Used Universal Washer for sale (4,958)

Condition: excellent (used), Year of construction: 2014, operating hours: 11,440 h, DMG 5 axis Simultaneous HSC 30 Linear Year 2014 Heidenhian TNC640 Control Travel X320 / Y 300 / Z280mm B axis +/- 120 degree C axis 360 x 0.001 degree HSK-E40, 40,000rpm Swivel rotary table Touch Probe BLUM Tool Measuring system 3D Quick Set Application Tuning Cycle Air Blast through spindle Super Fine filter system c/w tooling ----- Clearance Sales ----- Lhedpsw Hxiwefx Aanjr

Condition: used, New: Yes Field of application: Mining Power: 110 kW (150 HP) Empty weight: 35.000 kg Dimensions (LxBxH): 700 x 240 x 240 cm Engine type: V-type Volume of the tank: 20 m^3 Productivity: 400 tph Log(Blade) Washer(With SKF AUTOMATIC LUBRICATION) Model : LW25 Machine Size : 2000 X 7000 X 2 (Double row) Drive System : 2 X 55 kW Feeding Size : 0 - 50mm Main Body : It is Manufactured ST37 A1 Quality 8mm Sheet as Twisted er Sheet to Which the Front Reducer Group is Connected Will be Manufactured From 12 mm Sheet Metal. Helice: Double Row Carrier Spiral Spoons ST 37 are Manufactured From 8 mm Sheet and the Arms Against Wear Will be Covered With Casting, Helices Will be Hardox Coated. Shaft : Made of Cr-Ni-Mo Alloy Steel. Housing : GS52 Steel Casting Parts Used. Bearing : SKF or FAG Mark Heavy Duty Spherical Roller Bearings. Ljdpfxjx D Dage Aanshr

Condition: new, Year of construction: 2026, FABO Bucket wheel washers are intended to maximize the support of various terms throughout the process, such as the maximum recovery of fines or maximum remove of fines with lower power capacity. Sand and water compound is supplied into the washing tank of bucket wheels and the sand is obtained and dewatered by impellers after washing. The dirty water enters the spiral tank for fine sand pressing, then the pressed fine sand is shifted into the bucket wheel tank by the gradually rotating spiral blade, the fine sand is carried out by the buckets, dewatered and discharged. Lhedpfx Aswbql Hoansr

Condition: ready for operation (used), Year of construction: 2019, General Data Measurements width 2387 mm Measurements depth 3978 mm Measurements height 2565 mm Machine weight 8200 kg Control Unit Brand HAAS Main Drive Spindle speed range 12000 Tool taper ISO 40 Number of axis 5 Movement X-Axis Movement 762 mm Y-Axis Movement 508 mm Z-Axis Movement 508 mm Table Table load 300 kg Lhodpfx Aaex I S Ntonor This 5-axis HAAS UMC-750 was manufactured in 2019, featuring a robust universal machining center with a 500 mm table diameter and a maximum table load of 300 kg. It includes a high-speed spindle up to 12,000 rpm, ISO 40 taper, and a 40-position tool changer. Ideal for complex geometries and diverse machining tasks. Contact us for more information about this machine. Application Types Milling

Condition: excellent (used), For sale: the Austrian-made Voest DA160 lathe shown in the photos. The machine is in very good condition, as indicated by the quiet spindle operation and the absence of play in the mechanisms. The machine was purchased from a training workshop. Overall condition is rated as very good. Loading of the machine is provided. Price is net. Spindle speed: 30–2500 rpm Lsdpfjx Nxulex Aanshr Two-speed motor Motor power: 2/2.4 kW 16 spindle speeds Rohm 160 chuck Internal, external, and split jaws Spindle bore: 36 mm Tailstock quill: MK3 Quill travel: 100 mm Turning diameter: 320 mm Turning diameter over carriage: 190 mm Turning length: 650 mm Dimensions: 85x150x140 + 15 (pallet) Weight: 700 kg

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, Portal Machining Center – Universal – 5-axis machining Brand: AXA / Type: VPC-40-U / Year of construction: 2003 Description: Compact gantry design with overhead guides,automatic 1-axis swivel head and integrated NC rotary table for 5-sided machining. Condition: Ready for use / operational Operating hours (switch-on time): approx. 63.400 h TECHNICAL DATA Machining paths: - X-path (longitudinal movement): 2.300 mm vertical / 2.000 mm horizontal - Y-path (cross movement): 1.200 mm - Z-path (vertical movement): 600 mm - Distance between table and spindle nose: Zmin vert./hori. 110/160 mm - Rotary table – spindle nose: Zmin vert./hori. 110/160 mm Working table: - Table clamping surface: 1.100 x 1.100 mm - Table load: 1,5 tons Feed rates: - Max. Feed force: 9.000 N - Rapid traverse in X/Y/Z: 20/20/20 m/min Main drive / Spindle head: - Main drive AC – Hollow shaft motor 40 % ED: 30 kW - Speed range, continuously variable: 30 – 10.000 rpm - Tool holder: SK 40, DIN 69871A / 69872A Tool changer (chain magazine) - Tool stations: 36 positions Working spindle: 1-axis swivel head with 1° pitch Hirth spline instead of the standard 2.5° pitch. NC - Horizontal rotary table integrated into the machine table: - Rectangular face plate 1.100 x 1.100 mm EQUIPMENT / ACCESSORIES: - CNC-Control: Heidenhain iTNC 530 - Table height increase: fixed table by 150 mm. This means that the top edge of the fixed table and the rotary table are at the same height. - Coolant through the spindle - Chip conveyor (hinged belt) - Integrated 200 l coolant tank with pump for external cooling Lhjdpfsx Np Dqsx Aansr - Full machine enclosure - Extraction unit for extraction on both sides with work area enclosure - Manual spray guns - Electric hand wheel - Tool probe system TT 130, brand: Heidenhain There is no guarantee for correctness and completeness of the technical details and accessories. - Subject to prior sale - Detailed technical data sheet and information on equipment available on request.

Condition: ready for operation (used), Year of construction: 2012, VF - 2YT Year 2010 & 2011 - 3 units each & 2012 - 1 unit Travels S.A.E METRIC X Axis 30.00 in 762 mm Y Axis 20.00 in 508 mm Z Axis 20.00 in 508 mm Spindle Nose to Table (~ max) 24.0 in 610 mm Spindle Nose to Table (~ min) 4.0 in 102 mm Spindle S.A.E METRIC Max Rating 30.0 hp 22.4 kW Max Speed 10,000rpm Taper BT40 ATC 24 Lhjdpfxsx Hc Uqo Aaner Bearing Lubrication Air / Oil Injection Air / Oil Injection Cooling Liquid Cooled Liquid Cooled c/w RT-160 and RT-160-2 Rotary Table c/w Tool measuring system 7 units

Condition: new, color: grey, Field of application: Mining Empty weight: 32.000 kg Dimensions (LxBxH): 2200 x 310 x 430 cm Tyre size on axle rear: 225 Tyre tread remainder on axle rear: 100% MOBILE SAND MAKER Feeding Hopper : 10 m3 Crusher Feeding Belt Conveyor 800*9000mm VSI700 Vertical Shaft Impact Crusher 132kw Vibrating Screen 2 Decks 1600x5000mm 11 kw Feedback conveyor 600*8000mm Stockpile Conveyors 600*8000mm Mobile Chassis 2 Axles-Compacible With EU Road Regulations Automation -PLC- with Tablet and PC Controlled Industrıal Paint on 1 Layer Linings-120-140 Micron- Barriers-Ladders-Platfroms Galvanised PLANT DETAIL Production Capacity 40-60 tph 0-5mm Maximum Feeding Size 50mm Feeding Height 3.8 meters Main Configuration VSI Crusher + Vibrating Screen Total Motor Power 165 kW Electric Generator Requirement 350 kVA Weight of the plant 31 Tonnes Sizes of the plant 14(L) x 3 (W) x 4.2(L) meters Chassis Type Single chassis on wheels Production Capacity 100-150 tph Maximum Feeding Size 50mm FEEDER PROPER FOR HEAVY DUTY Dimensions : 900x4100 mm Bunker : 15 m³ Capacity : 150 to 200 tons / hour Grid Length : 1160 mm Main Body Sheet : 20 mm. Weight : 5.5 tons. Number of springs : 111 ea Type of Bypass : Flat grid type (throttle transfer) Lhjdpfx Aasx D A H Eonjr Grill casting : 16-18 mn. 1,5 cr. Type of Bunker : With flat ramp climbing Anchorage slots : pin click - fit Bypass chute : With rear additional saddle 2-Model : VSI 700 -CR Max Feed : 35 mm. Hard Condition Rotor Diameter : 760 mm. / Off Std. Rotor Rotor Speed : 50-70 m / s. Drive : 132 kW / 1500 rpm. Capacity : 40-60 tons / hour 0-5 sand production at 5-32 mm feed. Total Capacity : 80-120 tons / hour Weight : 8,500 kg Rotor Diamond Inserts (Two-row - 6 pcs Ductile Iron Tungsten Carbide Tipped) Other Wear Parts (2 Molybdenum, 22 Chrome Alloy Castings) Electric Motorized Hydraulic Unit (Used for Belt tensioning and Upper Body Lifting.) One-sided maintenance platform with ladder. Drive pulley for two separate speeds (1400 rpm - 1600 rpm) Vibration sensor switch Maintenance Crane Crusher Feeding Belt conveyor Rated sizes : 800 x 9000 mm Motor power : 7 kw 1500 d/d Power Transmission : Motorized Reducer Drive drum : 273 Vulcanized Rubber Coating Tail drum : Angle process over pipe Body Construction : Sheet Metal Body Rubber Tension System : SNH type sliding bedding Carrier : triplet assembly pedestal Group of turning roll : single hanger system Type of reducer : İ-MAK reducer Band rubber : 5 layers of 10 mm EP-125 eksaş conveyor Drive bearings : UCF type with...

Condition: new, functionality: fully functional, Year of construction: 2026, Model: FABO HY-600 Tip: Çift Helezyon Vidalı Yıkayıcı Lhsdpfx Aaewxyabensr Kapasite: 60 tph Boyut: 1400 x 6650x1800 mm Elek boyutu: Ø 600x6000 mm Hız: 22 rev/min Motor: 2 x 5.5 kW ağır hizmet Su tüketimi: 55-205 m3 Şasi, motor ve güvenlik korumaları dahil. *Tüm ürünlerimiz özenle üretilir ve 1 yıl garanti kapsamındadır! *Kurulum ve Operatör Eğitimi ÜCRETSİZ DAHA FAZLA BİLGİ İÇİN LÜTFEN BİZİ ARAYIN!!

Condition: ready for operation (used), Year of construction: 2017, Main Drive Number of axis 5 Spindle Speed 15000 RPM Spindle motor power 46 kW Tool taper SK 40 Movement X-Axis Movement 2600 mm Z-Axis Movement 900 mm Y-Axis Movement 1100 mm Control Unit Brand SIEMENS Model 840D sl This 5-axis DMG DECKEL MAHO DMF 260-11 was manufactured in 2017. A universal machining centre featuring a travelling column, X-axis linear drive at 80 m/min, and a motor spindle speed up to 15,000 min-1. It includes a swivel head, a 30-tool magazine, and a rigid table measuring 3,200 x 1,100 mm. Consider the opportunity to buy this DMG DECKEL MAHO DMF 260-11 universal machining centre. Contact us for more information about this machine. Lhedpex D Icljfx Aanjr Application Types Milling

Condition: used, Year of construction: 2000, operating hours: 15,800 h, Used Bottle Washer KLINGER up to 9600 bph This Bottle Washer handles up to 9,600 bottles per hour. The machine features 20 bottles per row, ensuring a long soaking time and double lye pumps. Constructed entirely of stainless steel, this bottle washer uses a Siemens S7 control system, ensuring reliable and precise operation. Lhjdpfxjxqmrfj Aansr Technical Specifications of the Washing System The Used Bottle Washer KLINGER up to 9600 bph includes double heaters and overflow pumps, providing a high cleaning capacity. Consequently, this configuration treats each bottle uniformly, enhancing the efficiency of the washing process. The Siemens S7 control system, furthermore, offers a user-friendly interface via a touch panel, simplifying operational management. Potable Water Treatment Plant Potable water treatment plays a crucial role in the proper functioning of the bottle washer. Hager + Elsässer provides the plant, which includes cation and anion exchangers, a salt container, a pre-filter, and a UV probe. This system processes 5 m³/h, ensuring high-quality water. Additionally, the reverse osmosis (RO) plant delivers a total desalination capacity of 2.5 m³/h, ensuring pure water for the washing process. Electrical Configuration and Control Panels This Bottle Washer features three electrical panels, arranged from left to right, with a Siemens touch panel for centralized control. This configuration allows for accurate monitoring and optimal operational management. In addition, the upper panels handle cooling, with a total residence time of 4.13 minutes and a treatment time of 1.63 minutes. Technical details Bottle cells: width and diameter: height 100 mm. 360 mm spray hole in the base of the cell diameter 20 mm. The bottle cell is not round on the lower insertion side, but flattened , so that even bottles with small diameters can be inserted into the cell without any problems. Bottles from 200 ml to 1,500 ml can be rinsed. The diameter of the bottle mouth must not be smaller than the spray hole in the bottom of the cell, i.e. at least 20 mm. If the bottles are very light, or made of PVC, the spray pressure of the pumps could be reduced using software, so that the bottles are not sprayed out of the cell. Fort PVC bottles the diameter of the bottles should not be smaller than 50 mm, depending on the shape and weight. The higher the weight, the better… PVC bottles do not cause problems because of their shape or diameter, but are usually too light… So your bottles can be easily worked. Treatment and Spraying Details of the Used Bottle Washer KLINGER up to 9600 bph The central panel, on the other hand, manages the spraying times with the following specifications: Spraying soda: 0.5 min. Residual soda: 0.83 min. Hot water: 0.38 min. Warm water: 0.38 min. Cold water: 0.38 min. Fresh water: 0.

Condition: used, Year of construction: 1995, space requirement length: 4,900 mm, power: 57 kW (77.50 HP), ELECTRICAL SPECIFICATIONS .. total power consumption: 57 kW .. mains voltage: 400 V .. mains frequency: 50 Hz DIMENSIONS / WEIGHTS .. space requirements -left/right-: 4900 mm .. space requirements -front/back-: 2600 mm .. total height: 2600 mm .. total weight approx.: 2600 kg Ledpfx Aaex Nvnvjnehr Washing medium: solvent-free basket/rack size 790 x 590 x 600 mm cabin dimensions 1200 x 1200 x 1200 mm useable volume 800 x 780 x 900 mm net weight of batch 200 kg Attachments: Dosing unit DOSANTEC A763-168M buffer tank 100 ltr Waste water tank 75 ltr rotating spraying cross from top rotating spraying cross from bottom Drying device (circulating air) with heat recovery 5 heating elements each 9 kW driven roller conveyor

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, Universal Machine Center Lhsdpfxowvra Ij Aansr 5 axis simultaneous DMG DMC 105V Linear Year 2007 Travel : X1050 Y 800 Z 560mm NC Rotary Table Ø1,000mm Heidenhain iTNC530 Control Spindle 18,000rpm ATC 30 HSK-63A NC B axis Control Milling Head – 120o / +30o Roto clear window Tool Measuring system – Blum Measuring probe Cooling by air blast through spindle by M code Spindle through coolant Chip conveyor ____Cheapest 1m 5axis_____

Condition: used, New: Yes Colour: Blue Field of application: Mining Empty weight: 35.000 kg Dimensions (LxBxH): 1400 x 400 x 250 cm Runnning hours: 16777215 mh Lhedpfxex D A E Ij Aanor Volume of the tank: 30 m^3 Capacity: 350 Productivity: 300 tph (1400 x 14000) Double Washing Screw: (With SKF AUTOMATIC LUBRICATION) Water Consumption : Minimum 100 Ton/Hour – Maximum150 Ton/Hour Capacity 300-350tph Screw Dimensions Ø1400 x 14.000 mm Motor :2x45/55 KW Drive System :Chained Drive System Roller : SKF Abbrasive : 6 mm on iron plate 10 mm Rubber Coated Discharge : Ø200 mm Pipe Discharge Channel : 2 PCS 120 mm 150 mm 5mm U Bend Platform : Ladder for Pre Maintenance and Safety Weight 35000kg Paint PPG or Jotun 2 Layer Paint on1 layer Epoxy Lining RPM 25 Degree 15 Dimensions 4400x15500x2600mm Housing Bearing Water Resistance SKF-FAG BEARING 6 PCS

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 40167, Auction of a MAHO universal milling machine! Lhedpox Ngkzefx Aanor

Condition: ready for operation (used), Year of construction: 2020, operating hours: 5,717 h, General Data Measurements width 2387 mm Measurements depth 3978 mm Measurements height 2565 mm Machine weight 8200 kg Control Unit Brand HAAS Main Drive Number of axis 5 Movement X-Axis Movement 762 mm Y-Axis Movement 508 mm Z-Axis Movement 508 mm Table Table load 300 kg Lhedox Hbmrspfx Aansr Media Chip conveyor Yes Additional Equipment Wireless Intuitive Probing System Through-Spindle Coolant This 5-axis HAAS UMC-750 was manufactured in 2020, featuring a 762 mm X-axis, 508 mm Y-axis, and 508 mm Z-axis. It includes a spindle speed up to 12,000 rpm, ISO 40 taper, and a robust 40-position tool changer. The machine supports a maximum table load of 300 kg and offers advanced features like a wireless probing system, chip conveyor, and through-spindle coolant. Consider the opportunity to buy this HAAS UMC-750 universal machining centre. Contact us for more information. Application Types Milling

Condition: good (used), Year of construction: 2004, functionality: fully functional, * CNC-control Heidenhain iTNC 530 * Number of Controlled Axes: 5 + spindle * NC-swivel-type rotary table, diameter 800 mm - Workpiece weight in clamped horizontal position 1000 kg - Positioning mode for both axes 600 kg (upper 30 deg. 500 kg) - 4-5 axes simultaneous mode 400 kg Lodpsx Nn U Ijfx Aanehr - Swivel range 45 deg. to the work spindle, 25 deg. away from the work spindle * 60-Position Tool Changer * Direct Measuring System, Resolution 0.001 mm * Coolant System (no coolant through spindle) * Chip Conveyor Technical details x-travel 800 mm y-travel 1000 mm z-travel 655 mm tool taper ISO 40 spindle turning speed range 0 - 15000 rpm feed range 10000 mm/min rapid traverse 30 m/min power capacity (100/40% ED) 18/24 kW total power requirement 40 kW weight of the machine ca. 10,5 t

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, DMG UNIVERSAL MACHINE CENTER DMU80P hi-Dyn Year 2001 X800 Y700 Z 600mm Heidenhain iTNC530 NC Rotary Table Ø900x630mm NC B axis Milling Head Spindle 18,000rpm Lhsdpfx Aajw A Dy Tenjr ATC 180 – HSK-A63 Roto Clear window Spindle thru' coolant 40 bar Selling Cheap Cheap sales - 50.000,00 USD

Condition: used, Colour: Red Field of application: Mining Take your material processing capabilities to the next level with Polygonmach’s Fine Material Washer. Known for their engineering excellence and innovative solutions, Polygonmach has yet again pushed the boundaries with their advanced Spiral Classificator and Screw Washer. Designed for maximum efficiency and performance, this system offers an unmatched processing solution for a variety of materials. The Polygonmach Fine Material Washer, also known as Spiral Classificator or Screw Washer, is a powerful tool for sand classification and dewatering duties. It is specially designed for washing, classifying, and dewatering fine material as well as for scrubbing and expelling clays and silts from raw materials. The design offers a high level of cleaning, improving the quality of your end product. While it is mainly used for cleaning and handling of sand and gravel, it also works with many other minerals. When you need the highest level of cleaning, this washer is your go-to solution. The Polygonmach Fine Material Washer's superior design ensures optimal performance. It features replaceable, wear-resistant paddles that enhance the machine’s longevity. The system also comes with an adjustable weir and water volume to meet your specific washing needs. Lhodpsx D A Dwefx Aaner To achieve the desired results, the Polygonmach Fine Material Washer is equipped with a heavy-duty design and construction. It is highly efficient, delivering precision, and accuracy in its operations. Despite its robust construction, it is easy to maintain and has low operational costs.

Condition: ready for operation (used), Year of construction: 2004, Control Unit Brand SIEMENS Model n/a Main Drive Number of axis 4 Movement X-Axis Movement 6000 mm X-Axis Rapid Traverse 60 m/min Y-Axis Movement 630 mm Y-Axis Rapid Traverse 60 m/min Ljdpfxsx Nr Iro Aanshr Z-Axis Movement 550 mm Z-Axis Rapid Traverse 60 m/min This 4-axis CHIRON Mill 6000 SK was manufactured in 2004, featuring a high-speed motor spindle at 12,000 rpm and a travel range of X 6,000 mm, Y 630 mm, Z 550 mm. It includes a 5-axis milling package, 92 tool positions, and a Marposs collision monitoring system. Ideal for long part machining up to 6,000 mm and pendulum machining. If you are looking to get high-quality milling capabilities consider the CHIRON Mill 6000 SK machine we have for sale. Contact us for more information. Application Types Milling

Condition: used, Field of application: Mining Explore the superior processing capabilities of the Polygonmach Coarse Material Washer, a state-of-the-art solution designed to exceed expectations in processing sand and gravel. Polygonmach, a leading name in the industry, constantly pushes the boundaries of innovation to bring high-quality, reliable solutions to businesses. The Polygonmach Coarse Material Washer is a fundamental tool in the industry, specializing in the thorough cleaning, classification, and dewatering of coarser fractions. Designed to handle robust materials such as sand and gravel, it significantly enhances the quality of your output, leading to increased customer satisfaction and business growth. Built with high-capacity processing in mind, our Coarse Material Washer employs powerful scrubbing technology. This action facilitates the removal of impurities, thus unlocking the true value of your raw materials. The result is high-quality end products that meet rigorous industry standards. One of the key features of the Polygonmach Coarse Material Washer is its replaceable heavy-duty paddles. These are engineered to withstand the harsh environment, thereby increasing machine lifespan and reducing maintenance costs. The robust design is well-suited to large-scale operations, delivering high-volume processing efficiently. Lhjdpfxjx Dh S He Aaner Moreover, it comes with an adjustable weir plate that offers control over the water volume and the fines. This flexibility empowers you to produce materials of desired specification and moisture content, guaranteeing consistent product quality. The Coarse Material Washer from Polygonmach is not only highly functional but also user-friendly.

Condition: ready for operation (used), Year of construction: 2008, operating hours: 46,380 h, Main Drive Number of axis 5 Spindle Speed 14000 RPM Spindle motor power 19 kW Tool taper SK 40 Movement X-Axis Movement 500 mm Z-Axis Movement 400 mm Y-Axis Movement 450 mm Control Unit Brand HEIDENHAIN Model iTNC 530 Tools Slots in storage 30 This 3+2-axis DMG DMU 50 was manufactured in 2008, featuring a Heidenhain ITNC 530 control system and a spindle speed of 10,000 rpm. It includes a 30-position tool changer and a rotary table. IIf you are looking to get high-quality milling capabilities, consider the DMG DMU 50 machine we have for sale. Contact us for more information. Ledpfxox Nknwj Aanohr Application Types Milling

Condition: ready for operation (used), Year of construction: 2019, Main Drive Spindle speed range 35 – 12000 Number of axis 5 Lhjdpfx Aex D Hx Eoansr Movement X-Axis Movement 350 mm Y-Axis Movement 550 mm Z-Axis Movement 510 mm Table Table load 300 kg This 5-axis Mazak Variaxis i-500 was manufactured in 2019, featuring a spindle speed of up to 12,000 rpm and a tool magazine capacity of 30 tools. It supports workpieces up to Ø500 mm by 350 mm and has a table load capacity of 300 kg. Consider the opportunity to buy this Mazak Variaxis i-500 universal machining centre. Contact us for more information about this machine. Application Types Milling

Condition: ready for operation (used), Year of construction: 2008, Main Drive Lhsdpfxex D Hpwe Aanor Number of axis 5 This 5-axis DMG DECKEL MAHO DMU 70 eVo was manufactured in 2008. Consider the opportunity to buy this DMG DECKEL MAHO DMU 70 eVo universal machining centre. Contact us for more information. Application Types Milling

Condition: ready for operation (used), Year of construction: 2018, General Data Measurements width 2700 mm Measurements depth 10800 mm Measurements height 3100 mm Machine weight 16000kg Lhsdex D E Tzepfx Aanor This 5-axis RASOMA EBZ 200-500 was manufactured in 2018, featuring a robust 16,000 kg weight and comprehensive dimensions of 10800 × 2700 × 3100 mm. It includes a high-performance tool spindle with a 7.5 kW Siemens motor, capable of speeds up to 2000 rpm, and advanced cooling and hydraulic systems ensuring efficient operation. If you are looking to get high-quality milling capabilities consider the RASOMA EBZ 200-500 machine we have for sale. Contact us for more information about this machine. Application Types Milling