Used Cold Rolling Machine for sale (69,353)

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Dsdpfxjuz If Ne Ai Sscn Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Thread rolling machine, cold rolling machine, thread forming machine, profile rolling machine Manufacturer PEE-WEE, Type P 24 Q Serial No. LC2403099, Year of manufacture 2004 Rolling force, max. 24 tons Tool diameter, max. 200 mm Rolling spindle diameter 69.85 mm Tool bore diameter 70 mm (nominal diameter) Receiving length, tool length, max. 180 mm Workpiece diameter, max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 RPM Hydraulic motor power approx. 3 kW Rolling drive motor power 5.5 kW Mains connection 400 Volt, 50 Hz - Swiveling rolling spindle for thread through-rolling - Rolling spindle speed in 4 stages via gear change - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons Good condition Dcedjh A S Htspfx Ai Sjn Plunge rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating the workpiece up to the nominal diameter. The thread length is a maximum as long as the rolling tools are wide. Through-rolling tools: If the thread length is greater than the rolling tool width. Through-rolling tools have 3 sections - the inlet, the calibrating section, and the outlet. Grooved rollers have no pitch and are swiveled with the helix angle of the profile to be rolled. Helix rollers differ from grooved rollers by having a pitch in the profile. The sum of the helix angle and the swivel angle results in the helix angle in the workpiece.

Condition: used, Year of construction: 2015, overall weight: 16,000 kg, total height: 2,200 mm, total length: 4,410 mm, total width: 2,600 mm, GROB C6-A – Cold Rolling Machine Technical Data: Gear Module: up to approx. 2.3 Dsdpfx Aijz E Ra Hj Sscn Gear Diameter: approx. 8–80 mm Max. Clamping Diameter: approx. 315 mm Power: 25 kW Weight approx.: 16,000 kg Dimensions (LxWxH) approx.: 4410 x 2600 x 2200 mm Year of construction: 2,015 Terms of payment: 100% prepayment before pick-up Terms of delivery: From foundation under power: No

Year of construction: 1998, condition: excellent (used), machine/vehicle number: ExCello Serial Number 3888, MICHIGAN Rotoflo Type 3237 Cold Forming Machine. Original Serial Number: 4590 ExCello Serial Number 3888 Djdpfxjfnk Ehs Ai Sjcn New 1975 rebuilt by ExCello late 1990’s Country of Origin: USA For the coldforming of profiles for serrations (straight or angular), spiral teeth, oil grooves, threads and knurls. Capacity: Maximum slide stroke 1065 mm Maximum rack length 915 mm Maximum profile diameter 50 mm Maximum profile length 125 mm Standard module range 0.3 to 1.25 Motor size 15 kW Hydraulic tank capacity 1000 l Overall floorspace width of machine 5014 mm Width of machine 2768 mm Depth with outboard support 4165 mm Height 2000 mm Approximate weight of machine 11,700 kgs Complete with: Hydraulically operated outer support assembly to accommodate part length universal headstock, Universal rack holding feature.

Condition: used, Year of construction: 1987, rolling capacity max. NA t workpiece diameter 38 mm workpiece length 500 mm total power requirement 24 kW weight of the machine ca. 10 t dimensions of the machine ca. m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features * KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. * Originally, external gears were formed on the machine using pinion cages (no. of teeth = 25), Ø approx. 32 mm x 14 mm long, workpiece Ø approx. 80 x 80 mm long. * Various accessories: * Separate switch cabinet. * Separate hydraulic unit, 900 l. * Coolant device in the machine. * Control panel with malfunction message in plaintext, etc. Roto Flo machines are ideal for mass production of smaller gears/profiles. The coldforming process is a lot faster and more economical than other chip removing methods. Workpieces are clamped between 2 live centres and 2 synchronous opposed directional coldforming racks simultaneously engage the workpart and start rotation. During rotation, the profile is formed successively within one stroke. In the calibrating zone, the profiling and surfacing performance of the tool are optimised. Profiles do not require a run-out. The coldforming process requires a rigid and heavy duty construction of the machine, which ensures the required precision over the years. Between 25,000 and 100,000 working cycles can be performed with one set of racks, also for serrations. Dcodpfjt Hw D Dsx Ai Son Condition : Very good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We always have a good selection of gear machines available. Please let us know what you need.

Condition: used, Thread rolling machine UPWS 25. Dedpjzd Rf Nofx Ai Sjcn

Condition: used, Year of construction: 2011, Control Siemens Sinumerik 840D sl centre height 1.150 mm z-axis 1.559 / 307 mm x-axis 16 - 80 mm Swing circle diameter 92 mm roll spindle turning speed range 0 - 3.000 U/min Rolling mill roll clearance - axial 0,025 mm feed speeds infinitely variable 0 - 30.000 mm/min rapid traverse 30.000 mm/min Swivel angle range ±3,2 ° Max. speed - main spindle 375 U/min piston stroke 400 mm Dcsdpfxjzdk Iko Ai Sjn diameter of piston 90 mm with effective piston area 63,6 cm² In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Year of construction: 1980, condition: used, Rolling mill in working condition, designed for the production of hot-rolled metal products: reinforcing bars, rounds, squares, angles, flats, channels, and beams. Maximum initial blank diameter: 180 mm. Dcsdpfxsz Eq Nuo Ai Ssn It consists of a three-roll roughing stand with a diameter of 600 mm and five finishing stands with a diameter of 320 mm, as well as a calibrating three-roll stand with a diameter of 320 mm. High productivity. Cantilever-type rolling rolls are used. They are inexpensive to manufacture and can be quickly replaced when switching from one type of rolled product to another. Location: Ukraine, Sumy. Dismantling and loading are included in the price.

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: EVO, controller model: EVO 4 AXIS 15", number of rollers: 4, roller (top) diameter: 300 mm, roller diameter: 300 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 1,250 mm, sheet thickness (max.): 22 mm, sheet thickness steel (max.): 22 mm, sheet thickness stainless steel (max.): 20 mm, sheet thickness aluminum (max.): 30 mm, overall weight: 17,000 kg, total length: 5,500 mm, total width: 2,000 mm, total height: 2,100 mm, power: 18.5 kW (25.15 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4roll hydraulic plate bending machine MODEL M3035 , year 2024 machine as new with warranty included Planetary dual pre-pinch plate prebend SPECIAL FRAME WITH TOP ROLL REDUCED SIZE 300 MM TO ACHIEVE SMALLER BENDING DIA 330 MM Performance Capacity: Plate width 3000 mm plate thickness rolling 22mm pre-bend 20 mm minimum rolling diameter ID 330 mm usefull surface width on the rollers 3100 mm Power electric motor 18.5kw on hydraulic unit Vac 400/50 -480/60 Dsdpfjy Tbf Iex Ai Socn Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted on wheels with joysticks and readout CNC programmable 4 axis controller touch screen 15” Setup virtual infinite rolling programs with teach-in mode and cad/cam operator interface --- Hydraulic motorized driven the central rolls Pre-pinch load adjustable for pre-bend Drop-end top roll front open unloading closed shells Re-rolling system for welded shells calibration. Safety and emergency stop Manuals and schematics machine dimension 5500x2000x2100 mm -weight 17ton --- Additional accessories available with the machine to agree on request nr.1 central support hydraulic 2.2 ton capacity to support large shell dia up to 4,5 meters id nr.1 side support hydraulic left side 2.2 ton double arm nr. 1 side support hydraulic right side 2.2ton double arm

Condition: good (used), functionality: fully functional, Year of construction: 2004, machine/vehicle number: 4roll 2000x6 mm, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 155 mm, roller (top) diameter: 165 mm, side roll diameter: 120 mm, roller diameter: 165 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 600 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 8 mm, sheet thickness brass (max.): 10 mm, sheet thickness copper (max.): 10 mm, overall weight: 2,200 kg, total length: 3,400 mm, total width: 1,150 mm, total height: 1,100 mm, power: 2.21 kW (3.00 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, emergency stop, hardened rollers, -roll 2000x6 mm plate bending machine Davi model MAX2017 year 2004 used plate roll in working condition, Planetary dual pre-pinch Performance Capacity: Plate width 2000 mm plate thickness 6 mm pre-bend 5 mm Djdpfszy N Afex Ai Sscn minimum rolling diameter ID 350 mm rollers length 2050 mm Upper roll 165 mm Pinch roll 155 mm Side rolls 120 mm Power electric motor 3 kw on hydraulic unit Vac 400/50 mm Installed configuration Rollers surface hardened high strength Conical plate rolling, cone bending Hydraulic commands via leverage distributors Infinitely variable speed control Digital position readout --- Hydraulic driven motorized the central rolls Pre-pinch pressure adjustable for pre-bend Drop-end front open to unload closed shells Re-rolling system for calibration of welded shell Safety and emergency stop machine dimension 3400x1150xH 1100 mm -weight 2200kg

Condition: refurbished (used), ROLLFORMING MACHINE PRODUCING SQUARE PROFILES WITH 5 TONES OF TOOLS MADE IN ITALY Dcedpfxofgl Aqj Ai Sjn

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, machine/vehicle number: plate roll Faccin, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 180 mm, roller (top) diameter: 200 mm, side roll diameter: 160 mm, roller diameter: 200 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 700 mm, sheet thickness (max.): 8 mm, sheet thickness steel (max.): 8 mm, sheet thickness stainless steel (max.): 8 mm, sheet thickness aluminum (max.): 10 mm, sheet thickness brass (max.): 12 mm, sheet thickness copper (max.): 12 mm, overall weight: 3,700 kg, total length: 3,500 mm, total width: 1,100 mm, total height: 1,000 mm, power: 5.52 kW (7.51 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 3, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 2000 X 8 MM MODEL 2020B4 year 2020 capacity 2000x8 mm Plate roll hydraulic linear guideways Machine in excellent working condition Bending capacity -Plate width : 2000 mm -Rolling plate thickness 8 mm - Prebend thickness 6 mm Rolls dimensions: -Useful length 2050 mm -Upper roll 200 mm -Lower roll 180 mm -Side rolls 160 mm Electric motor 5,5Kw Vac 400/50 • Hardening of the 4 rolls high strength surface • Central rolls driven with hydraulic motors and gear units • Conical bending attachment side rolls tiltable to form cones Dcjdpfx Aiezy Nv Eo Son • Opening front hydraulic drop-end to unload the closed shell. • Variable speed working roll bending rotation hydraulic speed fast/slow. • Console electric on wheels with centralized commands joysticks and 3 digital readout. • Digital readouts of the rolls position bending and pre-bending repeatability. • Dimension 3500 x1100 x H 1000 mm - weight 3700kgs

Condition: used, Year of construction: 2001, functionality: fully functional, Profile Bending Machine SAF Curvatrici (TUWI) DS 60 HV – Top Condition & Huge Tool Package Description: For sale is a high-quality profile bending machine, type SAF Curvatrici (TUWI) DS 60 HV, from the first owner. The machine was purchased new by us in 2001 and has been in our possession ever since. It is fully operational and can be demonstrated under power after prior consultation. Special highlight – Modernized control system (08/2019): The control system was completely overhauled and modernized by a specialist company in August 2019. Now, 10 different feed sequences can be programmed. After a programmed value is reached, the next value is automatically approached by pressing the button again (value input in ascending order). Dedpfx Aisz Ix Ukj Sscn Technical data & equipment: • Shaft diameter: 50 mm (for all three axes) • Acceptance height: 115 mm • Additional equipment from factory: 2 RCD correction rollers for bending angle iron (R/L). The original, lateral and height-adjustable shafts (38 x 250 mm) are also included. • Special modification for transport: Specially manufactured base frame for transport including four height-adjustable support plates. • Additional device for angle iron: A 10 mm thick plate was mounted on the top side. An additional hydraulic cylinder can be attached here, which pushes the vertical flange extremely close to 90° during bending (adjustable pressure depending on the angle). Note: The cylinder is not included in the standard price, but can be requested separately. Enormous scope of supply (Extremely many tools included!): The biggest advantage of this offer is the extremely extensive tool package, which is completely included in the price: • Standard tools: Complete set according to the machine’s scope of supply • 18 different roller sets: According to the list from Ø 8 mm to Ø 33.7 mm • Special tools for angle iron (according to the list) • Special tools for flat steel (light & heavy axis) • Special tools for square and rectangular tubes • Special tools for diagonal square material • Documentation: Original operating manual is fully available Note: The machine will only be sold as a complete package together with the complete tool set according to the attached list. Sales and delivery conditions: • Pricing: Ex works (net, plus VAT). • Logistics: The disassembly, loading and collection must be organized and carried out by the buyer himself or by a forwarding agent commissioned by him. Technical specifications according to available documents. Subject to prior sale.

Year of construction: 2008, condition: ready for operation (used), We are offering this ready-to-use Roll-o-Matic roller die-cutting machine, roller size 0.932/3000, manufactured in 2008. Dcedpfx Aiez Ag Ukj Sen Usable roller width: 3000 mm. The upper roller has a diameter of 320 mm and is equipped with a PA or cast nylon cutting sleeve. The roller gap can be adjusted independently on both sides and is equipped with an absolute value display for the roller gap. Operating modes: setup operation; semi-automatic operation; fully automatic operation with a light barrier and time control. Includes 5 conveyor belts, a counter, and additional equipment: support rollers for the lower roller to reduce deflection under high load. Chain drive and more powerful motor. Includes control buttons on both sides. If you have any questions or require more information, please send us a message or call us.

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: NC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: SIEMENS, controller model: PLC, number of rollers: 4, roller (bottom) diameter: 150 mm, roller (top) diameter: 150 mm, side roll diameter: 140 mm, roller diameter: 150 mm, roller length: 2,050 mm, working width: 2,000 mm, roller height adjustment: 18 mm, working height: 800 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 4 mm, sheet thickness aluminum (max.): 6 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, overall weight: 2,800 kg, total length: 3,800 mm, total width: 1,200 mm, total height: 1,100 mm, power: 3 kW (4.08 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 4, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BENDING MACHINE NC HYDRAULIC MODEL 2000X6 MM / 4 MM PREBEND PROGRAMMABLE AUTOMATIC ROLLING NC 4 AXIS CONTROLLER Capacity: plate width 2000 mm thickness rolling 6 mm pre-bending 4 mm minimum diameter of rolling D= 180 mm depending on the plate thickness and strength Rollers length 2050 mm Upper roll size 150 mm Dcodpow Hpzwofx Ai Sjn Lower roll size 150 mm Rollers hardened surface high strength smooth surface finishing suitable for rolling stainless steel quality plates Conical plate rolling attachment Rotation electric powered on central rollers for bending traction of the plate Pre-pinch load variable upon plate thickness and strength Console electric commands push buttons with digital readout of the 4 rollers on the screen. NC programmable 4-axis to set automatic rolling with save 200 programs in memory front side hydraulic opening to remove the rolled shells speed slow/fast variable safety installation with emergency stop. Instruction manuals for operation and service. Layout mm 3800x1200xH1100 mm Weight 2800 Kgs

Condition: used, Year of construction: 2007, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, year of last overhaul: 2022, We are offering this used KÖNIG ECO TWIN roll production line, manufactured in 2007. Model: ECO TWIN Type: 800-(DB800)-K6-SCHN6/B-(DA) Serial number: 07.0.0782 Dodpfx Aoznm S Hji Sscn Year of manufacture: 2007 Power: 8 kW Frequency: 50 Hz Rated voltage: 3 × 400 + N V Rated current: 15 A The system has been fitted with new belts and is in perfect, fully functional condition. It was used by us solely as a backup system and was therefore only used very rarely. We acquired and overhauled the system approximately two years ago. The system is immediately available and can be collected directly after arrangement. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: new, Year of construction: 2026, total width: 750 mm, total length: 2,900 mm, total height: 1,160 mm, warranty duration: 12 months, overall weight: 400 kg, Compact roll forming equipment for producing metal rainwater downpipes This portable roll forming machine is designed for the production of rectangular metal downspouts and rainwater downpipes from pre-painted or coated sheet steel. The machine progressively forms a flat metal strip into a finished rectangular profile suitable for residential, commercial and industrial rainwater drainage systems. The dimensions and geometry of the finished downpipe can be manufactured according to the customer’s technical requirements. The roll tooling is designed for a specific rectangular profile, taking into account the required width, height, corner shape, surface pattern, material thickness and connection type. The machine is suitable for manufacturers of: rectangular metal downspouts; rainwater downpipes; roof drainage systems; gutter and downspout components; roofing accessories; façade and sheet-metal products; custom cold-formed metal profiles. Its compact size and relatively low weight make it suitable for small workshops, roofing companies and production sites where a large stationary roll forming line is not required. Custom profile dimensions The finished profile is produced according to the customer’s drawing, sample or technical specification. The machine is therefore supplied as a custom rectangular downspout roll former, configured for the required finished product. The basic production process is: Decoiler → Roll forming system → Manual saw cutting Main advantages Compact and portable construction Custom tooling for the required downpipe size Production directly from coated sheet steel Suitable for pre-painted and galvanized material Gradual roll forming with controlled material deformation Low installed motor power Simple operation and maintenance Suitable for small-batch and regular production Finished products can be cut to the required length Reduced dependence on purchased ready-made downpipes Suitable for workshops with limited production space Material The standard configuration is designed for coated sheet steel with a thickness of approximately 0.4–0.5 mm. Depending on the agreed configuration, the machine may process: pre-painted steel; galvanized steel; polymer-coated sheet steel; other thin sheet-metal materials after technical approval. The exact material grade, tensile strength, thickness and coating must be specified before the roll tooling is designed. Technical specifications: Machine type Portable roll forming machine Finished product Rectangular metal downspout / downpipe Profile dimensions According to customer specification Material Coated sheet steel Material thickness Approx. 0.4–0.5 mm Forming speed Approx. 3–8 m/min Main motor power 3 kW Dcjdpfx Aozrnxcoi Son Transmission Gear and sprocket drive Auxiliary forming elements Polyurethane wheels Cutting system Manual circular saw Machine dimensions Approx. 2860 × 730 × 1160 mm Machine weight Approx. 400 kg Electrical supply 380 V, 50 Hz, 3-phase* Compact machine design This makes it suitable for: roofing contractors; rainwater system manufacturers; sheet-metal workshops; gutter and downpipe producers; building component manufacturers; small and medium-sized production facilities; companies producing custom roofing accessories. Scope of supply A custom set of roll forming tools will then be designed for the required product.

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, paper width (max.): 1,800 mm, Unwind diameter: 1,000 mm Rewind diameter: 800 mm Max. speed: 400 m/min Friction shafts for 3 and 6 inch Hydraulic lift at the unwind station Splicing table Web edge control Tidland knife holders, 20 pieces Semi-automatic knife setting system from Tidland Recipe management Laser positioning We will also dismantle and load the machine onto a truck or sea container at our own expense. Dcodpfx Aeywl D Nei Sen

Condition: new, Year of construction: 2026, Automatic Roll Forming Line for Light Gauge Steel Frame Production This automatic roll forming line is designed for manufacturing Light Gauge Steel (LGS) and Cold Formed Steel (CFS) structural profiles used for steel frame houses, modular buildings, commercial buildings and prefabricated construction systems. The production line automatically performs feeding, leveling, punching, roll forming, profile marking and hydraulic cutting according to digital production data. It is an ideal solution for manufacturers of: Light Gauge Steel structures Steel frame houses Prefabricated buildings Modular buildings Tiny houses Commercial steel structures Residential steel framing Cold formed steel construction systems Flexible Machine Configuration The roll forming line can be supplied in two different configurations depending on production requirements. Fixed Profile Machine Designed for manufacturers producing one profile size with maximum productivity and simplified machine setup. Multi-Profile Roll Forming Machine An adjustable roll forming system capable of producing several profile widths on one machine by changing the roll forming configuration. This solution provides greater production flexibility while reducing investment costs compared with purchasing multiple dedicated production lines. Complete Automatic Production Process The machine automatically performs the following operations: Coil feeding Strip leveling Servo punching Hole punching Slot punching Service hole punching Roll forming Profile identification marking Hydraulic cutting to length Finished profile discharge The production line is designed to work with professional steel frame design software. The operator imports production data generated from a building design into the machine control system. Based on this information the machine automatically manufactures every structural member including: wall studs tracks floor joists roof trusses rafters beams structural reinforcements Each component is produced with the correct length, punching pattern and identification marking required for final assembly. Automatic Profile Marking Each profile can be automatically marked during production. Typical marking information includes: Profile number Wall identification Member position Assembly reference Project identification Automatic marking significantly simplifies profile sorting and speeds up on-site assembly. Instead of manually identifying every component, installers receive a complete production kit with every profile clearly identified. Automatic Punching System All punching operations are synchronized with the roll forming process to achieve high accuracy and repeatability. Main Advantages Fully automatic production Computer controlled manufacturing Automatic profile marking Servo punching system Hydraulic cutting High dimensional accuracy Reduced material waste Fast production Flexible profile sizes Suitable for custom house projects Reduced manual labour Easy assembly thanks to profile identification Applications Technical Specifications Typical options include: Single-profile roll forming machine Dedpfx Aezrt Ivsi Sjcn Multi-profile adjustable machine Automatic profile marking Servo punching Hydraulic cutting Automatic decoiler Hydraulic decoiler Computer control system Production management software compatibility

Condition: good (used), functionality: fully functional, Year of construction: 2010, machine/vehicle number: SY 330 -075, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: Akyapak, number of rollers: 4, roller (bottom) diameter: 300 mm, roller (top) diameter: 330 mm, overall weight: 9,100 kg, total length: 4,585 mm, total width: 1,610 mm, total height: 1,840 mm, input voltage: 400 V, input current: 35 A, input frequency: 50 Hz, Equipment: documentation/manual, emergency stop, foot remote control, hardened rollers, The sale includes a 2-meter longitudinal welding station equipped with an Oerlikon MIG 500 A welding unit, with all equipment in full working order. Also included are a lifting table for material handling to the plate rolling machine and a work platform. The plate rolling machine is in good condition and can be put into production immediately. The machine is currently operational, and inspection and test runs can be arranged upon request. Dodpfx Aijzzdahe Sscn With the inclusion of the longitudinal welding station, this package provides a complete solution for manufacturing tubes and special pipe sections to customer-specified diameters, with lengths of up to 2 meters.

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, Equipment: documentation/manual, ORT Italia Netting Machine CE certified Model RP 18/U Year 2012 Siemens SIMATIC OP17 CNC control panel Reference: F24 €8,500, as is Dcedpozb Imaefx Ai Ssn

Condition: used, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 3, roller (top) diameter: 450 mm, side roll diameter: 410 mm, sheet thickness (max.): 40 mm, sheet thickness steel (max.): 40 mm, sheet thickness stainless steel (max.): 30 mm, sheet thickness aluminum (max.): 50 mm, sheet thickness brass (max.): 50 mm, sheet thickness copper (max.): 50 mm, overall weight: 23,000 kg, input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, hardened rollers, Plate bending machine 3 ROLL HYDRAULIC MODEL 3000 X 40 MM - YEAR 1997 PLATE BENDING ROLL PLANETARY DESIGN PYRAMID DUAL PRE-PINCH Nameplate Bending capacity -Plate width : 3000 mm -Rolling plate thickness: 40 mm -Prebend thickness: 30 mm --- minimum rolling ID 550 mm depending on plate thickness and width Rolls dimensions: -Useful length 3100 mm -top roll D 450 mm -side rolls D 410 mm Accessories installed: Central upper support hydraulic control to hold the plate formed into large diameters Side arm hydraulic to support the large diameter being formed Conical bending attachment with hydraulic control of the angle setting for cone rolling, cone bending stopper hardened pad swing-down on the drop-end of the machine. Technical data Rolls hardening induction treatment, high strength surface of the 3 rolls Power driven total on the 3 rolls with axial gearbox and direct drive hydro-motor each roll Console electric on wheels with centralized commands joysticks and digital readout. Digital readouts of the rolls position bending and pre-bending. Re-rolling system for welded shells rounding. Dodpfsz H N Ifox Ai Secn Opening front side hydraulic drop-end to unload the closed shell. Variable speed working roll bending rotation hydraulic speed fast/slow. Voltage supply 3 phase Vac, electric power 40 Hp.

Condition: good (used), Year of construction: 2011, For Sale: Konig Industrie Rex I 6/5 row Range: 33 - 95 grams Year of construction: 2011 Very well maintained Diagrams available + Hopper with oil system + Spreading belts Please note: the power unit is missing. (New price of the power unit approx. €10,000) However, it is possible to connect this Rex directly to a proofer that does have a power unit. Transport can be arranged. Inspection possible on-site. Dsdpfew Edmfex Ai Sjcn Price: €35,000,- EXW If you have any questions or comments, please do not hesitate to contact us. Sincerely, Leo Holland

Condition: good (used), Year of construction: 2019, Rollfix 700 automatic rolling machine - used - year of manufacture 2019 - computer control with touchscreen Dcodpjz Hv U Ejfx Ai Son - automatic flour dispenser - automatic dough rolling - production machine - inspected and cleaned - stainless steel construction and housings - collection from warehouse / transport option available - price on request

Condition: excellent (used), functionality: fully functional, Year of construction: 2024, actuation type: electric, roller diameter: 90 mm, working width: 1,270 mm, sheet thickness (max.): 3 mm, overall weight: 520 kg, power: 1.1 kW (1.50 HP), input voltage: 400 V, rotational speed (max.): 6 rpm, type of input current: three-phase, Equipment: cone bending device, emergency stop, foot remote control, hardened rollers, swiveling upper roller, sheet metal roll bending machine BOLUK BM 1270 x 90 - 2.5 mm NEW! for sale. manufacturer: BOLUK 1270X90mm year of manufacture: 2024 Bending Length: 1270 mm Bending capacity: 2.5 mm Roller diameter 90 mm - SAE 1050 certified high tensile steel rollers - Wire grooves at the ends of the rollers (4/6/9) mm - Manually adjustable rear roller - Mobile control panel with foot pedal - Precision bending with brake motor - Conical bending device - Manually foldable end - Cast iron main frames Bending speed 6m / min Motor power 1.1 kW 50Hz 380v Wire groove diameter 4/7/10 mm Djdpfx Aoxhub Aoi Sscn Machine dimensions 1850x700x1200 mm Weight 520 kg