Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Lhjdpfx Aevf E Aveaben Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Maximum bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening dimensions: 19.5 x 65 x 111.5 cm Condition: Very good! Checked for proper operation. FLITS Rental & Sales service: every machine comes with a bundle of binding wire (120 wires). Need more binding wire bundles? Request a free quote. Lsdpfx Aasxnxntjbshn At FLITS Rental & Sales you choose speed, clarity, and reliability. We think along with you, respond promptly, and ensure you quickly have access to the right machine. You are welcome to inspect the machines at our location: Schoterlandseweg 94, 8413NE Oudehorne. Visits are possible by appointment, so we can take the time to properly inform you and show you the right machines. We are happy to assist you! Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste Waste processing

Condition: used, Year of construction: 2008, power: 4 kW (5.44 HP), The Strautmann PP 1207 Baler Potential recyclable materials: Cardboard, film, PET bottles, foam, cans, electronic scrap Technical specifications: Manufacturer: Strautmann Model: PP 1207 Lhjdpfsxftvyjx Aabsn Bale size (L x W x H): 1200 x 700 x 800 mm Bale weight: approx. 400 – 500 kg External dimensions (L x W x H): 1844 x 1067 x 2868 mm Transport height: 1970 mm Feed opening: 1145 x 430 mm Pressing force: 580 kN Throughput rate: 1 – 2 bales per hour Number of strapping channels: 4 Machine weight: 2,200 kg Power supply: 400 V / 50 Hz Power requirement: 4 kW Installation site: indoors / outdoors (covered) Noise level: below 80 dB(A) Year of manufacture: 2004 Baler rental possible (Lithuania, Latvia, Estonia, and Poland) PRICE ON REQUEST!

Condition: like new (used), Year of construction: 2019, functionality: fully functional, Amis ZBP 50 S Duo sawdust briquetting machine Year of production 2019 Load capacity up to 140 kg depending on material 3.800 working hours Briquettes Ø 50 mm Tank with a capacity of 1.2 m³ Roller with feeder Pre-ironing Screw conveyor Hydraulic pump motors, 7.5 kW each Lhjdpfeumwm Ssx Aabjn Fan cooling Sawdust level sensor in the tank Hydraulic oil tank 100 l SIEMENS control system Dimensions length x width x height 3000 x 2400 x 1700 mm Weight 2000 kg The price of the new machine is 39.800 Euro

Condition: used, Year of construction: 2004, The device is in working condition. Lodpfsw Tbfgjx Aabehn

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 80 t, DIXI 80 SLD horizontal press Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Lhedpfx Ajxg Iqusabsn Machine weight approx. 8,000 kg (without bale)

Condition: refurbished (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Ledpfx Aasu Th S Sobshn Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The can press was completely overhauled in our workshop. The press is in a very good condition and is sold with the 12 months OBM parts warranty. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-press 860 plus Year of manufacture: 2009 Pressing force: 418 kN Voltage: 400 V Max. bale weight: 430 kg (depending on material) Bale dimensions: 120 x 110 x 85 cm Machine weight: 2083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Fill opening dimensions: 120 cm x 65 cm x 85 cm Ledsxnxmvepfx Aabehn Condition: Very good! Checked for proper operation. FLITS Rental & Sales service: with every machine we supply a bundle of binding wire (120 wires).

Condition: used, Year of construction: 1991, power: 3 kW (4.08 HP), For sale or rent! Lsdpfx Ajxftrneabohn We are offering an HSM 155VL vertical baler for sale. Manufacturer: HSM Model: 155VL Year of manufacture: 1991 Motor power: 3.5 kW

Condition: used, Year of construction: 2022, total width: 950 mm, total height: 1,250 mm, total length: 1,800 mm, Empty weight: 390 kg Lhjdpfexd Rfisx Aabsn - Year: 2022 - Documentation available: No - CE marking present: Yes - Serial number: 546 - Transport dimensions: 1800mm x 950mm x 1250mm (l x w x h) - Transport weight [kg]: 390kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: as good as new (ex-display), Year of construction: 2022, Briquetting press for aluminium or steel chips Extremely high pressing force of 3,700 kg/cm² Large storage silo Briquette size: 60 x 40 mm Throughput: Lhodpfx Aow Ig Sujabjn Aluminium chips – up to approx. 70 kg/h Steel chips – up to approx. 100 kg/h Brass chips – up to approx. 100 kg/h *depending on feedstock Included: - Emulsion tray - Emulsion pump - Oil cooler

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, DIXI 80 SLS horizontal press Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Lsdpfx Aaoxgcznsbshn Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Lsdpfx Aeu Thkajabehn

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Lhedpfx Asvq Rtkoabon Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Year of construction: 2005, power: 7 kW (9.52 HP), FOR SALE / FOR RENT: VERTICAL BALER! (Rental available in Lithuania, Latvia, Estonia, and Poland) Technical Information: Manufacturer: HSM Model: HSM 500 VL Pressing force: 54–540 kN Lsdpfxsxftiyj Aabjhn Bale size: 1200 x 800 x 1200 mm Bale weight: approx. 500 kg Max. bale size: approx. 1200 x 800 x 1200 mm (W x D x H) Press chamber dimensions: 1200 x 800 x 1520 mm (W x D x H) Motor: 7.5 kW Year of manufacture: 2005 PRICE UPON REQUEST!

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Lodpexl Rqbjfx Aabohn Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Lodpfx Asv Amw Neabohn Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: ready for operation (used), Year of construction: 2010, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2010 Pressing force: 532 kN Voltage: 400 V Maximum bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening dimensions: 19.5 x 65 x 111.5 cm Condition: very good! Functionality checked. FLITS Rental & Sales service: with every machine we include a bundle of baling wire (120 wires). Do you require additional bundles of baling wire? Please request a complimentary quote. At FLITS Rental & Sales, you choose speed, transparency, and reliability. We think along with you, respond immediately, and ensure you quickly receive the right machine. You are very welcome to view the machines at our premises. We are located at Schoterlandseweg 94, 8413NE Oudehorne. Visits are by appointment, so we can take the time to advise you thoroughly and present the most suitable machines. We are happy to assist you! Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste processing Lhedpfx Aasxl A A Nsbjn

Condition: used, Year of construction: 2009, operating hours: 20,536 h, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, empty load weight: 16,000 kg, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: Ledou Thypspfx Aabohn The machine is currently in our workshop undergoing partial refurbishment. We expect the refurbishment work on the machine to be completed by the end of October, after which the machine will be tested and released for sale.

Condition: like new (used), Year of construction: 2018, functionality: fully functional, pressing force: 4 t, Perfect condition, newly repainted, fully tested, new wearing parts and oil, ready to use. We have 2 units. Lodpfxoxdk Dxo Aabohn

Condition: used, Year of construction: 2008, power: 3 kW (4.08 HP), The HSM V-Press 610 is a powerful baler designed for medium to large volumes of waste, making it ideal for commercial and industrial environments. This model combines high capacity, efficiency, and reliability, enabling effective compaction of a wide range of waste materials. Pressing force: 120 kN Drive power: 3 kW Filling height: 655 mm Filling opening (W x H): 800 x 495 mm Bale dimensions (L x W x H): 800 x 600 x 600 mm Bale weight: 100 kg Dimensions (W x D x H): 1198 x 823 x 1986 mm Machine weight: 540 kg Model series: V-Press Consumables: Strapping tape Processable materials: Plastic film, mixed paper, cardboard, punching waste Lhedpfoxfthvox Aabjn PRICE ON REQUEST!

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold with a 2-year warranty. Ledpfx Ajtvat Tjabohn

Condition: used, Year of construction: 2006, operating hours: 54,050 h, pressing force: 80 t, filling opening width: 1,020 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, oil tank capacity: 2,100 l, power: 94 kW (127.80 HP), empty load weight: 21,000 kg, Technical data baler: Manufacturer Paal Typ Konti 275 E Year of construction 2006 Hours of operation in total 54,050 hours Press power main press 80 tons at 300 bar Specific press capacity 9,7 kg/cm² Feed channel 1,600 x 1.020 mm (l x w) Throughput capacity under operating conditions 350 m³/hour Bale size 750 x 1,100 mm, length variable Driving motor 75 kW Connected load 94 kW Rated current 180 A Ljdpfxjxcxm Es Aabshn Tying system 4-fold vertical, fully automatic Bale weight up to 750 kg, depends on material Volume hydraulic oil tank 2,100 l SPS controller (manuf., type) Siemens Simatic S7-300 Operating panel (manuf., type) Siemens Multi Panel Transport dimensions only baler 11,152 x 2,152 x 3,000 mm (l x w x h) Machine weight baler approx. 21 tons Condition of the baler: The press and conveyor belt are in satisfactory working condition, see photo documentation. Further technical data and dimensions for the conveyor belt are not currently available. The plant is currently still in operation and is to be replaced by a larger press plant in the coming months. Scope of delivery: Bale press, bale chute, conveyor belt and machine documentation. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Dismantling and loading is the responsibility of the buyer. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2005, power: 7 kW (9.52 HP), SALE OR RENTAL OF VERTICAL BALER! (Rental available in Lithuania, Latvia, Estonia, Poland)! Technical information: Manufacturer: HSM Model: HSM 500 VL Press force: 54–540 kN Bale size: 1200 x 800 x 1200 mm Bale weight: approx. 500 kg Max. bale size: approx. 1200 x 800 x 1200 mm (W x D x H) Press chamber dimensions: 1200 x 800 x 1,520 mm (W x D x H) Motor: 7.5 kW Year of manufacture: 2005 PRICE ON REQUEST! Lhsdpfoxftg Ejx Aabsn

Condition: good (used), Year of construction: 2012, operating hours: 12,078 h, functionality: fully functional, pressing force: 88 t, filling opening width: 1,100 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 30,000 kg, oil tank capacity: 2,000 l, power: 98 kW (133.24 HP), volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2012 Total operating hours: 12,078 hours, as of September 2025 Pump operating hours 6,616 hours (effective pump running time) Number of bales pressed: 65,792 bales, as of September 2025 Main press force 880 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 120 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Drive power 2 x 45 kW frequency-controlled Connected load 98 kW Total current consumption 192 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h) Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h) Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t) Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Lhjdpfx Aexcngnjabsn Year of construction 2012 Drive power 7.5 kW Belt speed 0.05 – 0.4 m/second Length of feeding conveyor 6,000 mm Height of side wall from feeding conveyor 400 mm Length of incline conveyor 9,000 mm Height of side wall from incline conveyor 800 mm Length of gooseneck 1,500 mm Incline 30° Nominal width 1,800 mm Useful width 1,700 mm Belt quality EP-500/4 Steel cleats on the rubber belt 50 x 50 mm Hollow pin chain, pitch 125 mm, rollers 36 mm Height of drive axle above ground 4,284 mm Overall height of conveyor belt 5,765 mm Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h) Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h) Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.