Used Mechanical Press for sale (17,830)

Condition: new, Year of construction: 2026, Gannomat Concept 70 Eco Laminate – Body press with rapid traverse Technical data: Laminate body press from our showroom; Working area: width from 150 – 2,500 mm, height from 150 – 1,400 mm; depth 700 mm; - Laminate press beam at the top with 6 elements, laminate press beams on the side with 5 elements - Laminate press beams with proven tolerance compensation for tight body joints - Counterpressure surfaces are 40 mm thick, coated, continuous support plates - The pressing force of the press beams is continuously adjusted electronically via 2 potentiometers and set via a frequency converter, therefore, the torque transmission is absolutely wear-free. - Pressing force for horizontal press beams min. 500 daN (kg) to continuously max. 2200 daN (kg) - Pressing force for vertical press beams min. 300 daN (kg) to continuously max. 2200 daN (kg) Gkedpfxjiidm No Ap Doc - Including option: Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams, pressing speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Tapping mode for precise positioning of the two press beams, e.g. for low pressing forces, drawers and bodies at 45 degrees. Simple operation via 6 separate push buttons, freely adjustable preselection of pressing time with automatic opening, loading height 300 mm The machine is in our showroom and can be delivered immediately. Location: in stock at 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, AL-KO POWER UNIT® 300 P-BP 30 -50 Intake nozzle: 300 mm Engine rated power: 7.5 kW / 3-phase Voltage: 400 V / 50 Hz Maximum volumetric flow rate: 6000 m³/h Nominal volumetric flow rate: 5,089 m³/h Negative pressure: 2,587 Pa Filter area: 30 m² Dimensions (L x W x H) in mm: 3,000 x 1,361 x 2,817 Briquetting capacity: 30 - 50 kg/h Briquet diameter: 50 mm Godpfx Ash D If Hep Djkc Weight: 1570 kg Machine is brand new and in stock at our warehouse. - AVAILABLE IMMEDIATELY - Subject to prior sale Location: 54634 Bitburg

Condition: like new (used), Year of construction: 2004, HYDRAULIC PRESS FOR GLUING WOODEN ELEMENTS TO THE THICKNESS OF HSKG Category: VI - Hydraulic presses for gluing wooden parts. The HSKG device is used for gluing wooden cut-thickness parts under high pressure of hydraulic cylinders. The range of achievable crushing forces per cylinder is 5-11kN (horizontal) and 25-55kN (vertical). The gluing of elements is carried out in a stack with the dimensions of the loading field. Stack forming is carried out by hydraulic compression between the sliding vertical beams and the vertical slats of the transverse cylinders. Both stack forming elements are equipped with wooden or metal inserts corresponding to the profile of the slat stack. Gluing wooden elements from the thickness improves the quality of the frames, reduces the cost of machining, reduces the amount of wood waste. Technical and operational data ( of standard execution HSKG - 6m ) Number of loading fields pcs 4 Dimensions of a single loading field - loading height - length of slats in one field mm mm 1140 1530 Maximum width of slats mm 150 Maximum length of glued elements mm 3120 Installed power kW 3 Electricity supply V AC 3/N/PE, 400V 50Hz Control voltage V DC 24 Gjdpfx Aotrl R Asp Dekc Number of actuators on one field: mm mm O 50x100 - 3 pcs. O 80x100 - 3 pcs. External dimensions (L x W x H) mm 8120x1000x2300 Weight of the device kg 4800 At the request of the customer, we also make other configurations of pressure actuators control depending on the expected length of glued elements, as well as other lengths of individual working fields in different quantities in the whole press set, and working width of up to 220 mm maximum with increased pressure force.

Year of construction: 1994, condition: good (used), machine/vehicle number: 24.105, A used, well-maintained hydraulic press brake HATASTAR, equipped with: - CYBELEC DNC 70 control system - Controlled axes Y1, Y2, X, R - Hydraulic upper tool clamping - Hydraulic crowning - FIESSLER AKAS safety system - Tools - Press brake manual - Documentation Bending length 4600 mm Frame width 4100 mm Pressing force 1350 kN Stroke 220 mm Rapid traverse 140 mm/sec Godpfx Apefthzks Dskc Working speed 10 mm/sec Return speed 100 mm/sec Further technical data can be found in the PDF document. Technical data and dimensions: Subject to change.

Year of construction: 2001, condition: excellent (used), Used hydraulic press SACK & KIESSELBACH TRP 200. The originally automatic transfer press was converted to manual in 2012, but can be converted again as an automatic press. The press is still set up and under power and is in very good condition. Pressing capacity in t: 200 Quantity of oil in l: 1100 Stroke in mm: 300 Table size (lxb) in mm: 600 x 600 Daylight in mm: 1000 Upper ejector stroke in mm: 25 Gedpfx Apjhtaaqj Dokc Upper ejector force in t: 10 Total weight in kg: 12000 Operating pressure in bar: 6 Approach speed in mm/sec: 375 Working speed in mm/sec.: 18 - 40

Year of construction: 2019, condition: new, We offer bending tools and punching tools for TRUMPF, AMADA, BYSTRONIC, LVD, SALVAGNINI, DURMA, ERMAKSAN, MVD, and HACO machines. Standard and custom tools. Please send us your requirements, and we will provide you with the appropriate tool. Gksdpfx Apsd H T Tfj Dec

Condition: new, Working width 3000 mm Working height 2000 mm Number of cylinders 5 St. S&S Frame Press, Type T 35 – CE Version ----- Working width: 3000 mm Working height: 2000 mm Manufacturer’s Technical Description: Item 1 00001931 S&S FRAME PRESS, Type T 35 Item 2 00003701 Medium-pressure beam with double-acting pressure cylinder, weight compensation, pressure hose, and shut-off valve, up to 2000 mm high Sturdy welded frame construction made of thick-walled special hollow sections; sliding carriage and pressure beam with 50 mm hole spacing. Continuous abutment on the left side for wide-span compaction; lower abutment in 2 levels. Vertical press cylinders mounted on special pressure beams with one-hand quick adjustment and weight compensation, height-adjustable in 50-mm hole spacing. Long sliding carriages ensure the long-term absorption of high pressing forces. Gkedpfed Ih H Nox Ap Dec Quick, smooth width adjustment via ball-bearing-mounted carriage with central locking, secured in 50-mm hole spacing. Upper horizontal press cylinder is infinitely height-adjustable and equipped with weight compensation. Lower horizontal press cylinder with centering holes for the two abutment levels, without weight compensation. Abutment and pressure plate depth: 100 mm Pressure plate and support width: 130 mm. Electro-hydraulically controlled machine, with 2 vertical pressure cylinders d = 60 mm, stroke 120 mm, double-acting, with weight compensation and one-hand quick adjustment, 2 horizontal pressure cylinders, d = 40 mm, stroke 120 mm, double-acting, with weight compensation; 2 manual control valves, pressure gauge, 1 pressure regulating valve from 20 to 130 bar, corresponding to 550 to 3,500 kg of vertical pressing force. Equipped with a 3 kW three-phase motor for 400 volts, 50 Hz operating voltage. Complete with electrical connection. Painted in RAL 7035 light gray with RAL 7016 anthracite gray. ----- Price of the above machine available upon request! ----- ----- Options: Working widths from 3,000 mm to 5,000 mm Working heights from 2,000 mm to 3,000 mm Optional equipment including a beveling device, counter profiles for single-part production, and much more! Request the complete price list from us! ----- (Technical data according to the manufacturer, subject to change; the illustration may show optional equipment!)

Condition: good (used), Year of construction: 2008, pressing force: 160 t, stroke length: 290 mm, overall weight: 11,000 kg, working width: 4,100 mm, distance between side stands: 3,550 mm, Brand: Dener Model: DMP 160/40 Year: 2008 Bending length: 4,100 mm Force: 160 tons 2 axes (Y, X) *Torsion bar machine, Y axis X stop: 650 mm Cylinder stroke: 290 mm Distance between uprights: 3,550 mm NC control: Dener HT062 Neck: 450 mm Motor power: 15 HP Gkjdpfxjwi Sktj Ap Djc Weight: 11,000 kg

Condition: used, Ražotājs: Munch Modelis: 420 Ražîba: 1 tonna stundā Elektrojauda: 2x75 kW Diametrs 420 mm Komplektā ar dzesētāju pēc kapitālā remonta clear Gsdpfx Aowfqn Asp Djkc 134 / 5,000 Translation results Translation result Manufacturer: Munch Model: 420 Production: 1 ton per hour Electric power: 2x75 kW Diameter 420 mm Complete with cooler after overhaul

Condition: used, Year of construction: 1983, Technical details: pressure: 100 t stroke: 20 fest mm no. of strokes: 55 Hub/min throat: 355 mm Gedeu Nfizjpfx Ap Dekc mortise hole in ram: Ø 36 mm table surface area: 900x640 mm ram adjustment: 150 mm clamping surface ram: 500x415 mm height over floor: 800 mm biggest distance between table & ram: 390 mm passage opening in table: Ø 330 mm total power requirement: 11 kW weight of the machine ca.: 7,5 t dimension machine xH: 1,46x1,58x2,57 m transport dimensions LxWxH: 1,9x1,6x3,1 m Press is without electric cabinet, optional construction of electric cabinet possible. *

Condition: used, Year of construction: 1969, Technical details: pressure: 40 t throat: 220 mm stroke: 10 - 120 mm ram adjustment: 63 mm no. of strokes: 160 Hub/min distance table/ram: 300 mm Table dimensions: LxB: 440 x 620 mm passage opening in table: Ø 200 mm surface area of ram: 400 x 250 mm weight of the machine ca.: 2,52 t dimension machine xH: 1,5 x 1,2 x 1,3 m There is a clamping plate on the table: LxW: 440 x 620 with center hole Ø 100mm. Godju Nfkxopfx Ap Dskc A steel plate 380 x 325 x 27mm is mounted on the ram. The press is equipped with 2-hand control. *

Condition: used, Technical details: pressure: 63 t distance between columns: 900 mm no. of strokes: ca. 75 Hub/min ram adjustment: 80 mm stroke adjustable from - to: 3-100 mm Table dimensions: 900 x 600 mm throat: 310 mm dayligth: max. 350 mm drive power: 11 kW voltage: 380/220/24 V frequency: 50 Hz operating pressure: ca. 150 bar oil volume: 500 l safety distance: 150 mm passage opening in table: 200 mm total power requirement: 11 kW weight of the machine ca.: 4,0 t space requirements of the machine approx.: L:1,8 x B:1,8 x H:3,7 m Gkodou Nfnkepfx Ap Djc DIFFERENTIAL PATH PRESS HIGH SPEED PRESS - High-speed press, C-stand - Compressed air connection: approx. 5 bar Condition. Press is not under power, without switch cabinet, sale as is. - Documentation available i.D. *

Condition: used, Year of construction: 1978, Technical details: Pressure: 160 t max. ram stroke: 500 mm distance table/ram: max. 2880 mm ram speed - forward: 0,03 m/sec ram speed - reverse: 0,04 m/sec ram surface area: B: 1720 x H: 1000 mm ram diameter: Ø 259 mm ram hole: Mitten-Loch: Ø180 mm operating pressure: 260 atü bar total power requirement: 11,0 kW weight of the machine ca.: 18,8 t dimension machine xH: 7,5 x 1,6 x 1,6 m HYDRAULIC HORIZONTAL MULTI-PURPOSE PRESS TÜV test until 02/2024 Details of the counter frame: Godeu Nfq Espfx Ap Dokc Size W: 1720 x H: 690mm Counter support U-support = Ø 225mm x depth = 450mm Manual horizontal displacement: max. length 2880mm Information on the guide cylinder: 2 cylinders opposite each other; size Ø230mm x length 3350mm, 7 cylinders divided by adjustment groove Ø 170x 50mm, can be moved manually with adjustment ring Information on the mounting bed: Steel construction, welded with 2 guide grooves 20mm; size LxWxH: 4000 x 1400 x 200mm *

Condition: used, Technical details: pressure: 200 t stroke: ca. 200mm mm table surface area: L:1200xH:450 mm jaw width: 1000x200 mm total power requirement: 18 kW weight of the machine ca.: 15 t dimension machine xH: 4,5x1,5x2,2 m Beam - Straight Bending Machine - electric box (LxWxH:0,85x0,8x2,7m) Gsdou Nfrpspfx Ap Dskc - chuck intake: LxW 1200x220mm - chuck adjustment 200mm moveable - opening width of chucks 300mm - manual control accessories: - div. limit stops, tools, try square and marking gauges i.D. *

Condition: used, Technical details: pressure: manuell t stroke: 15 mm machine weight approx.: 8,4 kg dimensions of machine: 600x250x70 mm Pneumatic Cable Terminal Press - application: press of cable terminal on electrical cable and air-conditioning lines futher details: - press cylinder: slide Ø 25mm: outer diameter Ø 68mm: maximum extension length approx 15mm - tool fork: width=30mm ; length=70mm - maunal lever Ø 30 x L:300mm equipment Gsdpju Nfr Nofx Ap Dskc - toolbox with div. round and hexagonal tool jaws i.D. *

Condition: used, Year of construction: 1960, Technical details: pressure: 10 t throat: 255 mm max. ram stroke: 400 mm ram speed - reverse: 0,180 m/sec. m/sec. ram speed - forward: 0,080 m/sec. m/sec daylight dimension : table/slide up: 630 mm daylight dimension : table/slide low: 230 mm table clamping surface:: 420 x 400 mm passage opening in table: 220 mm surface area of ram: 200 x 200 x 65 mm total power requirement: 1,6 kW weight of the machine ca.: 1,1 t dimension machine xH: 1,1 x 0,5 x 2,1 m Gedeu Nfudepfx Ap Dskc

Condition: used, Technical details: Pressure: 2,5 t throat: 155 mm max. ram stroke: 280 mm distance table/ram: 450 mm clamping plate on table: 260 x 1000 mm ram speed - forward: 0,08 m/s Gksdju Nfv Ujpfx Ap Djc ram speed - reverse: 0,32 m/s mortise hole in ram: Ø 20 x 45 mm height over floor: 930 mm total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimension machine xH: 0,85 x 1,0 x 17 m The machine is equipped for straightening work. *

Condition: used, Technical details: pressure: 0,9 t daylight dimension : table/slide up: 350 mm throat: 295 mm ram diameter: 40 mm Table dimensions: 600 x 330 mm height over floor: 935 mm weight of the machine ca.: - t dimension machine xH: 1,2 x 0,8 x 2,1 m Punch holder with M24x60mm internal thread Hydraulic power unit Röhm-Gamet, type 1E1 HS299, pressure 38bar, tank capacity approx. 50 liters One-hand operation * Godju Nfw Sopfx Ap Djkc

Condition: new, Year of construction: 2026, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir Gsdpfjw Sgnkex Ap Dskc - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Condition: new, Year of construction: 2026, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, oil tank capacity: 200 l, total length: 3,870 mm, total width: 1,550 mm, total height: 2,400 mm, overall weight: 7,400 kg, feed length X-axis: 600 mm, feed length Y-axis: 120 mm, spindle motor power: 11,000 W, product height (max.): 390 mm, warranty duration: 12 months, Equipment: CE marking, documentation/manual, safety light barrier, HYDRAULIC CNC PRESS BRAKE MTP 125×3200 – 125 T – MTP-3212 – 4 AXES Y1, Y2, X + V The brand-new MTP 125×3200 Hydraulic CNC Press Brake has been designed for precision bending of carbon steel, stainless steel, and aluminum sheets up to 6 mm thick. Thanks to its advanced CNC control system, heavy-duty welded frame, and premium-quality components, the machine is an ideal solution for manufacturing plants, metal fabrication workshops, tool rooms, and engineering companies. The machine is equipped with the MTP-3212 CNC controller and 4 controlled axes (Y1, Y2, X + V), ensuring exceptional accuracy, repeatability, and fast production setup. STANDARD EQUIPMENT • MTP-3212 CNC controller with a large full-color touchscreen • Independently servo-driven Y1 and Y2 axes • Servo-driven X-axis (back gauge) • Automatic crowning compensation (V-axis) • AMADA-type quick tool clamping system • 2 adjustable front support arms • Mobile control panel mounted on a swing arm • LED working area illumination Gksdpfxozg H Ewj Ap Dec The CNC controller automatically calculates bending parameters, features an intuitive user interface, and can store up to 40 tool configurations, significantly reducing setup time. PREMIUM COMPONENTS The press brake is equipped with high-quality components from internationally recognized manufacturers: • Bosch Rexroth hydraulic system • Schneider Electric electrical components • Omron and Schneider Electric safety components • Heavy-duty steel hydraulic tubing for maximum durability and leak prevention ERGONOMICS & SAFETY Designed for maximum operator comfort and safety, the machine is equipped with: • Safety light curtains • Side safety guards • Rear safety fence • Easily accessible emergency stop switches • CE Declaration of Conformity • Operating manual TECHNICAL SPECIFICATIONS • Maximum sheet thickness: up to 6 mm • Pressing force: 125 T • Maximum bending length: 3200 mm • Distance between columns: 2700 mm • Throat depth: 320 mm • Ram stroke: 120 mm • Maximum opening height: 390 mm • Back gauge travel (X-axis): 600 mm • Controlled axes: Y1, Y2, X + V • Main motor power: 11 kW • Power supply: 400 V / 50 Hz • Machine dimensions (L × W × H): 3870 × 1550 × 2400 mm • Machine weight: 7,400 kg TECHNICAL SUPPORT We provide professional technical advice before purchase as well as comprehensive after-sales support. Our specialists assist with tooling selection, bending technology, and machine parameter optimization for different materials. We also offer warranty and after-sales service together with transport arrangements throughout Europe and worldwide. Brand-new machine supplied with the manufacturer's warranty, fully operational and ready for immediate use.

Condition: excellent (used), Year of construction: 2007, operating hours: 1,192 h, functionality: fully functional, machine/vehicle number: 1541, total width: 2,000 mm, total height: 2,500 mm, total length: 25,000 mm, briquette diameter: 90 mm, overall weight: 6,000 kg, Equipment: CE marking, type plate available, Complete production line for cylindrical briquettes, Ø 90 mm. The line includes a Di Più BRIK MB90 briquetting press, an input sawdust conveyor, a briquette cooling tower, a briquette cutter, a briquette sorting conveyor, a shrinking tunnel (packaging machine), and an output roller conveyor. Gsdpfx Apjy U D Uus Dokc

Condition: new, functionality: fully functional, Year of construction: 2026, power: 3 kW (4.08 HP), input voltage: 400 V, input current: 6 A, input frequency: 50 Hz, reverse speed: 14 mm/s, total length: 1,150 mm, total width: 850 mm, total height: 1,800 mm, Special Offer – 5% Discount Available! Hydraulic C-Frame Press – 250 kN (25.5 Tons) The Hydraulic C-Frame Press is a professional industrial machine designed for precise pressing, straightening, bending, assembling and forming operations. Its open C-frame construction provides excellent access to the working area, allowing convenient machining of larger workpieces and easy material handling from multiple sides. The rigid welded steel frame ensures maximum stability, durability and long service life. The precision hydraulic system provides smooth control of both pressing force and ram speed, delivering reliable performance and high machining accuracy. This versatile press is suitable for industrial production, maintenance departments, tool rooms, metalworking workshops and automotive applications. Main Features • Pressing force of 250 kN (approx. 25.5 tons) • Open C-frame design • Heavy-duty welded steel construction • Precise hydraulic control • Smooth ram movement • Excellent access to the working area • Suitable for industrial and workshop applications • CE certified Technical Specifications • Pressing force: 250 kN (approx. 25.5 tons) • Maximum hydraulic pressure: 25 MPa • Maximum opening: 500 mm • Ram stroke: 200 mm • Table dimensions: 500 × 400 mm • Throat depth: 200 mm • Downward speed: 10 mm/s • Return speed: 14 mm/s • Motor power: 3 kW • Packed dimensions (L × W × H): 1150 × 850 × 1800 mm Applications • Pressing • Bending • Straightening • Assembly operations • Metal forming • Metalworking workshops • Automotive industry • Tool rooms • Industrial manufacturing Transport and Delivery The machine is supplied brand new and includes a 12-month warranty, warranty service and professional after-sales support. We provide professional transport throughout Europe using specialized machinery logistics. Every machine is securely loaded, protected during transport and delivered directly to the customer's premises. We also assist with export documentation and international shipping arrangements. Worldwide shipping is available upon request. About Metal Technics Polska Metal Technics Polska is a manufacturer and distributor of professional metalworking machinery. We supply high-quality machines throughout Europe and provide expert technical advice, spare parts and comprehensive after-sales support. Gksdpfxeyr Ek Rs Ap Doc Contact us today for pricing, delivery times, machine availability, additional photos, videos or a personalized quotation.

Condition: used, functionality: fully functional, This offer is for a used ‘Xerox iGen 5 Press’ colour production system Items for sale: 1 x Xerox iGen 5 Press with the following specifications: Includes FreeFlow Print Server Includes 2 x YVC-2 paper decks Includes YVC-3 finisher Includes 5th colour (orange) Not the right configuration? It is no problem to configure the machine to your requirements. Please feel free to contact us! Meter readings: Gjdpfx Ajy Dfcljp Dekc Total: Approx. 15,719,744 pages Condition: This offer is for a used machine, which may show signs of wear (minor scratches or yellowing). The device has been tested for functionality A test printout can be seen in the photo Packaging and shipping: You are welcome to view the device during our business hours. Please arrange an appointment for this! Seaworthy packaging and worldwide shipping available on request! A functional test will be recorded on video for you prior to dispatch or collection. For further information, you are of course welcome to contact us directly.

Condition: used, Year of construction: 2018, controller model: , _____ Description: Year of manuf. : 2018 Control : Technical data Year of manufacture:2018 Pressing force approx.:3200 kN Folding length approx.:4420 mm Control system:TASC 6000 Projection:420 mm Free upright clearance approx.:3680 mm Usable installation height approx.:615 mm Machine weight approx.:23400 kg Gkjdpfsyy Hgqjx Ap Djc Equipment :- Sturdy machine frame :- Press beam, stress relieved with high bending strength :- Spherical bearing of the press beam (inclined position) :- Electro-hydraulic top drive with 4-cylinder technology :- Optical set-up and positioning aid :- Generous edge clearance :- Flat front covers :- Block hydraulics :- Electronic pressure compensator :- Measuring system with glass scale and deflection compensation :- Hydraulic oil in the machine (lifetime lubrication) :- Oil cooler :- Control cabinet cooling via air-to-air heat exchanger :- Modern machine design Extended equipment :- 6-axis backgauge system :- Hydraulic upper tool clamping :- CNC crowning :- Work area lighting front and rear BendMaster (150) :- Sturdy base body and manipulator in cast aluminium construction :- Load capacity 150 kg, plate plus gripper :- Low floor track in welded construction :- Sheet sensor for contour detection :- Rotary feed-through for easy gripper change :- Gripper coupling on BendMaster :- Sensors for 4-axis backgauge system :- Electric drives :- Double sheet detection :- Regripping station NC :- Vacuum generation for suction gripper :- Platform (300 mm) for the bending press Extended BendMaster equipment :Extended BendMaster equipment - Track extension to 12 m :- Sensor system for 6-axis back gauge :- Gripper changing console :- Vacuum gripper, undefined :- Modular vacuum gripper with separation (material for 3 grippers) :- Gripper coupling :- Tong gripper :- Sheet removal station with linear axis :- Side door on right for safety fence

Condition: new, Year of construction: 2026, functionality: fully functional, power: 7.5 kW (10.20 HP), input voltage: 400 V, type of input current: three-phase, pressing force: 125 t, stroke length: 120 mm, table length: 3,200 mm, throat depth: 230 mm, ram plate length: 3,200 mm, distance table to ram: 390 mm, clearance between the columns: 2,700 mm, oil tank capacity: 200 l, total length: 3,870 mm, total width: 1,550 mm, total height: 2,400 mm, overall weight: 7,500 kg, warranty duration: 12 months, Equipment: CE marking, documentation/manual, safety light barrier, AVAILABLE IN STOCK – READY FOR IMMEDIATE DELIVERY HYDRAULIC CNC PRESS BRAKE MTP 125 × 3200 MTP-3212 Touchscreen Control – 125 T – 2 Axes (X, Y) The MTP 125 × 3200 hydraulic CNC press brake is designed for accurate and efficient sheet-metal bending. It delivers 125 tonnes of pressing force and offers a maximum bending length of 3200 mm. The machine can process sheet metal up to 6 mm thick. It is suitable for workshops and manufacturers operating in electromechanical engineering, light industry, agricultural machinery production, shipbuilding, automotive, aerospace, and other metalworking sectors. CONTROL AND EQUIPMENT • X-axis back gauge with servo drive • Y-axis beam adjustment with servo drive • Manual R-axis back-gauge finger height adjustment • Back-gauge travel: 600 mm • Two front material supports • AMADA-style quick punch-clamping system • Control panel mounted on a movable arm • LED working-area lighting MTP-3212 CNC CONTROLLER The MTP-3212 features a large colour touchscreen and an intuitive, user-friendly menu. The software automatically calculates the bending angle, simplifying machine setup and improving production efficiency. The controller can store data for up to 40 punch types. HIGH-QUALITY COMPONENTS The hydraulic system uses high-quality German Rexroth valves. The electrical system incorporates Schneider Electric components, while safety components are supplied by Omron and Schneider. Steel hydraulic connections significantly reduce the risk of future leaks. SAFETY EQUIPMENT • Clearly visible safety markings • Side guards • Rear safety gate • Easily accessible emergency-stop switches • Safety light curtain preventing accidental access between the punch and die The machine is supplied with an operating manual and a CE Declaration of Conformity. TECHNICAL DATA • Maximum sheet thickness: 6 mm • Pressing force: 125 t • Maximum bending length: 3200 mm Gkodpfx Asytp N Hsp Dec • Distance between columns: 2700 mm • Throat depth: 320 mm • Ram stroke: 120 mm • Maximum opening height: 390 mm • Back-gauge travel: 600 mm • Controlled axes: X, Y • Motor power: 7.5 kW • Weight: 7500 kg • Dimensions (L × W × H): 3870 × 1550 × 2400 mm • Front supports: 2 • Controller: MTP-3212 • Punch clamping: AMADA-style quick clamping TECHNICAL SUPPORT Our specialists can assist with planning bending sequences for complex parts, selecting suitable materials and tools, and choosing optimal working parameters. Pre-purchase technical consultation is also available to help select the correct machine and accessories. Delivery can be arranged. Transport costs are calculated individually according to the destination. Please provide the delivery address or postal code to receive a quotation.