Used roll benders (motor-driven) for sheet thickness over 14mm for sale (125)

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 73200 € 1383.48 € 2050 mm 20 mm 20 mm 16 mm 16 mm 12 mm 280 mm 280 mm 220 mm 1,5 / 5 m/min 16.5 kW 4350 mm 1700 mm 1850 mm 8550 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT (PRICES ON REQUEST): infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control Pjdpfjynmylsx Akfegk IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Pgjdpfx Akjh U Rzgefek Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1994, machine/vehicle number: 10659, roller (bottom) diameter: 300 mm, roller (top) diameter: 350 mm, working width: 3,000 mm, sheet thickness (max.): 25 mm, empty load weight: 24,000 kg, TECHNICAL DETAILS Number of rollers: 4 pcs Max. sheet thickness: 25 mm Max. working width: 3,000 mm Upper roller diameter: 350 mm Lower roller diameter: 300 mm MACHINE DETAILS Control: Conventional Dimensions & Weight Dimensions (L x W x H): 6,300 x 2,000 x 1,800 mm Unladen weight: 24,000 kg Pgedpfx Akjyua Ezefjk Transport packages: 1 pc.

Condition: used, functionality: fully functional, actuation type: hydraulic, roller (top) diameter: 420 mm, sheet thickness (max.): 25 mm, total length: 3,100 mm, Hydraulic cylinder Brand: Casanova Bending length: 3,100 mm Maximum bending thickness: 25 mm Top roller diameter: 420 mm The side rollers are raised parallel, without inclination. New control and command panel, installed and modified in 2003. Pgjdpfjydk D Hox Akfek Equipped with hydraulic flag and hydraulic side table. Pit dimensions: - 200x6800 mm - 555 mm depth

Year of construction: 1980, condition: good (used), with initial rounding Technische Daten:/ technical details Biegelänge / bending lenght 2000 mm max. Blechstärke / max. sheet thickness 20 mm Anbiegeleistung / initial rounding 15/11 mm Walzendurchmesser Unterwalzen / roll diameter below rolls 280 mm Oberwalzendurchmesser / diameter of the upper roll 300 mm Antriebsleistung Hauptantrieb / drive capacity main drive 16,2 kW Antriebsleistung Anstellantrieb Oberwalze / drive capacity upper roll 4,8 kW Antriebsleistung Anstellsntrien Unterwalze / drive capacity below roll 3,7 kW Gewicht ca. / weight ca. 14200 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Pgsdpfxskzg E Ae Akfjk Technical data, accessories and description of the machine are not binding.

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 3, roller (bottom) diameter: 300 mm, roller (top) diameter: 300 mm, side roll diameter: 280 mm, roller length: 3,100 mm, sheet thickness (max.): 15 mm, STANDARD EQUIPMENT * Side rolls move up and down orbitally via hydraulic pistons * Protected against overload * All rolls driven by hydromotor and planetary gearbox * Hydraulically opening head for easy removal of bent parts * Very easy operation with mobile control panel * Lower rolls positions easily read via two digital indicators * Welded steel construction body * SAE 1050 (CK 45) induction-hardened, hot-rolled steel shafts * Conical bending system with bearings * Hydraulic balancing system for parallel movement of shafts * Extended shaft ends for fitting profile- and pipe-bending rolls OPTIONAL EQUIPMENT * Top crane (elevator) for support during large diameter bending * Hydraulic side supports for large diameter bending * Ground and polished rolls for special applications Pgjdpew Sld Refx Akfjk * Rollers for profile bending * Infinitely adjustable hydraulic speed control * Electronic balancing system for parallel shaft movement TECHNICAL SPECIFICATIONS Bending Length: 3100 mm Pre-Bending: 10/13 mm Bending: 13/15 mm Top & Bottom Roll: 300 mm Side Roll: 280 mm Motor Power: 11 kW Bending Speed: 5 m/min Length: 5150 mm Width: 1500 mm Height: 1550 mm Weight: 9050 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 350 mm, roller (top) diameter: 350 mm, side roll diameter: 260 mm, roller length: 3,100 mm, sheet thickness (max.): 20 mm, STANDARD EQUIPMENT * Lower, top and side rolls move up and down linearly via pistons hydraulically attached to the frame * Protected against overload * Top and side rolls are driven by hydromotor and planetary gearbox (3-roll motor driven) * The position of the rolls can be easily read with three digital displays * Rolled parts are easily removed thanks to the hydraulically opening head and automatically lifting shaft * Very easy operation with mobile control panel * Welded steel construction frame * SAE 1050 (CK 50) induction hardened, forged or rolled steel shafts * Cone bending system * Centralized lubrication system * Hydraulic balancing system for parallel movement of the rolls (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620 -680) * Dual speed operation system OPTIONAL EQUIPMENT * Automation with NC and CNC controls * Top crane (elevator) for large diameter bending support * Hydraulic side supports for large diameter bending * Hydraulic sheet ejector system * Ground and polished rolls for special applications Pedpow Smdfsfx Akfogk * Stepless speed adjustment system * Electronic balancing system for parallel movement of the rolls (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length: 3100 mm Pre-bending: 12/16 mm Bending: 16/20 mm Top & Lower Roll: 350 mm Side Roll: 260 mm Motor Power: 23.5 kW Bending Speed: 1.5 - 5 m/min Length: 5350 mm Width: 1900 mm Height: 1950 mm Weight: 14,450 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 3, roller (bottom) diameter: 300 mm, roller (top) diameter: 300 mm, side roll diameter: 280 mm, roller length: 2,050 mm, sheet thickness (max.): 22 mm, STANDARD EQUIPMENT * Side rolls move up and down orbitally via hydraulic cylinders * Protected against overloading * All rolls are driven by hydromotor and planetary gearbox * Folded parts are easily removed thanks to the hydraulically opening head * Very easy to operate with movable control panel * Lower roll positions are easily read via two digital indicators * Welded steel body construction * SAE 1050 (CK 45) induction-hardened, hot-rolled steel shafts Podpfx Aew Slg Sskfsgk * Bearing-supported conical bending system * Hydraulic balancing system ensures parallel movement of shafts * Extended shaft ends for mounting profile and pipe bending rolls OPTIONAL EQUIPMENT * Upper crane (hoist) for support in large diameter bending * Hydraulic side supports for assistance in large diameter bending * Ground and polished rolls for special applications * Rollers for profile bending * Stepless hydraulic speed adjustment * Electronic balancing system for parallel shaft movement TECHNICAL SPECIFICATIONS Bending Length: 2050 mm Pre-bending: 16/20 mm Bending: 20/22 mm Top & Bottom Roll Diameter: 300 mm Side Roll Diameter: 280 mm Motor Power: 11 kW Bending Speed: 5 m/min Length: 4100 mm Width: 1500 mm Height: 1550 mm Weight: 7400 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 400 mm, roller (top) diameter: 400 mm, side roll diameter: 300 mm, roller length: 3,100 mm, sheet thickness (max.): 30 mm, STANDARD EQUIPMENT * The bottom, top, and side rolls move linearly up and down via hydraulic cylinders connected to the frame * Protected against overload * Top and side rolls are driven by hydromotor and planetary gearbox (3-roll motor drive) * The positions of the rolls can be easily read via three digital displays * Thanks to a hydraulically opening head and an automatically lifting shaft, bent workpieces can be easily removed * Very easy operation with mobile control panel * Welded steel construction frame * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts * Cone bending device * Centralized lubrication system * Hydraulic balancing system for parallel movement of rolls (Ø280 – 320 – 350 – 380 – 400 – 460) * Electronic balancing system (Ø500 – 550 – 580 – 620 – 680) * Dual-speed working system OPTIONAL EQUIPMENT * Automation via NC and CNC control * Top crane (elevator) support for large diameter bending * Hydraulic side supports for large diameter bending * Hydraulic sheet extraction system * Ground and polished rolls for special applications * Stepless speed adjustment system * Electronic balancing system for parallel roll movement (Ø280 – 320 – 350 – 380 – 400 – 460) TECHNICAL SPECIFICATIONS Bending Length: 3100 mm Pre-bending: 20/25 mm Bending Capacity: 25/30 mm Top & Bottom Roll: 400 mm Side Roll: 300 mm Pgodpfew Sl T Ssx Akfok Motor Power: 38.5 kW Bending Speed: 1.5 – 5 m/min Length: 5850 mm Width: 2250 mm Height: 2350 mm Weight: 20,200 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 550 mm, roller (top) diameter: 550 mm, side roll diameter: 450 mm, roller length: 3,100 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 50 mm, power: 70 kW (95.17 HP), warranty duration: 12 months, Equipment: emergency stop, foot remote control, hardened rollers, swiveling upper roller, STANDARD EQUIPMENT * The bottom and side rolls move up and down linearly via hydraulic pistons attached to the frame * Protected against overloading * The top and side rolls are driven by hydromotors and planetary gearboxes (all 3 rolls are motor-driven) * Easy roll position reading via three digital indicators * Easy removal of bent parts thanks to hydraulically opening head and automatically lifting shaft * Very user-friendly operation with the mobile control panel * Welded steel construction frame * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts * Cone bending system * Centralized lubrication system * Hydraulic balancing system for parallel movement of rolls (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620-680) * Dual-speed operation system OPTIONAL EQUIPMENT * NC and CNC control for automation * Top crane (elevator) for support when bending large diameters * Hydraulic side supports for large diameter bending * Hydraulic sheet ejector system * Polished and ground rolls for special applications * Infinitely variable speed adjustment system * Electronic balancing system for parallel roll movement (Ø280 -320 -350 -380 -400 -460) Pgsdpfxoxbzpte Akfsk TECHNICAL SPECIFICATIONS Bending Length : 3100 mm Pre-bending : 50/40 mm Bending : 40/35 mm Top & Bottom Roll : 550 mm Side Roll : 450 mm Motor Power : 70 kW Bending Speed : 1 - 4 m/min Length : 6750 mm Width : 2900 mm Height : 2950 mm Weight : 47,000 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 460 mm, roller (top) diameter: 460 mm, side roll diameter: 380 mm, roller length: 4,100 mm, sheet thickness (max.): 25 mm, power: 38.5 kW (52.35 HP), STANDARD EQUIPMENT * The lower, upper, and side rolls move linearly up and down via hydraulic pistons attached to the frame * Protected against overload * Upper and side rolls driven by hydromotor and planetary gearbox (all three rolls are motor-driven) * The position of the rolls can be easily read via three digital displays * Thanks to the hydraulically opening head and automatically lifting shaft, the bent workpiece can be easily removed Psdpfew Sl I Nox Akfsgk * Very easy operation with a movable control panel * Welded steel construction body * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts * Cone bending system * Centralized lubrication system * Hydraulic balancing system for parallel movement of the shafts (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620-680) * Dual speed operating system OPTIONAL EQUIPMENT * NC and CNC control automation * Overhead crane (elevator) for support during large diameter bending * Hydraulic side supports for large diameter bending * Hydraulic sheet removal system * Ground and polished rolls for special applications * Infinitely variable speed adjustment system * Electronic balancing system for parallel movement of the shafts (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length: 4100 mm Pre-bending Thickness: 16/20 mm Bending Thickness: 20/25 mm Upper & Lower Roll Diameter: 460 mm Side Roll Diameter: 380 mm Motor Power: 38.5 kW Bending Speed: 1.5 - 5 m/min Length: 6950 mm Width: 2300 mm Height: 2350 mm Weight: 29,500 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 280 mm, roller (top) diameter: 280 mm, side roll diameter: 220 mm, roller length: 2,550 mm, sheet thickness (max.): 16 mm, STANDARD EQUIPMENT * The upper, lower, and side rolls move linearly up and down via hydraulically actuated body-mounted pistons. * Protected against overload. * Upper and side rolls are driven by hydromotors and planetary gearboxes (all three rolls are motor-driven). * The positions of the rolls can be easily read through three digital display gauges. * The hydraulically opening head and automatic upward-lifting shaft allow easy removal of the bent workpiece. * Very user-friendly operation with a mobile control panel. * Welded steel construction body. * Rolls made from SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts. * Conical bending system. * Centralized lubrication system. * Hydraulic balancing system for parallel movement of the rolls (Ø280 - 320 - 350 - 380 - 400 - 460). * Electronic balancing system (Ø500 - 550 - 580 - 620 - 680). * Dual-speed operating system. OPTIONAL EQUIPMENT * Automation with NC and CNC control consoles. * Upper crane (hoist) for support in large diameter rolling. * Hydraulic side supports for large diameter rolling. * Hydraulic plate ejector system. * Ground and polished rolls for special applications. * Infinitely variable speed adjustment system. * Electronic balancing system for parallel movement of the rolls (Ø280 - 320 - 350 - 380 - 400 - 460). TECHNICAL SPECIFICATIONS Pedpfsw Smfcox Akfjgk Bending Length: 2550 mm Pre-bending: 10/12 mm Bending: 12/16 mm Upper & Lower Roll: 280 mm Side Roll: 220 mm Motor Power: 16.5 kW Bending Speed: 1.5 - 5 m/min Length: 4850 mm Width: 1700 mm Height: 1850 mm Weight: 9650 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 3, roller (bottom) diameter: 250 mm, roller (top) diameter: 250 mm, side roll diameter: 200 mm, roller length: 1,550 mm, working width: 1,550 mm, sheet thickness (max.): 15 mm, sheet thickness steel (max.): 15 mm, power: 7.5 kW (10.20 HP), warranty duration: 12 months, STANDARD EQUIPMENT * Side rolls move up and down orbitally via hydraulic pistons * Protected against overloading * All rolls are driven by hydromotors and planetary gearboxes * Easily removable bent parts thanks to a hydraulically opening top roll * Very easy operation with movable control panel * Lower roll positions are easily read via two digital displays * Welded steel frame construction * SAE 1050 (CK 45) induction-hardened, hot-rolled steel shafts * Conical rolling system with roller bearings * Hydraulic synchronisation system for parallel movement of shafts * Extended shaft ends to allow mounting profile and pipe bending rolls OPTIONAL EQUIPMENT * Top crane (elevator) for large diameter bending support * Hydraulic side supports for large diameter bending * Specially ground and polished rolls for custom work * Bending rolls for profiles * Infinitely variable hydraulic speed adjustment * Electronic synchronisation system for parallel movement of shafts TECHNICAL SPECIFICATIONS Bending Length: 1550 mm Pre-bending: 10/12 mm Pgodoxbzr Uspfx Akfsk Bending: 12/15 mm Top & Bottom Roll Diameter: 250 mm Side Roll Diameter: 200 mm Motor Power: 7.5 kW Bending Speed: 5 m/min Length: 3500 mm Width: 1200 mm Height: 1370 mm Weight: 3600 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 350 mm, roller (top) diameter: 350 mm, side roll diameter: 260 mm, roller length: 2,550 mm, sheet thickness (max.): 25 mm, STANDARD EQUIPMENT * Lower, upper, and side rolls are hydraulically actuated and move linearly up and down via body-mounted pistons * Protected against overload * Upper and side rolls are driven by hydromotors and planetary gearboxes (3-roller motor drive system) * Positions of the rolls can be easily read via three digital displays * The hydraulically opening head and automatically upward-moving shaft make it easy to remove the bent workpiece * Extremely easy operation with the mobile control panel * Welded steel construction frame * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts * Cone rolling system * Centralized lubrication system * Hydraulic balancing system for parallel movement of the rolls (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620 -680) * Dual speed operation system OPTIONAL EQUIPMENT * NC and CNC control for automation * Top crane (elevator) for support in large diameter rolling * Hydraulic side supports for large diameter rolling * Hydraulic sheet ejection system * Ground and polished rolls for special applications * Stepless speed adjustment system Pgedpfew Smb Rjx Akfsk * Electronic balancing system for parallel movement of the rolls (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Rolling Length: 2550 mm Pre-bending: 16/20 mm Bending: 20-25 mm Upper & Lower Roll: 350 mm Side Roll: 260 mm Motor Power: 23.5 kW Bending Speed: 1.5 - 5 m/min Length: 4850 mm Width: 1900 mm Height: 1950 mm Weight: 12,800 kg

Condition: new, Year of construction: 2025, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 320 mm, roller (top) diameter: 320 mm, side roll diameter: 240 mm, working width: 2,050 mm, sheet thickness (max.): 25 mm, Equipment: documentation/manual, emergency stop, foot remote control, hardened rollers, STANDARD EQUIPMENT * The lower, top, and side rolls move linearly up and down via hydraulic pistons fixed to the frame * Protected against overload * Top and side rolls are driven by hydromotor and planetary gearbox (3-roll motor driven) * Roll positions are easily readable via three digital indicators * Easy removal of the bent workpiece thanks to the hydraulically opening head and the automatically ascending shaft * User-friendly operation with a movable control panel * Welded steel construction frame * SAE 1050 (CK 50) forged or rolled steel shafts, induction-hardened * Conical bending system * Centralized lubrication system * Hydraulic balancing system for parallel movement of shafts (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620 -680) * Dual speed operation system OPTIONAL EQUIPMENT * NC and CNC control for automation * Overhead crane (elevator) for supporting large diameter bending * Hydraulic side supports for large diameter bending * Hydraulic sheet ejector system * Ground and polished rolls for special applications * Infinitely variable speed control system * Electronic balancing system for parallel movement of shafts (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length : 2050 mm Pedoxw Ebljpfx Akfegk Pre-bending : 16 / 20 mm Bending : 20 / 25 mm Top & Bottom Roll : 320 mm Side Roll : 240 mm Motor Power : 20 kW Bending Speed : 1.5 - 5 m/min Length : 4350 mm Width : 1800 mm Height : 1950 mm Weight : 10,500 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 3, roller (bottom) diameter: 300 mm, roller (top) diameter: 300 mm, side roll diameter: 280 mm, roller length: 2,550 mm, sheet thickness (max.): 18 mm, STANDARD EQUIPMENT * Side rolls move up and down orbitally via hydraulic pistons * Equipped with overload protection * All rolls are driven by hydromotors and planetary gearboxes * Hydraulic opening head allows easy removal of curved parts * Very easy operation with movable control panel * Lower roll positions can be easily read using two digital displays * Welded steel construction frame * SAE 1050 (CK 45) induction-hardened, hot-rolled steel shafts * Bearing-mounted conical bending system * Hydraulic balancing system provides parallel movement of shafts * Extended shaft ends to allow mounting of profile and pipe bending rolls Pgedpjw Slf Uofx Akfsk OPTIONAL EQUIPMENT * Overhead crane (elevator) for supporting large diameter bending * Hydraulic side supports for large diameter bending * Ground and polished rolls for special operations * Rolls for profile bending * Stepless hydraulic speed adjustment * Electronic balancing system for parallel shaft movement TECHNICAL SPECIFICATIONS Bending Length: 2550 mm Pre-Bending: 12/16 mm Bending: 16/18 mm Upper & Lower Rolls: 300 mm Side Rolls: 280 mm Motor Power: 11 kW Bending Speed: 5 m/min Length: 4600 mm Width: 1500 mm Height: 1550 mm Weight: 8400 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 460 mm, roller (top) diameter: 460 mm, side roll diameter: 380 mm, working width: 2,050 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 50 mm, power: 38.5 kW (52.35 HP), warranty duration: 12 months, STANDARD EQUIPMENT * The lower, upper and side rolls move up and down linearly via hydraulic cylinders attached to the body * Protected against overload * The upper roll and side rolls are driven by hydromotor and planetary gearbox (all 3 rolls are motor driven) * Three digital displays allow easy reading of roll positions * Hydraulic opening head and automatic lifting shaft enable easy removal of the bent workpiece * Easy operation with mobile control panel * Welded steel construction body * SAE 1050 (CK 50) induction hardened, forged or rolled steel shafts * Conical bending system * Centralized lubrication system * Hydraulic synchronization system for parallel movement of shafts (Ø280 -320 -350 -380 -400 -460) * Electronic synchronization system (Ø500-550-580-620-680) * Dual-speed operation system OPTIONAL EQUIPMENT * Automation with NC and CNC control * Top crane (elevator) for support in large diameter bending * Hydraulic side supports for large diameter bending * Hydraulic sheet removal system * Ground and polished rolls for special applications * Infinitely variable speed adjustment system * Electronic synchronization system for parallel movement of shafts (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length: 2050 mm Pre-bending: 35 / 40 mm Bending: 40 / 50 mm Upper & Lower Roll Diameter: 460 mm Pjdpsxd S T Uefx Akfjgk Side Roll Diameter: 380 mm Motor Power: 38.5 kW Bending Speed: 1.5 - 5 m/min Length: 4850 mm Width: 2300 mm Height: 2350 mm Weight: 19,800 kg

Condition: new, Year of construction: 2025, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 380 mm, roller (top) diameter: 380 mm, side roll diameter: 300 mm, working width: 3,100 mm, sheet thickness (max.): 25 mm, Equipment: documentation/manual, emergency stop, foot remote control, hardened rollers, swiveling upper roller, STANDARD EQUIPMENT * The lower, upper and side rolls move up and down linearly, operated by hydraulic pistons connected to the frame * Protected against overloading * Upper and side rolls are driven by hydromotors and planetary gearboxes (all three rolls are motor-driven) Pgodpfxjxw Ecvo Akfjk * The positions of the rolls can be easily read via three digital displays * Rolled parts can be easily removed with hydraulically opening head and automatic lifting shaft * Very easy operation with mobile control panel * Welded steel construction frame * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts * Conical bending system * Centralized lubrication system * Hydraulic balancing system for parallel movement of the shafts (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620-680) * Dual-speed working system OPTIONAL EQUIPMENT * Automation with NC and CNC control * Overhead crane (elevator) to support large-diameter bending * Hydraulic side supports to assist with large-diameter bending * Hydraulic sheet ejector system * Ground and polished rolls for special applications * Infinitely variable speed adjustment system * Electronic balancing system for parallel movement of the shafts (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length : 3100 mm Pre-bending Capacity : 16/20 mm Bending Capacity : 20/25 mm Top & Bottom Roll Diameter : 380 mm Side Roll Diameter : 300 mm Motor Power : 31.5 kW Bending Speed : 1.5 - 5 m/min Length : 5850 mm Width : 2250 mm Height : 2350 mm Weight : 19,200 kg

Condition: new, Year of construction: 2025, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 380 mm, roller (top) diameter: 380 mm, side roll diameter: 300 mm, roller length: 4,100 mm, sheet thickness (max.): 16 mm, STANDARD EQUIPMENT * Lower and side rolls are connected to the body by hydraulic pistons and perform vertical linear movement * Protected against overload * Top and side rolls are driven by hydromotors and planetary gearboxes (3 roll motor drive) * Roll positions are easily read via three digital indicators * Hydraulic opening head and automatic upper shaft lift allow easy removal of rolled parts * Easy operation using a movable control panel Psdpfxsw Smc Ie Akfogk * Welded steel construction frame * SAE 1050 (CK 50) induction-hardened forged or rolled steel shafts * Cone bending system * Centralized lubrication system * Hydraulic balancing system for parallel shaft movement (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620-680) * Dual-speed operating system OPTIONAL EQUIPMENT * Automation via NC and CNC control * Overhead crane (elevator) to support large diameter bending * Hydraulic side supports to assist with large diameter bending * Hydraulic sheet ejection system * Ground and polished rolls for special applications * Stepless speed adjustment system * Electronic balancing system for parallel shaft movement (Ø280 -320 -350 -380 -400 -460) TECHNICAL SPECIFICATIONS Bending Length : 4100 mm Pre-bending : 10/12 mm Bending : 12/16 mm Top & Bottom Roll Diameter : 380 mm Side Roll Diameter : 300 mm Motor Power : 31.5 kW Bending Speed : 1.5 - 5 m/min Length : 6950 mm Width : 2250 mm Height : 2350 mm Weight : 22000 kg

Condition: new, Year of construction: 2025, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 400 mm, roller (top) diameter: 400 mm, side roll diameter: 300 mm, working width: 2,550 mm, sheet thickness (max.): 40 mm, Equipment: documentation/manual, emergency stop, foot remote control, hardened rollers, STANDARD EQUIPMENT Pjdpfx Akoxw Ebxjfsgk * Upper, lower, and side rolls are linearly moved up and down by hydraulically actuated pistons attached to the frame * Protected against overload * Upper roll and side rolls are driven by hydromotors and planetary reducers (3 roll motor drive) * The position of the rolls can be easily read with three digital indicators * The hydraulically opening head and the automatically lifting shaft allow the bent part to be removed easily * Very easy operation with movable control panel * Welded steel construction body * SAE 1050 (CK 50) induction-hardened, forged or rolled steel shafts * Conical bending system * Centralized lubrication system * Hydraulic balancing system for parallel movement of rolls (Ø280 -320 -350 -380 -400 -460) * Electronic balancing system (Ø500-550-580-620-680) * Dual speed operation system OPTIONAL EQUIPMENT * NC and CNC control for automation * Top crane (elevator) to support large diameter bending * Hydraulic side supports for large diameter bending * Hydraulic sheet removal system * Ground and polished rolls for special applications * Stepless speed adjustment system * Electronic balancing system for parallel shaft movement (Ø280-320-350-380-400-460) TECHNICAL SPECIFICATIONS Bending Length: 2550 mm Pre-Bending: 25/30 mm Bending: 30/40 mm Upper & Lower Roll Diameter: 400 mm Side Roll Diameter: 300 mm Motor Power: 38.5 kW Bending Speed: 1.5 – 5 m/min Length: 5350 mm Width: 2250 mm Height: 2350 mm Weight: 17,800 kg

Year of construction: 2018, condition: good (used), Make: FACCIN Type: 4HEL 3590 Control: Siemens TOUCH Year: 2018 Specifications Metric US Standard Rolling width 3500 mm Rolling thickness 3x toproll Ø 80 mm Rolling thickness 5x toproll Ø 110 mm Rolling thickness prebending 90 mm Top Roll Ø 900 mm Top Roll Ø 900 mm Bottom Roll Ø 800 mm Side roll Ø 600 mm Number of rolls 4 Rolling speed 0-6 Adjustiment lower roll 0-200 mm/min. Adjustment side rolls 0-400 mm/min. Top support yes Side supports yes Number of driven rolls 2 Power 90+75+9 kW Pgedokvm Nfepfx Akfjk Dimensions (Estimate) Length 4430 mm Width 8800 mm Height 11000 mm Weight 178000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, sheet thickness: 45bending length: 3100upper roll diameter: 480 Technical specifications: - Hardened and polished rolls - Complete body made of ST-52 Steel - Machine have 4 rolls and designed for symmetrical working principle - Hydraulic powered cover for easy material extracting - Digital readout for side rolls (2 digital readout) - Side rolls are free for rotation and upwards downwards movements are hydraulic powered - Top and bottom rolls are driven by hydraulic and gearbox. Bottom roll’s vertical movements are hydraulic powered - Separate control panel form machine - Conic bending device - In accordance for CE norms Pgedpfed Ab Rcox Akfsk Options: - variable speed of rotation EURO 5.858,-- - metarial feeding table EURO 5.100,-- - oil coiler STD. - center support EURO 18.750,-- - side supports EURO 15.150,-- - Automatic material extractor - PLC control - CNC control - Automatic material loading system - Changeable top roll - Adjustable bottom roll support system (for customer’s special requests) We have many references!

Condition: new, bending length: 3100sheet thickness: 45upper roll diameter: 510 Technical specifications: - Hardened and polished rolls - Conic bending device - Digital readout for side rolls - Complete body made of ST-52 Steel - Portable control panel separated form machine - Rolls are mounted with bearings - Top roll cover, openable and closeable by hydraulic, controlled from control panel. - All rolls are driven by hydraulic motor and planetary gearbox - Side rolls upwards downwards movements are hydraulic powered Options: - variable speed of rotation EURO 5.858,-- - metarial feeding table EURO  - oil coiler STD. Pgodsd Ab Snepfx Akfjk - center support EURO 18.750,-- - side supports EURO 15.150,-- We have many references!

Condition: new, sheet thickness: 45bending length: 3100upper roll diameter: 510messurements (LxWxH): 6300 x 2300 x 2590prebending: 35weight approx.: 33500 Technical specifications: - Hardened and polished rolls - Complete body made of ST-52 Steel - Machine have 4 rolls and designed for symmetrical working principle - Hydraulic powered cover for easy material extracting - Digital readout for side rolls (2 digital readout) - Side rolls are free for rotation and upwards downwards movements are hydraulic powered - Top and bottom rolls are driven by hydraulic and gearbox. Bottom roll’s vertical movements are hydraulic powered - Separate control panel form machine - Conic bending device - In accordance for CE norms Options: - variable speed of rotation EURO 7.000,-- - metarial feeding table EURO 3.700,-- - oil coiler EURO 800,-- - center support EURO 9.500,-- - side supports EURO 10.200,-- Pgjdpfx Aod Ab N Uokfek - Automatic material extractor - PLC control - CNC control - Automatic material loading system - Changeable top roll - Adjustable bottom roll support system (for customer’s special requests) We have many references!

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2017, machine/vehicle number: 25498, roller (bottom) diameter: 320 mm, roller (top) diameter: 320 mm, side roll diameter: 260 mm, working width: 2,070 mm, sheet thickness (max.): 25 mm, TECHNICAL DETAILS Sheet width: 2,070 mm Sheet thickness: 25 mm Bending capacity: 18 mm Top roller diameter: 320 mm Side roller diameter: 260 mm Lower roller diameter: 320 mm MACHINE DETAILS Total power supply: 26 kW Dimensions & Weight Pedpfx Ajygw Ikskfogk Space requirement: approx. 4,700 x 2,000 x 2,200 mm Machine weight: approx. 8,100 kg EQUIPMENT Hydraulic lateral roller adjustment Conical bending device 2 driven rollers Hardened rollers Hydraulic drop-end bearing Mobile control panel Foot switch Safety device CE marking