Used Okuma Lu 300 for sale (222)

Condition: good (used), spindle bore: 360 mm, travel distance X-axis: 798 mm, travel distance Z-axis: 358 mm, spindle motor power: 45,000 W, rotational speed (max.): 500 rpm, total height: 2,100 mm, total length: 8,100 mm, total width: 2,750 mm, overall weight: 13,000 kg, Chip conveyor  SMW Front and Rear chuck 700 mm  Double revolver 6+8 positions Big Bore 360 mm Tailstock with power quill Tooling package included with inserts and jaws Max. turning Ø:665mm X-Axis: 798mm Bjdpfxjwxb Ere Amnoli Z-Axis: 358mm Spindle bore: 360mm Speedrange: 500Rpm Spindle power: 45kW Pinole taper: 6Mk Stroke pinole: 230mm Quill Ø: 150mm Length: 8100mm Width: 275mm Height: 2100mm Weight: 13000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2014, turning length: 700 mm, travel distance X-axis: 205 mm, travel distance Z-axis: 700 mm, spindle motor power: 22,000 W, total height: 2,800 mm, total length: 6,000 mm, total width: 3,900 mm, overall weight: 9,800 kg, Complete machining with twin spindel, upper and lower turrets Kitagawa 3 chuck left and right Tool holders with driven tools axial and radial Large jaws cabinet with inserts OGL Gantry loader with ca 10 Kg load capacity Chip conveyor Paper Filtration Pressure Tank Max. turning Ø: 400mm X-Axis: 205mm Z-Axis: 700mm Bedpfxjyn Em Ro Amnsli Spindle bore: 62mm Speedrange: 6000Rpm Spindle power: 22kW Subspindle speeds: 6000Rpm Subspindle bore: 62mm Subspindle power: 15kW ATC / revolver: 16 Speed live tools: 6000Rpm Positions lower revolver:16 Speed live tools: 6000Rpm Power live tools: 7kW Chip conveyor: yes Tool eye: yes Length: 6000mm Width: 3900mm Height: 2800mm Weight: 9800kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), Year of construction: 2006, operating hours: 19,067 h, functionality: fully functional, machine/vehicle number: 122616, travel distance X-axis: 500 mm, travel distance Y-axis: 95 mm, travel distance Z-axis: 1,650 mm, controller model: OKUMA OSP P200L, center width: 1,500 mm, TECHNICAL DETAILS Travel in X-axis: 500 mm Travel in Y-axis: 95 mm Travel in Z-axis: 1,650 mm Swing over bed: 550 mm Power: 22.0 kW Distance between centers: 1,500 mm Spindle bore: 80 mm Counter spindle speed: 4,500 rpm Tool magazine: 44 tools Tool holder: HSK-F63 Spindle speed: 12,000 rpm MACHINE DETAILS Control system: OKUMA OSP P200L Bedpsy Rxprofx Amnjli Dimensions & Weight Dimensions (L x W x H): 5,100 x 2,800 x 2,900 mm Shipping weight: 13,700 kg Shipping packages: 7 pieces Operating hours: 19,067 h EQUIPMENT Automatic workpiece loader with controlled arm from Pneumotec Automatic bar feeder from LNS Quick Load Servo III Counter spindle VAC-MB11 Milling head with automatic tool changer Turret: 12 tool positions Chip conveyor Turret head Powered tools Bar loader 3-jaw chuck Tool magazine C-axis Documentation CE marking

Condition: used, Year of construction: 2022, machine/vehicle number: L2E0253, CNC lathe Bjdoy Axr Repfx Amnjli

Condition: used, Year of construction: 2019, machine/vehicle number: 0711-101349, Equipment: chip conveyor, CNC vertical machining center Bjdpfx Amsy Axf Donjli

Condition: used, Year of construction: 2014, Technical details: x-travel: 760 mm y-travel: 760 mm z-travel: 760 mm total power requirement: 43 kW weight of the machine ca.: 11,5 t dimensions of the machine ca.: 2,7 x 4,73 x 2,87 m Bsdjxrwpdspfx Amnjli max. table loading capacity: 500 kg

Condition: used, Year of construction: 1980, Machining center Bsdpfsyycv Isx Amneli

Condition: ready for operation (used), Year of construction: 2013, travel distance X-axis: 1,500 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 660 mm, controller manufacturer: OKUMA, controller model: OSP-P300M, table load: 1,500 kg, overall weight: 9,000 kg, spindle speed (max.): 15,000 rpm, spindle motor power: 30,000 W, number of slots in tool magazine: 32, number of axes: 3, This 3-axis Okuma MB-66VA was manufactured in 2013. It features an X-axis travel of 1500 mm, Y-axis travel of 660 mm, and Z-axis travel of 660 mm. The machine is equipped with a powerful 30 kW spindle, capable of reaching speeds up to 15,000 rpm, and has a tool magazine with 32 positions. If you are looking to get high-quality machining capabilities, consider the Okuma MB-66VA vertical machining centre we have for sale. Contact us for further details. Bedsy Ndp Ispfx Amnjli • Table size: 1500 × 660 mm Technical Specification Taper Size BT 50

Condition: ready for operation (used), Year of construction: 2016, operating hours: 23,563 h, travel distance X-axis: 1,050 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 460 mm, controller manufacturer: OKUMA, controller model: OSP-P300M, table load: 900 kg, overall weight: 7,000 kg, spindle speed (max.): 15,000 rpm, spindle motor power: 22,000 W, number of slots in tool magazine: 32, number of axes: 3, This 3-axis Okuma M560-V was manufactured in 2016. It features a generous X-axis travel of 1050 mm, Y-axis travel of 560 mm, and Z-axis travel of 460 mm. The machine is equipped with a powerful 22 kW spindle and a tool magazine that holds 32 tools. If you are looking to get high-quality machining capabilities, consider the Okuma M560-V vertical machining centre we have for sale. Contact us for further details. Bljdpfx Amjy Nb T Denoi • Table size: 1300 × 560 mm

Condition: ready for operation (used), Year of construction: 2013, travel distance X-axis: 762 mm, travel distance Y-axis: 460 mm, travel distance Z-axis: 460 mm, controller manufacturer: OKUMA, controller model: OSP-P200M, table load: 800 kg, overall weight: 6,000 kg, spindle speed (max.): 15,000 rpm, spindle motor power: 15,000 W, number of slots in tool magazine: 20, number of axes: 3, This 3-axis Okuma M460R-VE vertical machining centre was manufactured in 2013. It features a robust X-axis travel of 762 mm, Y-axis travel of 460 mm, and Z-axis travel of 460 mm. The machine is equipped with a powerful 15 kW spindle that can reach speeds of up to 15,000 rpm, along with a tool magazine capacity of 20. If you are looking to get high-quality machining capabilities, consider the Okuma M460R-VE machine we have for sale. Contact us for further details. • Table size: 1000 × 460 mm Blodoy Nb Nxjpfx Amnsi Technical Specification Taper Size BT 40

Condition: used, Year of construction: 2012, functionality: fully functional, 1 OKUMA CNC Lathe Model LT2000EX-2M1Y with OSPP200LA CNC Controller Including CE mark 1 set 〈European Standard Specification〉 1-1 Spindle motor VAC 11/7.5 kw (5 min./cont. ) 2 set 1-2 Spindle speed 50 - 6,000 min-1 2 set 1-3 Spindle dia. 62/100 mm, 140 Flat nose 2 set 1-4 C-axis control, 360 degree at 0.001 degree increment 2 set 1-5 Y-axis 95mm (+50 to -45) for upper turret 1 set 1-6 Upper V16 (turning & milling) + Lower V16 (turning & milling) Radial turret (No tool holder included) 1 set 1-7 Rotary tool drive motor, PREX 5.5/3.7kw (2 min/count) 2 set 1-8 Rotary spindle speed 45-6,000 min-1 2 set 1-9 Coolant supply system, 0.8kw x 3 sets pump motor 1 set 1-10 Work light, fluorescent lamp 1 set 1-11 Totally enclosed guard 1 set 1-12 Door interlock 1 set 1-13 Chip pan, side chip disposal type 1 set 1-14 Foundation washers and leveling jack screws 1 set 1-15 Machine lifting hooks 1 set 1-16 Chuck auto open / close with confirmation 2 set Bljdpfxjy Rnbdj Amnoi 1-17 Chuck air blower 2 set 1-18 Lubrication monitor B-1 1 set 1-19 CE mark and EMC 1 set 1-20 Application for IEC standard 1 set 1-21 Double chuck operation pedal 2 set 1-22 Synchronized tapping (for LT2000EX-M) for Milling rotary tool 1 set 1-23 OSP-P200LA CNC Controller with 15" colour display, touch panel 1 set 1-24 OSP-P200LA 3D-M-E kit specifications 1 set *Multitasking machines Coordinate conversion (1 set) *Multitasking machines Profile generation (1 set) *Program storage Standard: 2GB (1 set) *Operation buffer Standard: 2MB (1 set) *Real 3D simulation (1 set) *Cycle time over check (1 set) *Load monitor (spindle, feed axis) (1 set) *NC operation monitor (incl. counter and monitoring function) (1 set) *Cycle time reduction function (1 set) *Variable spindle speed control (1 set) 1-25 Pitch error compensation X + Ys + Z 1 set 1-26 Inch / metric switchable function 1 set 1-27 Workpiece jump out detection 1 set 1-28 Status indicator lamp (2-layer lamp) instead of status indicator in 3D-E kit 1 set 1-29 Electrical power source application to suite local power source at each countries (CE transformer) 1 set 1-30 Chuck open/close during spindle rotation (LT-Standard) 1 set 1-set of tools - see last photo

Year of construction: 1988, condition: ready for operation (used), Interface: RS232C, connected load: 21kVA, control system: Okuma OSP 5000 L-G, length: 2900mm, width: 1800mm, height: 1720mm, weight: 4.5t, ball screw of the X-axis has 0.2mm backlash, regularly maintained, with chip conveyor. An on-site inspection is possible. Bjdey U Nq Uepfx Amnsli

Year of construction: 2006, operating hours: 19,067 h, condition: used, total length: 5,100 mm, total width: 2,800 mm, total height: 2,900 mm, Colour: Grey Empty weight: 13.700 kg Price: On request Turning and milling center Total: 9-axes, B-Axis, Y-Axis, C-Axis Automatic product feed with controlled arm from Pneumotec Automatic bar feeder from LNS Quick Load Servo III Sub-spindle VAC-MB11 4500 rpm Milling head with automatic tool changer and 44 ATC units Lathe turret: 12 ATC units Chip conveyor - Year: 2006 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 122616 - Operating hours: 19067 - Drive system: CNC - Control system brand: OKUMA-OSP - Control system type: OSP P200L - Power [kW]: 22.0 - Swing over bed [mm]: 550 - Distance between centres [mm]: 1500 - Spindle bore [mm]: 80 - Options: Turret, Live tools, Bar feeder, Three-jaw chuck, Tool magazine, Chip conveyor, C-axis - └ Tool magazine [pcs.]: 44 - X-axis travel [mm]: 500 - Y-axis travel [mm]: 95 - Z-axis travel [mm]: 1650 - Tool holder: HSK-F63 - Type of bar feeder: LNS Quick Load Servo III - Transport dimensions: 5100mm x 2800mm x 2900mm (l x w x h) - Transport weight [kg]: 13700kg - Transport packages [pcs.]: 7 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Bjdpfx Asy N Dt Hjmnjli Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2004, power: 37 kW (50.31 HP), travel distance X-axis: 1,000 mm, travel distance Y-axis: 950 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: Okuma, total height: 3,280 mm, total length: 6,500 mm, total width: 3,460 mm, table width: 630 mm, controller model: OSP-E100M, spindle speed (min.): 12,000 rpm, table height: 630 mm, Okuma MA-600 HB Space Center OSP E 100M control Dimensions pallet 630 x 630 mm Number of pallets 2x X-axis travel 1000 mm Y-axis travel: 950 mm Z-axis travel 1000 mm Indexing of table 1° Spindle holder MAS BT 50 Spindle speed 12,000 rpm Spindle motor 37/26 kW Bjdpfxsy N Afus Amnoli Positions in the tool magazine 60 If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: excellent (used), Year of construction: 2002, OKUMA Euro Center V50 Year of construction 2002 Control system OSP-U100L Travel distances X-1020 Y-510 Z-525 Table load 680kg Clamping surface 1200x510 Bedpfxerfw Nhj Amnsli Tool changer 20 magazine places chip conveyor

Condition: good (used), Year of construction: 2005, functionality: fully functional, The machine was serviced annually under a maintenance contract with Okuma. Okuma Mac Turn 550 W / 9-axis turning-milling center Year of manufacture: 2005, Control system: OSP-E 100 L / Expansion Kit “M” Kit One Touch IGF Milling spindle carriage X/Y/Z/B, Counter spindle W-axis, Main spindle with C-axis, Counter spindle with C-axis, Turret carriage below X/Z axis, Max. turning diameter: 720 mm, Turning length: 2,000 mm, Distance between tailstock center and spindle center: 2,505 mm, Y-axis: 250 mm / +/- 125 mm, Main spindle speed: up to 3,500 rpm, Spindle power: 30 kW Turret below: 12-station without driven tool stations, Nco Dmnbyeyt Nvtoujt Turret below with steady rest, therefore only 9 stations instead of 12, Self-centering steady rest: 35 - 240 mm, Milling spindle: infinitely variable B-axis 0.001°, Magazine: 80-station, Mount: HSK 100, New Forkhart three-jaw chuck Ø 400 mm, value 12,000 €, Counter spindle without chuck, currently with arbors / delivery without arbors, Enlarged main spindle: 110 mm Ø 150/110 mm, Spindle nose: Size 11, 2-stage clamping pressure, Counter spindle as a hollow shaft motor, speed up to 3,800 rpm, Ethernet LAN interface, Renishaw in-process measurement, Additional measuring system for Y-axis, Tool length: 450 mm instead of 350 mm, Door automation for both doors, Chip conveyor, Gravity belt filter with clean tank 900 liters, Supply pump, frequency-controlled up to 20 bar, The machine was serviced annually under a maintenance contract with Okuma. In 2023, the cable carrier for the W-axis, including all hoses, was replaced. In October 2024, the linear guides X/Y/Z were replaced. Work performed by Okuma. Machine cleaned. Sheets and covers removed. 8th axis removed. Travel stand removed and lifted out of the machine. ATC removed and lifted out of the machine. Bledsy Uhfkopfx Amnei All linear guides removed. Mounting surfaces of the Z-axis cleaned. New linear guide for Z-axis including shoes installed and tightened with the specified torques. New ball screw for Z-axis including bearing mounted and installed. Base plate of the travel stand installed and tightened with the specified torques or screwed onto the shoes. Lubrication lines connected. ATC including attachments installed and connected. New linear guides YA and XA installed and tightened with the corresponding torques. New ball screw YA including bearing installed. Travel stand installed and lubrication lines connected. Base plate XA placed and aligned. 8th axis placed and aligned. H1 turret installed - Install drive motor for the 8th axis - Assembly of 8th axis + new H1 and adjust geometry - Functional test of 8th axis and H1 - Run-in program for B-axis approx. 12 hours, then drain old oil from the 8th axis - Run-in program for H1 and create defect report for OEG - Install left door, adjust various sheets - Install chuck - Adjust zero points - Check tool change

Condition: good (used), Year of construction: 2004, functionality: fully functional, CNC turning and milling center with 9 CNC axes, Okuma MacTurn 350 W, Year of manufacture 2004, OSP-E 100L, Additional magazine, Magazine with 80 tool positions, Main spindle with C axis, Counter spindle with C axis, Y-axis slide above / milling spindle, HSK 63 tool holder, Infinitely adjustable B-axis as milling spindle, Distance between centers 1500 mm, Spindle bore 80 mm, Max. turning diameter 550 mm, Turning diameter 350 mm, Lower turret with 12 tool positions and powered tools, Interlite compact filter system 900 l, Extraction system, Spindle running time approximately 18,300 hours, Chip conveyor, Tool changer gripper arm completely renewed, High-pressure cooling, Bedey Uhccopfx Amnoli WZG measuring arm, Tool changer overhauled, Main spindle Kitagawa B - 210, Counter spindle Kitagawa B - 208.

Condition: good (used), Year of construction: 2002, Ref. -No.: 10434 Manufacturer: OKUMA Type: LC 40 Year of construction: 2002 Type of control: CNC Control: FANUC 18-i TB Storage location: Halberstadt Country of origin: Germany Turning Speeds: 10 - 2.800 RPM Bar passage: 91 mm Chuck diameter: 450 mm Tailstock - diameter: 120 mm Turning Diameter: 550 mm Turning Length: 800 mm Swing Diameter: 800 mm Spindle passage: 90 mm Spindle nose: A2-8 Tailstock Quill Stroke: 150 mm Total Power Requirement: 44 kW Weight Of The Machine Ca.: 8 t Number of tool stations: 12 pc Bljdpfoy Ed Ayjx Amnei

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, travel distance X-axis: 560 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 625 mm, Machine type: Horizontal machining center Manufacturer: OKUMA Type: MA-400HA Year of manufacture: 2008 Control system: OSP P200M Country of origin: Japan Delivery time: short-term, by arrangement 4-axis machining center, high productivity, including various accessories Machine equipment: - ConSep chip conveyor system with high-pressure pump - Various software packages - Touchsetter with length measurement and breakage detection - Work area shower Technical details: - Travels - Axes X-axis (column right-left) mm 560 Z-axis (table forward-backward) mm 625 Y-axis (spindle up-down) mm 610 B-axis 1° 0 - 360° - Number of pallets: 2 (pallet changer for 2 pallets) - Pallet size (mm): 400 x 400 - Max. pallet load capacity (kg): 400 - Max. pallet workpiece dimensions (mm): 500/600 x 710 - Spindle speed (rpm): 15,000 - Main spindle (10min/cont): 22/18.5 kW - Tool holder: BT40 - Tool magazine: 60 positions Optional: Bledpfjy Tvrvox Amnei - Transport organization and execution - Machine delivery and installation - Machine commissioning

Condition: ready for operation (used), Year of construction: 2013, This Okuma MCR-A5C30x65 gantry milling machine was manufactured in 2013. It features a robust 100 mm spindle, capable of speeds up to 4000 min⁻¹, and accommodates a maximum workpiece size of 2540 mm by 5540 mm. The machine supports a hefty 30,000 kg on its 2500 × 6300 mm table. Ideal for heavy-duty milling with a rapid feed rate of 20,000 mm/min. Contact us for more information about this machine. Machine Benefits Technical Machine Benefits Bledpfx Aex D S Ekjmnsi • Dimensions of machine (lxwxh): 2500 mm x 6600 mm x 6350 mm / weight (kg): 59000 kg • Max workpiece width: 2540 mm / max workpiece length: 5540 mm • Table size (width × length): 2500 mm × 6300 mm /max load on table: 30000 kg table height from floor: 850 mm /effective width between columns: 3050 mm/ t-slot (width × number): 24h7 × 13 • Cutting feed rate: 1 to 10000 mm/min/ rapid feed rate: 20000 mm/min/ table movement x-axis: 6500 mm /x-axis travel: 6500 mm /y-axis travel: 3500 mm/ z-axis travel: 650 mm • Tool holder: bt50 + masz type/ tool storage capacity: 50 tools /max tool length: 300 mm • Power supply: 400v, 3 /phases, 50hz rated capacity: 513 kva /full load current: 741 a /peak current: 117/138 a /short circuit current: 18 ka • Spindle diameter: 100 mm /spindle speed: 30 to 4000 min⁻¹ • Large table size suitable for heavy loads. /extensive tool storage capacity. /high rapid feed rate for efficient operations.

Condition: used, Year of construction: 2000, max. 800 mm turning length max. 800 mm chuck ohne documentation inkl. control Okuma OSP turning speed range 10-2800 U/min bar material dia. ca. 91 mm spindle nose A2-8 output 44 kw chucking diameter ca. 450 mm 12 Fach tail stock ca 150 mm Bjdpfx Aoh D Anasmnoli weight of the machine ca. 8 t +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: ready for operation (used), Year of construction: 2002, operating hours: 20,204 h, functionality: fully functional, turning length: 1,025 mm, turning diameter: 530 mm, travel distance X-axis: 475 mm, travel distance Z-axis: 1,170 mm, quill stroke: 150 mm, controller model: Okuma OSP-E100L, TECHNICAL DETAILS Distance between centers: 1,000 mm Swing over bed: 550 mm Maximum machining diameter: 530 mm Maximum workpiece length: 1,025 mm Travels Bledpjxvzp Asfx Amnoi X-axis: 475 mm Y-axis: ±80 mm Z-axis: 1,170 mm C-axis: 360° (continuous) B-axis indexing angle: 1° Main spindle Spindle speed: 5,000 rpm Spindle nose: JIS A2-6 Taper bore diameter: 62 mm Bearing diameter: 100 mm Sub spindle Spindle speed: 6,000 rpm Spindle nose diameter: 140 mm Taper bore diameter: 43 mm Bearing diameter: 80 mm Milling spindle Speed range: 6,000 rpm Feed rates Rapid traverse X-axis: 30 m/min Rapid traverse Y-axis: 26 m/min Rapid traverse Z-axis: 40 m/min Automatic Tool Changer (ATC) Number of tools: 84 Maximum tool length: 250 mm Maximum tool diameter: Ø120 mm (with adjacent stations empty) Maximum tool weight: 5 kg MACHINE DETAILS Control: Okuma OSP-U100L Dimensions (L x W x H): 3,820 × 2,645 × 2,900 mm Weight (without tool magazine): 12,500 kg Main switch-on hours: 20,204 h EQUIPMENT Automatic tool change system High-speed M-spindle with coolant supply 360° C-axis for continuous machining Robust B-axis with 1° indexing Precision sub spindle for second machining side Stable turret with ATC system

Condition: ready for operation (used), Year of construction: 2010, spindle speed (max.): 4,500 rpm, travel distance X-axis: 165 mm, travel distance Z-axis: 400 mm, spindle motor power: 11,000 W, total height: 1,569 mm, overall weight: 3,800 kg, controller manufacturer: OKUMA, controller model: OSP P200 L, number of axes: 3, This 3-axis Okuma GENOS L200E-M was manufactured in 2010. It features a maximum turning diameter of 200 mm and a turning length of 380 mm. The machine is equipped with a spindle speed of 4,500 rpm and a main spindle power of 11 kW. If you are looking to get high-quality turning capabilities, consider the Okuma GENOS L200E-M horizontal turning machine we have for sale. Contact us for further details. • Max swing over covers: 450 mm • Max turning diameter: 200 mm • Max turning length: 380 mm • Spindle nose: ASA A2-6 • Front bearing diameter: 100 mm • Spindle bore: 62 mm • Bar capacity: 50 mm • Rapid traverse (X/Z): 20–25 m/min • Tailstock taper: MT No. 5 • Tailstock quill stroke: 100 mm • Turret type: VDI-30 V12 • Indexing time (1 position): 0.1 sec • OD tool size: 20 x 20 mm • ID tool size: 32 mm • Live tool speed: 6,000 rpm Bsdey A I Stjpfx Amnjli • Live tool power: 4.0 / 1.8 kW • Floor space: 2.081 x 1.550 m • Total power on time: 23,498 hours • Operating time: 6,490 hours • Cutting time: 5,278 hours Additional equipment • Static tool holder kit included Technical Specification Counter Spindle No Driven Tools No

Condition: new, Year of construction: 2018, functionality: fully functional, Standard technical data: Swing diameter over bed: 580 mm Swing diameter over carriage: 470 mm Maximum machinable diameter: 360 mm Max. workpiece length: 250 mm Traverse (X): 260 mm Blsdpfjy H H Afox Amnsi Traverse (Z): 350 mm Traverse (Y): 100 mm (+/- 50) C axis: 360 degrees (0.001-degree increments) Spindle speed: 50-6,000 rpm Spindle nose: JIS A2-6 Spindle bore diameter: Ø62 mm Front spindle bearing diameter: Ø100 mm Turret type: M-V12 Number of tools: 12 Tool size: 20x20 mm Tool shank diameter: Ø32 mm Tool change time: 0.1 sec Driven tool speed: 45-6,000 rpm Rapid traverse (X): 25 m/min Rapid traverse (Z): 30 m/min Rapid traverse (Y): 12.5 m/min Main motor power (15 min/continuous): 11/7.5 kW (PREX) Driven tool motor power: 5.5/3.7 kW (PREX) Machine dimensions (L x W x H): 2,020 x 1,734 x 2,250 mm Machine weight: 4,050 kg Control: OSP P300L Standard specification: 1 OKUMA CNC Lathe Model LB2000 EXII MYC with OSP-P300L CNC Controller, including CE mark & EMC 1 set European Standard Specification 1-1. V12 radial turret head, 1 set 1-2. Spindle, 1 set (1) Spindle speed: 50-6,000 rpm (1 set) (2) Spindle motor PREX 11/7.5 kW (1 set) (3) Spindle: JIS A2-6; bore Ø62 mm (1 set) (4) C-axis control, 360 degrees (0.001-degree increments) (1 set) (5) SR1146 hydraulic cylinder for chuck (1 set) 1-3. MT4 tailstock 1-4. Dual-action foot pedal for chuck and tailstock side, 2 sets 1-5. Driven tool motor PREX 5.5/3.5 kW (2 min continuous) 1 set 1-6. Driven tool speed: 45 - 6,000 rpm, 1 set 1-7. Work area lighting, 1 set 1-8. Full enclosure, 1 set 1-9. Chip tray, 1 set 1-10. Door interlock, 1 set 1-11. Lubrication monitoring, 1 set 1-12. Automatic chuck open/close on main spindle, 1 set 1-13. Chip air blow, 1 set 1-14. Foundation bolts, 1 set 1-15. Tool setter, 1 set 1-16. CE marking, 1 set 1-17. IEC standard compliance, 1 set 1-18. Transformer, 1 set 1-19. Coolant system with 250W pump, 1 set 1-20. OSP-P300L CNC control with 15" color touchscreen monitor, 1 set 1-21. OSP-P300L Advanced One Touch IGF-M-E kit specification (1 set) * Multitasking machines coordinate conversion (1 set) * Multitasking machines profile generation (1 set) * Advanced One Touch IGF (graphical programming assistant with dialogue-based interface) (1 set) * Real 3D simulation (1 set) * Cycle time monitoring (1 set) * Load monitor (1 set) * NC operation monitor (1 set) * Cycle time reduction function (1 set) * Hi-Cut Pro (machining-specific servo optimization) (1 set) * Variable spindle speed control (1 set) 1-22. 2-stage position indicator lamp, 1 set 1-23. Program storage: 2GB, 1 set 1-24. Operation memory: 2MB, 1 set 1-25. Spindle orientation, electric, 1 set 1-26. Inch/metric conversion, 1 set 1-27. Ball screw pitch error compensation on X/Z axes, 1 set 1-28. Workpiece ejection monitoring, 1 set 1-29. Lifting hooks, 1 set 1-33. TAS-C thermal compensation on the frame 6” chuck Chip conveyor

Condition: used, Year of construction: 1994, functionality: fully functional, machine/vehicle number: 0607.1447, turning diameter over cross slide: 340 mm, turning length: 520 mm, turning diameter: 530 mm, spindle bore: 62 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 45 rpm, travel distance Y-axis: 260 mm, travel distance Z-axis: 520 mm, spindle motor power: 15,000 W, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 20 m/min, total height: 1,750 mm, total length: 3,000 mm, total width: 1,700 mm, type of input current: three-phase, overall weight: 5,000 kg, Equipment: documentation/manual, Control: OKUMA OSP5020L 12 tools Automatic chip conveyor Bsdsy Stxqspfx Amnoli