Used Hydraulic Cold Press for sale (27,432)

Condition: good (used), Lechner IV B Hydraulic Bookbinding Press The machine is ready to operate. The press has a built-in hydraulic unit. Four stations. Ibodozv Nlxepfx Aiyjb Irreplaceable in bookbinding for the production of books, pads, etc.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Ijdpfszuzw Djx Aiyobb Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: like new (used), Year of construction: 2018, machine/vehicle number: STHP 80KN, functionality: fully functional, pressing force: 8 t, table width: 300 mm, total length: 200 mm, total width: 510 mm, total height: 1,320 mm, overall weight: 110 kg, 1 Hydropneumatic press type STHP 80 kN Bmcbfntr with two-hand operation - floor model with and base frame The compact and handy table model has a hydropneumatic drive with pressure intensifier, which can increase the punching force by up to 5 times. The punching cylinder is pressurized with oil by the pressure intensifier during the working stroke and therefore has a purely hydraulic punching stroke. The return stroke is performed directly with compressed air. The adapter that can be screwed into the piston rod of the working cylinder makes it possible to install special tool holders. Ibsdpfjt Rhb Iox Aiysb

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, type of input current: three-phase, pressing force: 5 t, operating speed: 300 mm/s, table width: 450 mm, table length: 320 mm, throat depth: 180 mm, oil tank capacity: 9 l, overall weight: 270 kg, Hydraulic Press Atsugi AP-5-KL Used Load Range: 20-50 (kN) Stroke (mm): 150 Lower Speed ​​(Approach Fast Speed: 350 (mm/s) Ibedpovbdpysfx Aiyjb Lower Speed ​​(Under Pressure Slow Speed: 36mm/s Rise Speed ​​250 (mm/s) Working Area Open Height: 250mm Open Depth: 180mm Table Size: 450x50mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/9L Total Weight (kg) 270 Body Size ​ Height (mm) 986 Width (mm) 485 Depth (mm) 920

Year of construction: 1986, condition: ready for operation (used), OFFERED FOR SALE DUE TO OVERCOMPLETION: Well maintained second hand hydraulic press brake, brand LVD, equipped with front support Model PPN 125/4000 S630 Built in 1986 TECHNICAL CHARACTERISTICS Max. pressure force 1250kN Max. oil pressure 310bar Max. working length 4000mm Max. passage between the uprights 3150mm Max. stroke of the ram 150mm Distance table / ram 350mm Unloading 250mm Width of table 180mm Closing speed 90mm/s Working speed 7mm/s Return speed 55mm/s Motor power 10kW Approximate weight 13500kg Steered axes Y1,Y2,X Ibsdpfxsr Ezv Ue Aiysb STURING CNC TOUCH S-630 (New 2019) Very user-friendly Full touch screen (10") control with 2D graphic simulation controlled axes: Y,X,R cnc backgauge X-duo - R back gauge with 2 movable fingers ADDITIONAL TOOLS F10 H180 26° 7x508mm + 1x550mm in sections Multi-V M90 L4000mm Asking price excluding transport costs (for buyer). Note: only serious bids will be responded to!

Condition: good (used), Rolong Hydraulic Book Spine Calibration Press This machine is used to calibrate the spines of book blocks or brochures. Ibsdpfx Aiezt H T Ijysb After calibrating the spine, its thickness is equal to the thickness of the block in the groove. This process is performed after the books have been sewn. 380V power supply Manufacturer: Gantenbein, Switzerland

Condition: used, CNC press brake WEINBRENNER, type EGP 80 Die-bending machine (DEFECTIVE) Serial No. 1257G, Year of manufacture 1991 Press force 80 tons Working length 1300 mm Stroke 260 mm with Cybelec DNC 94 PS with back gauge Weight 8800 kg Isdpfxez A Ia Se Aiysbb without tools, tooling system probably TRUMPF Machine is not functioning, control system does not boot up. The parameters are probably lost.

Condition: like new (used), functionality: fully functional, overall weight: 200 kg, Year of construction: 2000, pressing force: 2 t, throat depth: 150 mm, Hydraulic Press Atsugi Model AP-2-M Used Load Range: 5-20 (kN) Stroke (mm): 150 Down Speed: 60 (mm/s) Up Speed ​​73.8 (mm/s) Working Area Open Height: 250mm Ibsdpfx Aiovbdyfsysb Open Depth: 150mm Table Size: 450x320mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/6L Total Weight (kg) 200 Body Size ​ Height (mm) 987 Width (mm) 505 Depth (mm) 735

Condition: used, New hose assembly machine, DAEWOO type DA5100-HC Hydraulic hose crimping press, workshop hose crimping press for crimping hose connections Serial no. 25DW06440ALE01, Year of manufacture 2025 Crimping force: 500 tons Crimping range: Ø 1/4 to 2" (15-63 mm) Maximum die opening: approx. 75 mm Pump flow rate: 6 L/min Operating capacity: 200 pieces/hour Hydraulic pressure: 315 bar Motor power: 3 kW Mains connection: 400 volts, 50 Hz - 2 operating modes: manual and automatic - Operation via buttons or foot switch - Crimping stroke adjustment via knurled screw - Short changeover times for conversion to other hose diameters - Crimping jaws are easily inserted into guides and held in place by magnetic force - 10 tool sets, crimping dies (Ø 15, 19, 23, 26, 31, 36, 41, 47, 55, 63 mm) - Cabinet base with hydraulic unit Space requirement L x W x H: 700 x 500 x 1200 mm Weight: 270 kg Isdpfsz Afhpjx Aiysbb New - unused

Condition: excellent (used), Year of construction: 1969, functionality: fully functional, pressing force: 160 t, stroke length: 650 mm, table width: 1,200 mm, table length: 800 mm, working height: 600 mm, Equipment: safety light barrier, Lasco TSP 160S press A press in very good technical condition for sale from a liquidated stamping shop in Poland Modernized in 2019. Isdpfx Asv E Rd Eoiyjbb New Simatic S7 control system and new electrical cabinet. Optical barriers installed. Possibility to check the machine in operation - The press is still connected to the power supply. Lasco TSP 160S press A press in very good technical condition for sale from a liquidated stamping shop in Poland Modernized in 2019. New Simatic S7 control system and new electrical cabinet. Optical barriers installed as well. Possibility to check the machine in operation - The press is still connected to the power supply.

Condition: new, Year of construction: 2026, functionality: fully functional, power: 22 kW (29.91 HP), input voltage: 400 V, input current: 30 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 315 t, stroke length: 800 mm, operating speed: 120 mm/s, reverse speed: 100 mm/s, table width: 1,160 mm, table length: 1,260 mm, table height: 600 mm, ram plate width: 1,160 mm, ram plate length: 1,260 mm, distance table to ram: 1,250 mm, clearance between the columns: 1,160 mm, retraction force: 30 t, oil tank capacity: 510 l, total length: 2,000 mm, total width: 1,250 mm, total height: 3,500 mm, overall weight: 13,000 kg, Equipment: CE marking, documentation/manual, safety light barrier, YQ32-315T Hydraulic Press This series of presses are general-purpose hydraulic presses, widely used in machinery manufacturing, automotive, motor, electrical appliance, light industry and other industries. They are suitable for metal processing procedures including drawing, bending, flanging, cold extrusion and blanking. The machines also perform straightening, press fitting, as well as compression molding of powder products, abrasive products, plastic products and insulating materials. The working pressure, pressing speed and stroke can all be adjusted within the specified parameter range according to process requirements. Equipped with an independent power unit and electrical control system, the press adopts centralized push-button control and supports three operation modes: manual, semi-automatic and automatic. It is available with two pressing modes: pressure setting and stroke setting. Ijdpsy Uiyvefx Aiysbb Operation Sequence: Motor start → Main cylinder piston rapid no-load downstroke → Low-speed pressurization → Pressure holding (holding time adjustable) → Pressure relief → Slide return stroke → Work stop → Total stop Mainframe The mainframe adopts a vertical three-beam four-column structure, consisting of an upper beam, a slide, and a lower beam connected by four columns, which are fastened with nuts to form a closed rigid frame. All major structural components of the mainframe are fabricated from welded steel plates using CO₂ gas shielded welding. After welding, the entire frame undergoes vibration stress relief to eliminate internal residual stresses. Key components are machined on advanced equipment such as gantry milling machines, large floor-type boring and milling machines, and large precision lathes, ensuring high overall accuracy of the machine. The mainframe is pre-tensioned using hydraulic nuts. The slide is connected to the piston rod of the main cylinder and moves up and down guided by the columns. T-slots are provided on the lower surface of the slide and the upper surface of the movable worktable for die mounting. The columns are made of high-quality 45 carbon steel with hard chrome plating on the surface; the column guide sleeves are made of composite material, offering excellent wear resistance and self-lubricating properties.

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, pressing force: 100 t, stroke length: 500 mm, operating speed: 200 mm/s, reverse speed: 200 mm/s, table width: 750 mm, table length: 560 mm, ram plate width: 530 mm, ram plate length: 400 mm, total length: 1,900 mm, total width: 1,200 mm, total height: 3,200 mm, overall weight: 5,040 kg, Equipment: documentation/manual, Hydraulic press PYE 100 S1M with ejector. Manufacturer: Werkzeugmachinen GmbH Zeulenroda (Germany), year 1990. Specifications: Maximum pressing force 100 t. Operating pressure 16 MPa. Maximum ejector force 40 t. Ejector piston stroke 200 mm. Upper table 530x400 mm. Lower table 750x560 mm. Clear opening 800 mm. Cylinder stroke 500 mm. Downward speed 200 mm/s. Upward speed 200 mm/s. Power requirement 17 kW. Weight 5040 kg. Height 3200 mm, length 1900 mm, width 1200 mm. Iedpfx Aijygtzyoyobb

Condition: good (used), Year of construction: 2015, functionality: fully functional, pressing force: 2,500 t, table width: 2,500 mm, table length: 5,000 mm, total length: 8,000 mm, total width: 8,000 mm, total height: 9,000 mm, overall weight: 55,000 kg, Equipment: safety light barrier, LOIRE SAFE Hydraulic Press – High-Performance System for Toolmaking and Heavy-Duty Forming Ibedsyw Ah Espfx Aiyjb This high-performance hydraulic press in a robust 4-column gantry design has been specifically engineered for demanding applications in toolmaking (tryout/spotting) as well as for large-format forming processes. The stress-relieved, annealed welded construction ensures maximum rigidity and long-term process stability. The machine is equipped with three main cylinders featuring multi-cylinder parallel control, achieving high repeat accuracy within ±0.1 mm. Its powerful hydraulic system, based on Bosch Rexroth components, operates at a maximum working pressure of approximately 450 bar, enabling precise and forceful processing. Control is provided via a Siemens S7-317F PLC, combined with servo-controlled axes (Rexroth MLC) and visualization via Siemens WinCC. This setup allows for fully programmable press cycles, storage of tool parameters, and user-friendly operation with diagnostics and fault monitoring. In terms of safety, the press is comprehensively equipped: light curtains at the front and rear (Category 4), ram parallelism monitoring, emergency stop with defined response time, and optional two-hand operation ensure maximum operational safety. The system is CE-compliant and meets current safety standards. Features include a hydraulic, three-section draw cushion, a hydraulic ram cushion, as well as a movable table with approximately 4,000 mm stroke. The machine is complemented by a DIN-standard ram plate and integrated cutting impact damping for challenging forming processes. Toolmaking (Tryout / Spotting)

Condition: used, Year of construction: 1999, functionality: fully functional, total length: 8,120 mm, total height: 2,300 mm, Vertical Hydraulic Press FAMAD HSKG 6m – Number of loading zones: 3 Dimensions of a single loading zone: – Loading height: 1140 mm – Length of battens in one zone: 1530 mm – Maximum batten width: 150 mm Ibedpjyuylnefx Aiysb – Maximum length of glued elements: 3120 mm – Installed power: 3 kW – Number of cylinders per zone: - 3 pcs 50x100 mm - 3 pcs 80x100 mm – External dimensions (L x W x H): 8120x1000x2300 mm – Machine weight: 4800 kg

Year of construction: 1970, condition: ready for operation (used), machine/vehicle number: 55703, SANDT 410 Hydraulic Swing-Arm Cutting Press – 18 tonnes Price: €3,650 excluding VAT Delivery terms: EXW Son en Breugel, the Netherlands Very clean and robust German hydraulic swing-arm cutting press manufactured by J. Sandt AG, Pirmasens. Suitable for die-cutting materials such as leather, rubber, plastics, foam, felt, textiles, gasket material, cork and cardboard. Technical specifications * Manufacturer: J. Sandt AG * Model: 410 * Serial number: 55703 Iodszqhdispfx Aiyobb * Year of manufacture: unknown, presumably late 1960s * Cutting force: 18 tonnes * Working table: 900 × 450 mm * Swing-arm pressure plate: 550 × 350 mm * Measured clearance: approximately 110 mm * Mechanical height adjustment by handwheel * Electrical supply: 380 V, 3-phase, 50 Hz The machine is in clean, used condition and has been repainted. The lower cutting plate and the aluminium upper plate show signs of use. Machining and surface-grinding of both the lower and upper plates can be carried out upon request for an additional €250. The machine can be inspected and tested by appointment. Loading onto the buyer’s transport can be arranged. All information is provided to the best of our knowledge and is subject to verification.

Condition: ready for operation (used), machine/vehicle number: 13214814, functionality: fully functional, power: 11 kW (14.96 HP), type of input current: three-phase, pressing force: 250 t, year of last overhaul: 2010, Equipment: documentation/manual, Hydraulic press, 250 tons – fully functional, manufactured in former East Germany (DDR), model VEB Wema Zeulenroda. Isdezbyxnopfx Aiyobb

Condition: good (used), Year of construction: 1982, Press force: max. 200 kN Safety distance: 100mm Post-travel: max. 10 mm Motor power: 3 kW Ibjdozvfp Hepfx Aiyjb

Condition: excellent (used), functionality: fully functional, overall weight: 800 kg, Year of construction: 1995, pressing force: 10 t, operating speed: 260 mm/s, stroke length: 200 mm, table length: 440 mm, table width: 430 mm, type of input current: AC, Equipment: safety light barrier, Manufacturer JAM Model HYP-1000 Model year 1995 Capacity 98KN (10t) Stroke 200mm Nyitott magasság: 395mm asztal méret 440 × 430mm Ijdpfx Ajwcqc Usiyobb Shock hole φ32 × 60L mm ram aproaching speed:260 mm/s ram pressure speed:19 mm/s ram return speed: 219mm/s With light safety device voltage 3-phase 200v 1,5kw press body mass: 800kg operation oil: 43liter ​ Height (mm) 1395 Width (mm) 700 Depth (mm) 1170

Condition: like new (used), Year of construction: 2023, functionality: fully functional, PLEASE READ CAREFULLY!!! THIS OFFER IS EXCLUSIVELY FOR EUROPEAN END CUSTOMERS, AND THE FIRST INQUIRY MUST INCLUDE COMPLETE CONTACT INFORMATION. THANK YOU. The forging line consists of a hydraulic 1500-ton forging press, an induction unit with 1200 kW, and a robot with a load capacity of 300 kg. So far, prototypes have been manufactured; however, the line was actually designed for series production, which has not yet taken place. The line was built and installed in 2023. The technical specifications are as follows: Hydraulic press 1500 tons (year of manufacture 2023) SIEMENS control system - Pressing force: 1500 tons - Retraction force: 120 tons - Downward stroke: 300 mm/s - Pressing stroke: 100 mm/s - Upward stroke: 300 mm/s - Installation height: 3,000 mm - Ram stroke: 1,500 mm (!) - Ram size: 1,600 x 1,600 mm - Table size: 1,600 x 1,600 mm - Ejection force / 1 position: 40 tons - Stroke: 600 mm - Ejection speed: 250 mm/s - Return speed: 250 mm/s - Stroke: 400 + 400 mm - Traverse speed: 200 mm/s - Ram positions: 3 positions Including a 1200 kW induction unit (year of manufacture 2023) MITSUBISHI control system - 1200 kW / 450 Hz induction unit for billets - Coil size: Ø 215 / Ø 150 mm, two sets of coils - Material feeding system Including a Kawasaki robot (6 axes) – Model: ZX300S-D- (year of manufacture 2023) - Max. load capacity: 300 kg - Max. reach: 2500 mm Sample images of the machines are attached. Ijdezvnpiopfx Aiyebb

Condition: refurbished (used), Year of construction: 1993, machine/vehicle number: 20658, functionality: fully functional, power: 22 kW (29.91 HP), input voltage: 400 V, input current: 63 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 320 t, stroke length: 250 mm, operating speed: 7 mm/s, reverse speed: 70 mm/s, table width: 250 mm, table length: 4,800 mm, table height: 980 mm, throat depth: 305 mm, ram plate length: 4,500 mm, distance table to ram: 500 mm, clearance between the columns: 3,760 mm, oil tank capacity: 350 l, total length: 6,300 mm, total width: 2,300 mm, total height: 3,475 mm, overall weight: 22,500 kg, year of last overhaul: 2026, Equipment: documentation/manual, safety light barrier, Hydraulic press brake LVD PPI 320/40 S840W Year of manufacture: 1993 Year of refurbishment: 2026 Serial number: 20658 Technical specifications: Force: 3200 kN Working length: 4500 mm Distance between uprights: 3760 mm Stroke: 250 mm Distance table – ram: 500 mm Gap: 305 mm Table width: 250 mm Approach speed: 80 mm/s Working speed: 7 mm/s Return speed: 70 mm/s Weight: 22500 kg Motor: 22 kW Oil capacity: 350 l Dimensions (L x W x H): 6300 x 2300 x 3475 mm New 2026 S840W controller • S840W: 15” touch screen – Graphic controller with free online service assistance Iedpozktg Aefx Aiyobb • Axes: Y1, Y2, X, V • V: CNC crowning table • 2 front supports • Hydraulic clamping of the top tool in LVD classic 15 tool holder Tooling included: E15 H150 78° L3000mm D15 H150 78° L4500mm F15 H150 26° L4500mm H15 H150 L2500mm R15 H150 78° L4500mm V20 H130 30° L3500mm V20 H130 78° L3000mm V40 H130 78° L4500mm V60 H130 78° L4500mm V90 H130 78° L2500mm M130 Multi-V L4500mm (90/40/24/16/10)

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, pressing force: 500 t, table width: 1,500 mm, table length: 2,000 mm, oil tank capacity: 1,200 l, total length: 3,500 mm, total width: 2,400 mm, total height: 6,000 mm, overall weight: 45,000 kg, installation height: 1,000 mm, Equipment: safety light barrier, HIDROLIKSAN HCFP – 500-ton Hydraulic Tryout/Testing Press for Toolmaking and Forming Technology The machine is a tryout/testing press for tools in the field of forming, deep drawing and toolmaking. It is fully functional, ready for operation and can be inspected and tested while powered on. The press frame consists of a 4-column construction, a generous working area and a hydraulic system with REXROTH pump technology. The control system is a SIEMENS S7-1200 with a touch panel and extensive parameterization options. Scope of delivery & Accessories Tool sliding and lifting ball system GÜTHLE Hydraulic foot pedal (GÜTHLE) Roller bolster/carrier console 10 t (GÜTHLE) 4-channel tool clamping system (length 1500 mm, 2 t per channel) Complete REXROTH hydraulic unit Air cooler Condition of the machine Fully functional Hydraulic system is leak-free and runs smoothly Control system & electrical components in good condition Mechanically sound, no visible damage The machine is in assembled condition and can be demonstrated while powered on. Press force: Nominal force: 500 t Max. press force at 250 bar: approx. 510 t Dimensions & Weight: Overall dimensions approx.: 3500 × 2400 × 6000 mm Total weight: approx. 45,000 kg Working area: Table area: 2000 × 1500 mm Column spacing (internal): 2000 × 900 mm Installation height: 1000 mm Stroke: 800 mm (linearly adjustable via linear measuring system) T-slots available (mounting positions to be defined by customer) Hydraulic system: Main cylinder Number: 2 Piston Ø: 340 mm Rod Ø: 280 mm Auxiliary/planing cylinder Number: 2 Piston Ø: 120 mm Rod Ø: 70 mm Draw cushion Force: 150 t Cylinder: 2 × Ø 310 × 210 mm Stroke: 400 mm Pumps and tank Pump: REXROTH axial piston pump, 100 ccm, approx. 150 L/min Hydraulic tank: 1200 L Oil system: 1000 L filling capacity Speeds Forward stroke: 120 mm/s Return stroke: 150 mm/s Working/pressure stroke: 12 mm/s Control & Safety: Control system SIEMENS S7-1200 + ET200S 12" Touch Panel Schneider Electric Operating modes: Two-hand automatic mode Setup mode Single stroke Stroke without draw cushion Deep drawing mode with draw cushion Measuring & safety components Linear measuring system Novatechnik (63 Bit) for ram and draw cushion Light barriers SICK at the front and rear (height: 1050 mm) Side protective grilles with limit switches Remote maintenance via Ethernet possible Mobile control panel Ibjdpfex D Tv Dex Aiyeb International Note Block (DE/EN) German Dismantling, deinstallation, loading and transport are the sole responsibility of the buyer and at the buyer’s cost and risk. The seller does not provide equipment, personnel or loading assistance. Collection only by prior appointment. English Dismantling, deinstallation, loading and transport are the sole responsibility of the buyer and at the buyer’s cost and risk. The seller does not provide personnel, equipment, lifting devices or loading assistance. Pickup must be scheduled in advance. Sale is EXW (Incoterms 2020). Location: Saxony/ Germany

Condition: good (used), Year of construction: 1982, Hydraulic press JKM Kindsmüller UPS 100 E – 110 tons For sale: a hydraulic workshop/industrial press, JKM Kindsmüller, type UPS 100 E. Technical specifications: * Pressing force: 1100 kN (110 tons) * Operating pressure: 283 bar Isdpjy Unl Rjfx Aiyebb * Stroke of upper piston: 700 mm * Year of manufacture: 1982 * Control system overhauled/renewed in 1992 * 400 V connection The machine can be inspected by arrangement.

Condition: good (used), Year of construction: 1989, machine/vehicle number: 4113, functionality: fully functional, operating hours: 4,109 h, overall weight: 6,600 kg, Hydraulic press brake Manufacturer: DoneWell, Hahn & Kolb Stuttgart Type: 80 - 2500 Year of manufacture: 1989 Iodpfezyanljx Aiyebb Control system: Cybelec Model Eva Pac Max. working width: 2500 mm Max. clamping force: 100 t Back gauge: 750 mm with 2 stop fingers Condition: good Die: Multi V 7 angle Tools

Condition: used, Year of construction: 1988, pressure 400 t distance between columns 1100 mm stroke 250 mm no. of strokes 25 - 75 /min distance table/ram, max. stroke up, adjustment up 900 mm table surface area 1100 x 965 mm capacity of ejector in table 30 t ejector stroke of ejector in table 80 mm capacity of ejector in ram 3 t stroke of ejector in ram 60 / 70 mm ram surface 980 x 800 mm column travel -side 800 mm Ibodpfjzrpt Ujx Aiyjb ram adjustment 20 mm power capacity 80,0 + 5,5 kW weight 47,0 t Dimensions (WxDxH) 3,5 x 3,3 x 6,0 m weight of switch cabinet 1,4 t dimensions of electrical cabinet (WxDxH) 4,9 x 0,5 x 2,6 m Multi-station cold extrusion press with link drive with infinitely variable drive, hydraulic clutch-brake combination (Ortlinghaus), hydraulic overload protection in the slide, motorised slide adjustment, pneumatic counterbalance cylinder in press frame, cam-controlled ejector in table (30 t / 80 mm), pneumatic ejector in slide (3 t, 60 mm), motorised central lubrication

Condition: ready for operation (used), Year of construction: 1987, functionality: fully functional, pressing force: 200 t, Hans Schoen NH/LF 200 (UVV) – Powerful & Robust 🔧 Model: Hans Schoen NH/LF 200 📍 Type: Hydraulic Double-Column Press (UVV-certified) 📅 Year of manufacture: approx. 1988 (depending on the specific machine) 📦 Condition: used, fully functional ⸻ 💪 Technical Highlights • Pressing force: approx. 200 t – suitable for demanding forming and drawing applications • Hydraulic drive for precise force and stroke control • Column clearance: approx. 1,050 mm – generous working area • Stroke: approx. 150 mm – efficient travel distance • Table size: approx. 1,000 × 1,200 mm – large clamping area • Table height above floor: approx. 850 mm – ergonomic working height Ibodpfxex Ry Nyj Aiysb • Hydraulic control (often with PLC/Siemens control) possible • Safety and UVV certification for manual loading – increased operational safety 💡 Thanks to its robust construction, this press is ideally suited for series production, drawing and forming processes as well as machining and assembly tasks in metalworking operations. ⸻ 📌 Features & Equipment • Two-hand operation / safety control • Adjustable mechanical stop • Pressure cut-off • Pressure switch • UVV-compliant safety features → all for efficient and safe operation on the shop floor Currently UVV-certified. ⸻ 🛠️ Applications This press offers versatile usage, such as for: • Metal forming / drawing work • Assembly and joining part production • Testing and quality control processes • Series and small batch production ⸻ 📦 Size & Weight • Dimensions (approx.): Width × Depth × Height ≈ 4.0 × 3.6 × 3.4 m • Weight: approx. 16 t – robust industrial construction