 kW weight ca. 5000 kg Dimensions (only the machine) ca. 3500 x 1550 x 1400 mm very good condition (!!) current new price incl. accessories approx. 120.000 Euro special price on request Equipment: - robust electro-hydraulic 4-roll round bending machine - 4-roll concept offers a wide range of bending and rounding options - Swivel-mounted control unit * Operation - control of all rollers or machine axes * Digital position display of the side rollers * Manual operation via JOY sticks - Two central rollers are driven directly via hydraulic motors - Conical rolling possible by tilting the rollers - Parallelism of the side rollers via torsion shafts - Bending on both sides - diameters of up to 1.1 times the top roller diameter are possible - Forged and hardened rollers with a hardness of 53-55 HRC - Low-maintenance, stable machine concept - Permanent lubrication of all bearings - Sturdy welded steel construction - electro-hydraulic hinged bearing for easy pipe removal - pressure gauge / pressure display for the rollers - Safety device (safety line with switch unit) - operating instructions Codpfx Agoylpz Hjkjpw * Special accessories included : - ROCCI height-adjustable center support * for large pipe diameters - ROCCI electro-motorized material feed table * motorized sheet feeding material support surface

Condition: excellent (used), Year of construction: 2020, 2020 BAYKAL BPMT-1525x30 CNC Punching Machine with Bosch MTX Control Cpjdpfx Asyml Ulsgksw CNC controller: Bosch MTX, Maximum press force: 30 t, Working range: 3000 x 1500 mm, Slider stroke number: 900/min, 20-station turret head, Tool rotation: indexable, Number of indexable tools: 4, Foot switch control, Oil tank capacity: 350 l, Sir pressure: 6 bar, Power: 15 kW, Power supply: 3x 380 V; 50 Hz, Dimensions (L x W x H): 6370 x 5710 x 2220 mm, Weight: 15000 kg, S/No: 27529.

Condition: good (used), functionality: fully functional, Year of construction: 2002, control type: manual, degree of automation: manual, actuation type: hydraulic, pipe diameter (max.): 60,90,115 mm, tube wall thickness (max.): 3 mm, number of axes: 3, working height: 700 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, operating pressure: 200 bar, pressure (max.): 200 bar, number of digital displays: 3, Equipment: CE marking, documentation/manual, emergency stop, quick-change device, Limpet coil roller hydraulic to form half round pipe from flat stainless steel strip and bending into wanted radius with spiral continuous. -Shafts output 80 mm -Interchangeable set of rollers on the shafts for the different size of pipe 60 mm , 90 mm , 115 mm -Coil holder for the reel metal strip with guide-way bench uncoiling and alignment the steel strip to the rolling machine -Pinching lower central roll adjustable to form the half pipe -Digital position readout to determine the bending diameter of the coil, the pitch of the coil, the half tube shape forming -hydraulic arm movable in 3 directions to set the pitch of the coil roll -Upper vertical support hydraulic operated to hold in position the formed diameter and collect the coils from diameter 700 to diameter 3000 mm Cpsdpfoyik Hcsx Agkow -Operator console electric with push buttons and digital position readouts for the coil length, the bending radius and the forming load. -Service manuals and operation books along with the machine

Condition: good (used), You are bidding on: a branded machine set – a folding machine from a renowned and well-known manufacturer – Schechtl HA and a guillotine shear RAS by Reinhard Maschinenbau Sindelfingen. Machine details: Folding machine: - Die rail bends cleanly – test possible on site - Angle display - Bending length slightly over 2.5m - Sheet metal capacity: 1.5 mm for steel – also suitable for aluminium, zinc, etc. - Standard die rail - Foot-operated closure - Current new price approx. €20,000 net Guillotine shear RAS: - Electrically operated guillotine shear up to 2mm steel – also suitable for aluminium, etc. - Cutting length: 2.5m - Extension table for special applications included in the price – can be mounted on the left side - Optional spare blades available - Adjustable depth gauge from the front Cpjdpfx Agoyqytqoksw - Many additional onsite tools and auxiliaries available as options - Machines can also be purchased individually Important: Optionally, you will also find a wide range of machines and equipment for sheet metal and steel processing on offer in our shop, including various rails, depth gauges – everything relating to bending and shearing, such as press brakes, guillotine shears, drilling machines, slip rolls, slitting and profiling machines, accessories (beading devices, round rollers for gutter fabrication, back gauges, etc.), as well as hand tools and spare parts from many top manufacturers in stock. Please feel free to contact me for any questions. You will receive an invoice in accordance with § 25a UstG, VAT is included in the invoice amount (margin taxation system). Free loading available – approx. weight: bending machine about 1900 kg, shear about 1600 kg. Inspection and testing are possible and encouraged by prior phone appointment. Payment in cash upon collection. Benefit from our experience and expertise – we are happy to advise you. Collection by the buyer (or a shipping company commissioned by the buyer) should take place within 10 days after the end of the auction. Location: 97249 Eisingen, approx. 3 minutes from the A3 and A81 motorways. Article number: Folding machine RAS 251009

Condition: new, angle steel/side length / mm double T-iron on the x-axis / mm U-iron on the x-axis / mm total power requirement 4/380 kW weight of the machine ca. 1645 kg required space 1500 x 1000 x 1400 mm The Gerd Wolff HPK-80 is a hydraulic profile and tube bending machine with 3 rollers. The machine is ideal for bending profiles, tubes and similar material. Model: HPK 80 Upper shaft diameter: Ø 80 mm Bottom shaft diameter: Ø 70 mm Roll diameter: Ø 245 mm Working speed: 7 m/min Motor power: 4.75 kW / 380 V Codpfx Asyk Im Eegkjpw Dimensions (L x W x H): 1500 x 1000 x 1400 mm Weight: 1645 kg Standard accessories Steel construction welded frame 3 Rolls are powered Hardened and ground shafts made of high tensile special steel Rolls are hardened and ground Horizontal and vertical working position Hardened standard rolls Mobile control panel 3 Axis mechanical lateral angle guide rolls Brake motor equipped for the precision bending Digital Read-Outs (2pcs) Optional Equipments Pipe, tube and profile bending rolls Hydraulic lateral guide rolls (2 axis) Automation with NC control

Condition: like new (used), Year of construction: 2019, tube diameter 28 mm Cpodjxcuhrjpfx Agkjw wall strength 2 mm bending radius min. 90 mm control 3D TubeSoft Slim total power requirement 3,5 kW

Condition: new, Year of construction: 2025, New machine immediately available Capacity: 1520 x 2.25 mm segment-split upper cheek rail -tool rest Cjdpoh S Uirefx Agkjpw -Adjustment of the upper beam by hand lever left/right

Condition: new, Year of construction: 2025, Capacity 1020 x 2,5 mm (ST37) Delivery of the upper beam by feet clamping High segments in the upper beam Bending and lower beam are segmented too RAL 7016 paint Manufacturing EU Cpjdjfifbbjpfx Agkew immediately available ex works Freight costs on request

Condition: new, Year of construction: 2025, Capacity 2020 x 2 mm (ST37) Delivery of the upper beam by hand lever left + right Slanted segments in the upper beam Continuous bending and lower beam rails RAL 7016 paint Cpedpfx Aefifa Asgkjw Manufacturing EU immediately available ex works Freight costs on request

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1992, number of digital displays: 4, Equipment: cone bending device, emergency stop, hardened rollers, 3-Roller Hydraulic Plate Bending Machine with Digital Displays Manufacturer: ROUNDO Model: PASS 230 Year of manufacture: 1992 Machine No.: 925194 Max. sheet width: 2000 mm Max. sheet thickness: 8 mm Pre-bending: 6 mm 2 powered rollers Cone bending device Drop-end bearing Hydraulic adjustment of rollers Hardened rollers Emergency stop Manual sheet support via spindle Cjdoyrh Edepfx Agkopw

Condition: new, functionality: fully functional, Year of construction: 2026, control type: manual, degree of automation: manual, actuation type: manual, working width: 1,250 mm, overall weight: 150 kg, warranty duration: 24 months, Box&Pan / Segment Bending / Folding Machine for Sheets RBP-125+ – Precision Bending in a Professional Edition Toolless removable bending fingers The box&pan / segment press brake, is an advanced device that enables the creation of complex profiles and precise bends that are not possible with a conventional roofing bending machine. Thanks to the segmented construction of each beam, our sheet metal folding machines offer versatility and precision, allowing for even the most demanding processing tasks. Versatility and Precision Our offer includes segment folding machines in three working lengths, making them suitable for various industries. The RBP-125+ model is the perfect solution for professionals who value quality and accuracy. The 700 mm working length allows for bending sheet metal up to 0.7 mm thick, making it indispensable for the most complex roofing projects, including standing seam processing and forming KARO tiles. Innovative Construction In the RBP series models, all three rows of bending teeth – clamping beam, bending beam, and fixed beam – are removable and adjustable, providing full flexibility in handling different materials. This solution ensures maximum precision and ease of work while allowing the machine to be adapted to the user's specific needs. Technical Specifications – Segment Folding Machine RBP-125+ with toolless removable bending fingers: Maximum bending capacity: Standard Steel: up to 0.7 mm Aluminum: up to 1.0 mm Copper and zinc: up to 1.0 mm Stainless: up to 0.4 mm Working length: 1250 mm Bending beam thickness: 15 mm Maximum bending angle: 160° Upper bending fingers clearance: 65 mm Lower bending fingers clearance: 45 mm Weight: 130 kg Cpedov Dvmijpfx Agkjw Ideal for Professionals The RBP-125+ segment folding machine is an excellent choice for roofers, sheet metal workers, and workshops engaged in metal processing. Thanks to its sturdy construction and high-quality craftsmanship, it ensures durability and reliability in everyday use. If you are looking for a tool that combines precision, durability, and functionality, our segment press brake will meet your expectations. 📞 📧 Contact us for more information and to find the perfect model for your needs!

Condition: used, Year of construction: 2002, sheet width 3050 mm plate thickness 3.0 mm ST Cpsdpfx Asxacfgogkjw pre-bending capacity 3.0 mm ST upper roll diameter 170 mm lower roll diameter 170 mm side roll diameter 180 mm Control konv. 0 380 V total power requirement 3.0 KW weight 4250 kg In good condition With new rubber-coated top roll (!!) Also suitable for bending non-ferrous metals Equipment: - Electro-hydraulic 3-roll bending machine - Asymmetrical roll arrangement - Electro-motor-driven side roll adjustment * Including digital position display - Manual bottom roll adjustment * Via hand crank - Including conical bending device * Inclined bottom roll and side rolls * Parallel alignment in any side roll position - Hardened rolls SAE 1050 CK 45 - Manual folding storage for removing closed pipes * Top roll must be raised before opening the storage (e.g., forklift/crane) - Safety device - Connection cable + connector - 4-way foot switch * 2 buttons for side roll movement (up/down) * 2 buttons for roll movement (left/right) * With 4x new foot switch covers - Operating instructions (English) * Special accessories included: - Brand new top roller with plastic/rubber coating * Suitable for bending non-ferrous metals * Such as copper and aluminum

Condition: as good as new (ex-display), Year of construction: 2022, sheet width 1070 mm plate thickness 4.0 mm pre-bending 3.0 mm roll length 1070 mm roll diam. toproll 110 mm bending speed 3.0 m/min engine output 2.2 kW weight 848 kg range L-W-H 2250 x 1000 x 1800 mm New price ~ 10.000 euros Exhibition machine - like NEW (!!) Equipment: - robust electro-mechanical round bending machine - 2x central rollers driven by electric motor (top & bottom roller) - right/left running of the rollers - top roller can be manually swiveled out, with folding bearing - manual delivery of the side roller Codpfsxacdpox Agkjpw - including conical bending device - asymmetrical roller arrangement - rollers with profile inlets - safety device (safety line with switch unit) - 1x freely movable control panel - operating instructions (ENG)