Used Manual Bending Machine for sale (72,192)

Condition: good (used), Year of construction: 2008, sheet width 2050 mm plate thickness 20.0 mm ST pre-bending 16.0 mm ST diameter of upper rolls ca. 270 mm side roll diameter ca. 240 mm diameter of lower rolls ca. 250 mm Number of working hours ca. 7.800 h Control "EASY PRO" oil volume ca. 200 Liter voltage 380 V total power requirement 13.5 kW weight ca. 9.000 kg Dimensions (only the machine) 4000 x 2080 x 1800 mm Good condition (!!) Current list price approx. 150.000 euros Special price available upon request Features: - Robust electro-hydraulic 4-roll round bending machine * Arc-shaped feed of the side rollers (swing arm technology) - 4-roller design offers a wide range of bending and rounding options * Rolling process completed in a single pass - Mobile control unit * DAVI "DAVI EASY PRO" numerical control * Manual or automatic operation selectable * Programming "Self-Learning" mode available * Control of all rollers and machine axes * Digital position display for the rollers - Curved feed of the side rollers (DAVI "PSG" guide system) * Tight bending radii of up to 1.1 times the upper roller diameter possible * Instead of the usual 1.5 times with linear guides * Optimal bending = short sheet ends during bending - Conical rolling possible via roller tilt * Tight diameters possible due to low machine frame Bsdpfxszc Rv To Ahkswp - Electronic roller parallelism - Stepless speed adjustment (max. 5.0 m/min) - Bending on both sides - Forged and hardened rollers with a hardness of 53-55 HRC - Low-maintenance, robust machine design - Easy sheet removal thanks to low machine frame - Sturdy welded steel construction - Electro-hydraulic swivel bearing for easy tube removal - Operating instructions

Condition: used, Roll sets for profile bending machine, 3-roller ring bending machine HERKULES WETZLAR Bsdpfsglaq Iox Ahkjwp The rollers are suitable for a HERKULES WETZLAR profile bending machine, type BO 238 N. Shaft diameter: 60 mm with an 18 mm keyway. 2 pieces, roller set No. 1, roller diameter 110 mm, roller width = 180 mm. 2 pieces, roller set No. 2, roller diameter 160 mm, roller width = 40 mm. 3 pieces, roller set No. 3, roller diameter 150 mm, for pipe diameter Ø 33 mm, roller width 87 / 115 mm. - Roller set No. 3 with adapter ring from Ø 93 to Ø 60 mm, without keyway. The machine had 2 driven rollers. Total weight of all rollers: 57 kg. Good condition.

Condition: new, pressure 28 t piston stroke 180 mm diameter of piston 130 mm table-size 300 x 550 mm working feed 2 - 9,8 mm/sek return speed 20 mm/sec Max. pressure 200 bar bending capacity - flat iron 200 x 10 mm weight of the machine ca. 800 kg dimensions ca. 1150 x 1103 x 750 mm The horizontal hydraulic press (28 ton) can be used for many different metal working jobs. The press has a piston stroke of 192 mm and can be equipped with all kinds of tooling for specific bending or straightening jobs. We supply a standard toolingset with this press including a stampholder and backgauge. However, we also produce custom-made tooling for your specific request. Thanks to the NC-control you can easily set the cylinder stroke and save up to 100 working cycles. With this horizontal hydraulic press you are able to bend, straighten, notch, cut and form. A universal hydraulic press that serves all your needs in cold metal working processes. Bwedpfx Ajqzmgqehkep

Condition: as good as new (ex-display), Year of construction: 2023, tool height: 200 mm, bending angle (max.): 180 °, pressing force: 42 t, sheet thickness (max.): 30 mm, sheet thickness copper (max.): 20 mm, lifting speed: 10 mm/s, bending force (max.): 42 t, Stierli bender 420 CNC Horizontal bending machine, with Siemens controler Very universal, for bending flat steel, sheet, round steel, profiles, tubes angular or round, forming tools and easy fixing of own tools or special tools, + straightening as straightening press. Bending pressure 42 tons Tool height 200 mm Stroke 0-300 mm stepless Bodpfx Asgqflqohkowp Bending capacity 200x24 mm S235 Straightening power for HEA180 Bending and straightening program via selector switch Demonstration machine year 2023 incl. hand and foot pedal Horizontalbendingmachine as good as new Please contact us for more information for this horizontal bender.

Condition: like new (used), Year of construction: 2024, tool height: 130 mm, sheet thickness copper (max.): 20 mm, bending force (max.): 12 t, Stierli bender 120 CNC Horizontal bending machine, Siemens controller Working force 12 tons Very universal, for flat steel, sheet, round steel, profiles, tubes angular or round, forming tools and easy fixing of own tools or special tools. tool height 130 mm Bending capacity 130x12 mm S235 Straightening performance light straightening work Pipe bending 3/8"-11/2" Backgauge length stop 1000/2000mm Program memory 200 programs Bending sets 20 bends Demonstration machine year 2024 incl. hand and foot pedal Bwodpfxeflc R Uo Ahksp Machine as good as new

Condition: as good as new (ex-display), Year of construction: 2024, tool height: 300 mm, stroke length: 350 mm, bending angle (max.): 180 °, pressing force: 82 t, sheet thickness steel (max.): 30 mm, sheet thickness copper (max.): 30 mm, lifting speed: 10 mm/s, bending force (max.): 82 t, Stierli bender 820HE Horizontal bending and straightening machine, with manual control and stroke fine adjustment system STRAIGHTENING with this horizontal press: Fast and precise straightening for welding parts, profiles, beams, sheets, pipes, flat steel, etc.... BENDING with this horizontalpress: Very universal, for bending flat steel, sheet, round steel, profiles, tubes angular or round, forming tools and easy fixing of own tools or special tools, + straightening as straightening press. Bsdjgqfmnopfx Ahkswp Bending pressure 82 tons Tool height 300 mm Stroke 0-300 mm stepless Bending capacity 300x20mm (up to 300x30 with large V-block) S235 Straightening power for HEA260 Bending and straightening program via selector switch Demonstration machine year 2024 incl. hand and foot pedal Machine as good as new

Condition: as good as new (ex-display), Year of construction: 2024, turntable diameter: 390 mm, bending angle (max.): 360 °, Stierli Radial 2500 CNC bending machine Radial bending machine with large rotary table for bends up to 360°. Bending power 2500 Nm Bedegqfp Hjpfx Ahkswp Bending capacity flat steel 60x15 mm S235 Bending capacity round steel ø30 mm S2353 turntable ø : 390 or 550mm Pre-feed machine year 2022 incl. hand- and foot pedal Machine as new Works like a classic hand bender, but driven, very precise and programmable. Incl. stop manual or programmable CNC stop 1, 2 or 3m. The bending angles as well as the stop positions are digitally programmable and can be stored in bending programs. The standard tooling is made by simple bending pins. A driver bends the material around these bending pins. These tools can also be manufactured very easily by the customer. In addition to the standard bending bolts, we (or our customers themselves) also manufacture tools for other sections. Possible are sheet metal bending, flat steel, round steel, various profiles, frames etc.. Bending jaws can also be screwed on, which allows bending of very small radii. (similar to a hand bending machine) This machine solves your bending tasks!

Condition: used, total length: 1,330 mm, total width: 1,040 mm, total height: 1,150 mm, Empty weight: 1.800 kg Price: On request - Documentation available: No - CE certificate present: No - Drive system: Conventional - Drive: Hydraulic - Vertical/Horizontal: Horizontal and vertical - Number of rolls [pcs.]: 3 - Number of driven rolls [pcs]: 3 - Shaft diameter [mm]: 75 - Top roll diameter [mm]: 225 - Capacity diameter round [mm]: 60 - Transport dimensions: 1330mm x 1040mm x 1150mm (l x w x h) - Transport weight [kg]: 1800kg Bwjdpfx Aoxuf Slohkop - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, functionality: fully functional, Year of construction: 2011, operating hours: 500 h, control type: PLC-controlled, degree of automation: automatic, actuation type: hydraulic, pipe length (max.): 3,000 mm, tube wall thickness (max.): 2 mm, bending angle (max.): 180 °, overall weight: 300 kg, power: 1.5 kW (2.04 HP), input voltage: 220 V, input current: 12 A, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, Metalworking company sell megabender 030 In the equipment have mandrels for tube: 60,3mm x 2mm R120 50mm x 2mm R75 40mm x 2mm R60 32mm x 2mm R100 Bwjdpfx Ahov Di Dnsksp 700 kg - Powerful mandrel bending machine up to 2 "gas pipe (60.3mm) in semi-automatic design (3000 mm pipe slide length) - Electromechanical drive of the bending axis - hydraulic clamping - mandrel feed / extract - 30 programs x 9 bending angle + correction angle Stainless steel 2mm steel 3mm cooper and aluminium up to 4mm

Condition: good (used), You are bidding on: a high-quality sheet metal shear and bending machine from a very reputable manufacturer – Schechtl. Features of the machine: Sheet metal shear HT 200 Capacity: 1.25mm steel, aluminum, etc. Cutting length: slightly over 2m Holder for round bar (properly attached to the machine; if desired, we also have round bars in various lengths available as an option) Extendable front support Invoice with VAT shown Bedpfx Ahezgua Aokjwp Bending machine KS – Capacity: 1mm steel, aluminum, up to approx. 1.5mm Bending length: slightly over 2m Foot clamp Optional: back gauge or beading device Attachment rail Round rollers and other rails According to §25a UStG The machines are in good used condition and are ready for immediate use. They come from a private owner and a small business (50/50). Important! Optionally, you can find and purchase many machines and machine accessories, such as various rails, back gauges – everything related to sheet metal and steel processing, including bending machines, sheet metal shears, drilling machines, round machining machines, slitting and profiling machines – accessories (beading device, round rollers for gutter production, back stop, etc.), as well as other hand tools and spare parts from many top manufacturers in our shop. Please feel free to contact us if you have any questions. You will receive an invoice according to §25a UStG, which includes the sales tax – differential taxation. Free loading is possible – weight approx. 750 kg and 650 kg. Inspection and testing are possible and welcome after prior telephone arrangement. Payment in cash upon collection. Take advantage of our experience and expertise; we will be happy to advise you. Collection by the buyer (or by a shipping company commissioned by the buyer) should take place within 10 days after the end of the auction. Location: 97249 Eisingen, approx. 3 minutes from the A3 and A81 highways. Article number: Bending machine KS & HT.

Condition: used, LANG PIPE BENDING MACHINE Φ75 Bwodpfx Asw Dbb Dehksp SUITABLE FOR ELBOWS AND SPIRALS COMPLETE WITH FULL SET OF MOULDS IN EXCELLENT CONDITION

Condition: used, Year of construction: 1980, TUBE BENDING MACHINE LANG Bwedpfxorq D N Rj Ahkep TYPE EL90 Φ 90

Condition: refurbished (used), BENDING ROLL MACHINE ROUNDO SHEET METAL LENGHT 2500mm SHEET METAL THICKNESS 30/25mm 3 ROLLS Bjdpfx Ashx N Ukshkowp WEIGHT: 19.000kgr

Condition: refurbished (used), BENDING ROLL MACHINE SHEET METAL LENGHT 4000mm SHEET METAL THICKNESS 15mm 3 BENDING ROLLS PREBENDING Bodpfx Ashxyilshkowp WEIGHT: 23.000kgr THE MACHINE IS IN TOP CONDITION LIKE NEW NEW ELECTRIC PANEL, NEW ELECTRIC CABINET, NEW CABLES, NEW SEALS, MOTOR AND PUMB RESTORATION

Condition: new, Year of construction: 2026, Bending machine ZB 70/3 H NC Zopf - semiautomatic - with foot pedal - with standard roller set TECHNICAL SPECIFICATIONS: - three driven shafts, smooth surface - hydraulic adjusting of the center roller - working position horizontal and vertical - shafts are supported by conical bearings - slide bars on the slide-support are exchangeable - shaft diameter: 40 mm - roller diameter: 152/162 mm - shaft rpm: 8,5 U/min - voltage: 400V 50Hz 3Ph - drivingmotor: 1,1 kW - motor for hydraulic: 1,1 kW - hydraulic pressure: 8 to - adjusting way: 120 mm - weight: 490 kg - dimensions: - colour RAL5012 / RAL7015 NC-CONTROL for ZB 70/3 HA: - two axes controlled Bwsdpfx Aofkz Rbshkjp - touch screen - memorise of 1000 programs ech 19 steps - interpolation - accuracy of the y-axes 1/10 mm - programmable forward and backward

Condition: good (used), Year of construction: 1991, machine/vehicle number: 91212035, Offer 26016 Technical data: - max. working width 2040 mm - max. material thickness at 40 kg/mm² tensile strength 4 mm - bending angle adjustable electronically, preselectable 0 - 135° - automatic sequential control for a complete working process - largest opening width / stroke of the upper beam 350 mm - height adjustment: - of the upper beam 100 mm - of the lower beam 100 mm - upper beam drive 400 V / 4 kW - bending beam drive 400 V / 4 kW - accessories: - motorized bending beam adjustment Bwjdpszgu Tiofx Ahkjp - rear stop adjustable with handwheel - electric foot pedal - space requirement with rear stop: - approx. W 3200 x H 1650 x D 2100 mm - weight approx. 4500 kg

Condition: used, Year of construction: 1988, gebraucht 1988 090151 prompt, Zwischenverkauf v Italien 12800 € 1 42 mm 4665 mm 800 mm 1160 mm 1470 kg 42 x 2,5 mm 40 x 1,2 mm 30 x 40 x 1,7 mm 40 x 30 x 1,3 mm 255 mm 22 mm 180 ° 90 °/s 5.5 kW 120 l Capacity specifications refer to 400 N/mm² Maximum bending radius with pipe guide rollers: 255 mm Maximum bending radius with pipe guide slide: 175 mm Minimum bending angle: 4° Maximum usable length without positioning device: 3900 mm Maximum usable length with positioning device: 3370 mm Bjdpfxoxx A Eks Ahkjwp Adjustable mandrel extension travel from 8 mm Opening and closing travel of the counter-clamping jaws: 0-45 mm Opening and closing travel of the rollers or slides: 12-22-42 mm Operating manual in German Machine does not comply with AMVO or UVV regulations Tools not included BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISE We offer you maximum security and complete transparency. • HONEST INSIGHTS: Detailed photos and functional videos of the current condition • LIVE ON-SITE CHECK: Live testing is possible at our facility • DIGITAL DEMONSTRATION: Individual live demonstration via video call • RISK-FREE PURCHASE: 14-day return policy Details:

Year of construction: 2024, condition: as good as new (ex-display), Stierli bending machine 120HE Bjdpfx Aheid Izgokowp Horizontal bending machine, with bending force of 12 tons tool height 130 mm stroke 0-170 mm bending capacity for flat steel 130x12 mm pipe bending for steel pipes up to 1 1/2" capable of performing minor straightening operations demonstration machine, year of manufacture 2024

Year of construction: 2024, condition: as good as new (ex-display), Stierli bending machine 420HE Horizontal bending machine, with bending force of 42 tons tool height of 200 mm stroke of 0-310 mm, stepless bending capacity of 200x24 mm St40 straightening capacity for HEB180 Bwjdpjid Izkofx Ahksp Bending and straightening program via selector switch Exhibition machine, year of manufacture 2024, incl. hand-held control and foot pedal Wear-resistant machine table Machine in new condition

Year of construction: 2020, condition: as good as new (ex-display), Roll bending machine with spindle feed and 3 driven rollers. Features: Shaft diameter: 40 mm Working position: Horizontal/Vertical with support Connection: 230V/1 phase with inverter Dimensions (W x H x D): 700 x 1460 x 600 mm Weight: 180 kg Performance: Bwedpfx Aogi N Alohkop Round tube: 70 x 1.5 mm Square tube: 50 x 50 x 3 mm Round bar: 35 mm Flat bar: 50 x 10 mm Angle iron: 50 x 50 x 6 mm Scope of delivery: CE40M3D Universal roll set for profiles Accessories (including control panel with foot control, operating manual) 1 set of plastic rollers for round tubes, 1 1/2" for work with reduced marking.

Condition: good (used), Year of construction: 2000, machine/vehicle number: 21977-1964, Offer 26165 Technical Data - Two driven rollers, each hydraulically adjustable - For edging and conical rolling - Operation via a separate control panel, with digital actual value display - and manual operation - Max. working width 1300 mm - Max. sheet thickness at 400 N/mm² without edging - at bending diameter 370 mm, inside 30 mm - with edging at bending diameter 370 mm, inside 25 mm - without edging at bending diameter 380 mm, inside and - width of 370 mm 45 mm - Upper roller diameter each 300 mm - Side roller diameter each 310 mm - Working speed 4.5 m/min - Drive 400 V / 30 kW Bwjdpfxjzf Hkds Ahksp - Space requirement W 5800 x H 1900 x D 2200 mm - Weight 8500 kg

Condition: used, Max. bending length: 2540 mm Max. sheet thickness: 2.5 mm steel Motor-controlled back stop with folding cams up to 1500 mm Several program sequences with different bending angles and stroke heights are possible Control Multibend 2000 Bwjdpfx Aoza Ahpshksp Polished bending rail Weight: 1,700 kg

Condition: new, Year of construction: 2025, Manual bending machine MB-3150 The principal difference that makes our manual bending machine much more functional than other company’s bending machines it’s the removable upper bar. So it lets you the opportunity to replace the slim upper bar to a bar with another configuration (segmented bar or bar for producing of the corrugated sheets). It’s help you to save money for buying additional machines and save the working place. Our manual bending machine has strong rigid construction so it lets you to bend metal sheets without any unwanted deformations. You can purchase manual bending machine MB-3150 mm in a standard set (manual bending machine, roller shear, back table, alidade, angle limiter, side handles). Or you can get additional equipment for the manual bending machine MB-3150 mm: pedals, segmented bar, bar for producing of the corrugated board, absorber, front limiters) There are fourth types of the manual bending machines MB we make: Manual bending machine 1400x1.2mm Manual bending machine 2150x1mm Manual bending machine 2650x0.8mm Bwjdpfxjv T Uvze Ahksp Manual bending machine 3150x0.7mm This manual bending machine bends metal sheets with maximum thickness 0.7mm Our enterprise has started to produce this kind of the manual bending machines since 2003 so we have great experience in doing our job and can propose the great solution to your business. To get information about the price of this bending machine and the way it could be delivered to your location just contact us. We will give you all the information you need. Specifications Maximum material width (mm) 3150 Maximum material thickness (mm) 0.7

Condition: new, Year of construction: 2020, Electric elbow making machine is the mechanism for forming elbow from round and rectangular pipes with different diameters. Elbow making machine EEM-200plus is the better version of EEM-200 machine. It has additional fourth bottom pressing tool so it presses pipes from all four sides while bending and provides better quality of elbow. You can use our machine for working with round pipes as with rectangular pipes. Elbow making machine EEM-200plus lets you to work with pipes from 80 to 200mm. Pay attention: Inside diameter of the pipe you use for bending has to be 1mm bigger than bending matrix of the machine!! The lock of the pipe has to be closed or welded to avoid opening of pipe while bending!! Elbow making machine EEM-200 is electric so it doesn’t need any air or oil system to work. Electric consumption is 1.5 kW/hour for this elbow machine. The needed voltage is 380V. It could be used in environment with temperature from -5 to +45 Celsius degrees. Bjdpfxef Epzns Ahkjwp Elbow making machine is good for bending pipes with maximum thickness 0.8mm. Elbow making machine EEM-200plus bends elbows thank to special pressing tools. There is one set of tools for bending one diameter of pipe you need. So to bend more diameters of pipes you have to get additional pressing tools. It goes four pressing set tools with the machine so you can bend four diameters of pipes with it in the range from 80 to 200mm (that you choose by your own)

Condition: excellent (used), Year of construction: 2016, For sale: Prima Power BCe Smart 2220 (2016) panel bending machine. Main advantages: Bjdpfoxfiw Tjx Ahkowp Servo-electric technology – up to 60% lower energy consumption and up to 70% lower maintenance costs High bending quality and precision Compact layout, operator-friendly design Semi-automatic operation, manual sheet loading/unloading Equipped with a safety system: laser scanners, light curtains Technical specifications: Max. bending length: 2250 mm Max. sheet length: 2850 mm Max. sheet width: 1500 mm Max. panel diagonal: 3000 mm Max. bending height: 204 mm Bending force: 32 t (320 kN) Pressing force: 52 t (510 kN) Processable steel thickness: up to 3.0 mm Minimum thickness: 0.5 mm Average power consumption: 4.0 kWh Additional equipment and features: Software: Master BendCam 2D, Tulus HMI Tool library, visual simulation of the bending process Remote diagnostics, user-friendly control interface Lowerable work surfaces – convenient parts handling Year: 2016 Condition: Used, well-maintained, connected, can be seen in operation. If you have any further questions, we will be happy to answer them.