Used hydraulic presses double column / four column presses for sale (238)

Year of construction: 2001, condition: excellent (used), Used hydraulic press SACK & KIESSELBACH TRP 200. The originally automatic transfer press was converted to manual in 2012, but can be converted again as an automatic press. The press is still set up and under power and is in very good condition. Pressing capacity in t: 200 Quantity of oil in l: 1100 Stroke in mm: 300 Table size (lxb) in mm: 600 x 600 Daylight in mm: 1000 Upper ejector stroke in mm: 25 Fodshfwqzepfx Aatspl Upper ejector force in t: 10 Total weight in kg: 12000 Operating pressure in bar: 6 Approach speed in mm/sec: 375 Working speed in mm/sec.: 18 - 40

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke Fpedpfx Aew A Amrsatjl - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed - Blow-off device electrically pre-wired, without air valve - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: used, Machine not operational - control system not functioning Available at a special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Factory No. 300487, Year of Manufacture 2006 Pressing force: 500 tons Distance between columns (front and rear): 2520 mm Table area: 2500 x 2500 mm Ram area: 2500 x 2500 mm Ram stroke: 600 mm Maximum installation height: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable forward speed: 100-800 mm/s Pressure build-up to 5000 kN: approx. 0.7 sec. Return stroke speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-fold flat guide for the ram - Hydraulic ram locking in the top dead center position - Adjacent control cabinet (200 x 50 cm) - Electrical control system SIEMENS PLC S7-314 - Operation via SIEMENS OP 170-B (5.7") - 2-hand control panel located beside the machine - Floor-level installation - Table top 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication system - Operating manual with circuit diagrams Space requirement (L x W x H): 372 x 260 x 460 cm Space requirement for horizontal transport (L x W x H): 460 x 372 x 260 cm Fodpfsdzqptsx Aatopl Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: used, Double-column hydraulic press SCHÖN Type UTE/B 50 Machine No. 5509 Year of manufacture: 1971 Pressing force: 50 tons Column span: 550 mm Column clearance (side): 150 mm Table size: 480 x 380 mm T-slot width in machine table: 18 mm Table opening: Ø 70 mm Ram area: 490 x 280 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 150 mm Max. installation height: 390 mm Table height above floor: 890 mm Rapid approach speed: approx. 130 mm/sec Working speed: approx. 20 mm/sec Return speed: approx. 130 mm/sec Motor power: 4 kW Power supply: 380 Volt, 50 Hz - Stepless pressing force adjustment - Rapid and working stroke - Pressure or stroke-dependent stroke limitation - Adjustable pressure holding time, press time extension 0.5–6 s - Mechanically adjustable hard stop via handwheel on ram - SICK light barrier, Type LVU - Stroke counter - Double column guide on ram Space requirement (L x W x H): 1100 mm x 1050 mm x 2320 mm Weight: approx. 1.5 tons Good condition Fpsdpjv Srfwofx Aatol

Condition: used, Double-column hydraulic press, NEFF type RHS 125 Z Hydraulic drawing press Machine no. 3973, year of manufacture 1983 Pressing force 125 tons Column width 1050 mm Column opening, side 550 mm Table area 1000 x 800 mm Ram area 1000 x 800 mm Ram stroke 350 mm Installation height max. 750 mm Table height above floor 960 mm Drawing cushion force approx. 12 tons at 105 bar Drawing cushion stroke 100 mm Through-hole in the table Ø 202 mm Rapid traverse speed, downward approx. 360 mm/sec Rapid traverse speed, upward approx. 360 mm/sec Working speed approx. 36 mm/sec Oil tank capacity approx. 1000 liters Motor power, main pump 22 kW Motor power, control pump 4 kW Motor power, control pump 2.2 kW Power connection 400 volts, 50 Hz - Hydraulic drawing cushion under the table with a hole through the table plate Ø 202 mm - Precise 4-way column guidance on the ram corners - Stepless pressing force adjustment - Adjustable fixed stop, electrically controlled via a hydraulic motor Fjdpfeguvtlsx Aatepl - Stroke damping - 2-hand control panel for releasing the lifting motion on the press - Control cabinet positioned next to the press (1600 x 500 mm) - Documentation including operating manual, electrical wiring diagram, and PLC program printout available Space required for the press L x W x H 2600 x 2400 x 4270 mm Weight approx. 14 tons Good condition

Condition: used, Year of construction: 2006, machine/vehicle number: 18282, Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Fedpfxouqd S Ao Aatopl Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l

Condition: used, Year of construction: 1996, machine/vehicle number: 14.194, Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Fpsdeu Saaaspfx Aatsl Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.

Condition: used, Year of construction: 1989, Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Fjdpfx Aaouqdi Uetopl Required power: 450 kW Weight of machine approx.: 240 ton Standard configuration with hydraulic tool clamps on the ram

Condition: used, Year of construction: 2002, machine/vehicle number: 10857, Pressure total: 315 ton Stroke: 1100 mm Daylight: 2200 mm Table surface area : 2500 x 1000 mm Slide area: 2500 x 1000 mm Die weight at the ram max.: 6000 kg Approach speed: 600 mm / sec Working speed: 32 - 230 mm / sec Return speed: 600 mm / sec Required power: 158 kW Weight of machine approx.: 44 ton Height over floor approx.: 6175 mm Fpjdpfx Aaevmfzbotjl Automation

Condition: used, Year of construction: 1986, Pressure total: 500 ton Stroke: 1100 mm Daylight: 1500 mm Table surface area : 2000 x 1250 mm Slide area: 2000 x 1250 mm Die cushion capacity in table: 160 ton Die cushion stroke: 300 mm Fpjdpouqdqljfx Aatel Approach speed: 650 mm / sec Required power: 55 kW Weight of machine approx.: 50 ton Standard configuration The press was completely overhauled mechanically, hydraulically and electrically in 2008.

Condition: used, Year of construction: 2006, machine/vehicle number: 18282, Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Fjdpfxsuqd Nuj Aatepl Oil volume: 700 l

Condition: good (used), Year of construction: 1973, pressing force: 315 t, table width: 1,500 mm, table length: 2,500 mm, Hydraulic 4-column press, manufacturer FIBRO, year of manufacture 1973, pressing force 315 t. Dimensions approx. 3.0 m × 1.6 m × 4.5 m. Table size: 2.5 m × 1.5 m. Fodpfx Ajx Nhakeatspl Separate hydraulic unit and control panel. Maximum working area 883 mm (ram fully retracted). Powered, can be inspected on site. All information has been provided to the best of our knowledge and belief. Subject to change, errors, and prior sale.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, pressing force: 700 t, stroke length: 1,500 mm, overall weight: 50,000 kg, Equipment: documentation/manual, Press used for composites, until now it worked in Belgium. In July 2015 the press underwent a thorough modernization, the year of production of the device is 1990, however the modernization was very extensive. The press was used very little, it worked in a research institute. Due to the power cut, I could not check the mileage, but the device looks like new, there are no signs of wear of the working elements. The press is currently in Poland, 63-300 Pleszew, Poland. Pressure 700T. Dimensions of the upper foot 180x240. Foot stroke approx. 150cm. The press was used to develop the famous carbon space frame AUDI R8, it worked in a research and development institute near Brussels. Fpedpfxewtbc Tj Aatjl Sometimes this device was also used for commercial production. The press looks practically like new. I have full modernization and technical documentation. The device was dismantled by me, in the sale price I add free assembly at the customer's, I will restore the device to the condition it was in before I dismantled the press. The buyer must provide a large forklift (approx. 44T), compressed air, and accommodation for 3 people for 14 days. I offer and pay for a team to assemble the device on site throughout Europe. It is very likely that the device will have to be configured for operation at the new buyer's, this task can be performed for an additional fee by a company from the Netherlands, which carried out a thorough modernization of the device in 2015, the estimated cost of such an operation depends on the buyer's requirements. The transport costs will be very attractive, because I have a friendly company that has very attractive delivery terms for me. The weight of the entire device is approximately 50T.

Year of construction: 1990, condition: reconditioned (used), Hydraulic press - has 4 independent stroke / cylinders. Deep drawing process. Fodpfx Aaegcvfnjtopl Manufacturing of oil and fuel filters cans. The range of details is: Sheet thickness: 0.4-0.6 mm Material type - black or galvanized steel Can diameter: 68mm - 96mm Can length: 50mm - 180mm The entire control was replaced, including cabling, drivers, monitor, etc.

Year of construction: 1993, condition: used, TYPE: DEA 400/2000 Year: n.d. MAXIMUM RAM CAPACITY: 400 tons SLIDE STROKE: 1,100 mm MAXIMUM SHUT HEIGHT: 1,600 mm TABLE DIMENSIONS: 2,000 x 1,600 mm FAST STROKE: 650 mm/sec CUSHION CAPACITY: 160 tons CUSHION STROKE: 400 mm HEIGHT ABOVE GROUND: 5,800 mm DISTANCE BETWEEN UPRIGHTS: 3,400 mm Fpodpfoihf R Uox Aatol LATERAL WINDOW: 1,600 mm

Condition: excellent (used), functionality: fully functional, Manufacturer: MURARO Model: ID500/250 Year: 2001 Condition: Used Stock number: Code 0114 Fedpfex R U R Ejx Aatjpl Maximum upper slide pressure: 500 tons Slide stroke: 900 mm Maximum daylight: 1,500 mm Table size: 2,700 x 1,600 mm Slide dimensions: 2,700 x 1,600 mm Blank holder table size: 2,450 x 1,250 mm Approach speed of slide: 650 mm/sec Blank holder cushion – total force: 250 tons Lower blank holder stroke: 400 mm Overall press height from floor: 5,600 mm

Condition: good (used), functionality: fully functional, pressing force: 1,500 t, stroke length: 1,320 mm, table width: 2,440 mm, table length: 4,572 mm, clearance between the columns: 4,800 mm, die cushion stroke: 360 mm, Equipment: documentation/manual, Manufacturer Muller Model BZE 1500 Year 1980 Excellent condition Stock number cod.0313 Thrust: 1500 ton. Thrust points: no. 6 Slide stroke: 1320 Maximum sled opening:m 2,620 mm. Fodpfx Aajq Hdz Uetspl Maximum slide closure:m 1,300 mm. Slide size: no. 6 Table size: 4,572 x 2,440 mm. Stroke premiums bottom plate: 360 mm. Useful front passage: 4,800 mm. Lateral passage in the shoulder: 2,600 mm. Pull-out carriage with possibility in the upright Location :Italy

Condition: like new (used), Year of construction: 2018, functionality: fully functional, Pressing force 300 to Stroke 500 mm Area between the columns 1250x1000 mm Installation height 1000 mm Rapid traverse 22 mm/s Working speed 2 mm/s Motor 7.5 kW Length 2000 mm Width 1500 mm Height 3300 mm 4-column guide Round ram guide Table and ram with T-slots 2-hand operation Operating instructions Siemens touchscreen control and electric control panel NEW , 50 programs storable, for programming of: - Upstroke and downstroke rate - Pause time in the floor - Decompression time - Setting the working pressure - Piece counter - Prestop in upward and downward movement - Setting for manual and automatic movement - Management of alarms and anomalies Fjdpfx Aajvgncnotjpl

Condition: refurbished (used), Year of construction: 1997, machine/vehicle number: 4290, functionality: fully functional, pressing force: 30 t, stroke length: 300 mm, table width: 440 mm, table length: 320 mm, total height: 2,750 mm, Fully refurbished Schoen double-column press, manufactured in 1997/2025. Press force: 300 kN Fpodpfx Aoy Uv T Ajatsl Installation height: 500 mm Stroke: 300 mm Table: W x D 440 x 320 mm Machine will be fully refurbished: - new control system - new light curtain - hydraulic system overhaul.

Condition: used, Pressing force 400 kN ,Table 450x560 ,Ram 375x300 ,Distance table-joints 340 stroke 160 ,Through-feed hole 100 diameter ,Safe column passage 220x410 Fpedpoum Uuysfx Aatsl

Year of construction: 1984, condition: used, pressure 100 t distance between columns 1000 mm stroke 150 mm table surface area 1000 x 700 mm distance table/ram 500 mm die cushion stroke 180 mm ram surface 1000 x 700 mm ram drills x depth 50 mm no. of strokes 85 Hub/min tool shank hole (depth x diameter) 85 x 50 mm clamping slots 22 DIN 650 form diagonal number of clamping slots 2 sheet width 400 mm plate length 1000 mm dimensions of the machine ca. 3,0 x 3,0 x 3,0 m weight of the machine ca. 8 t total power requirement 30,2 kW - fine adjustment of stroke - cutting impact damping - oil extraction Fpodpfx Aasfn Apzetol - 2 cylinders - roller feed, make Dreher, type WAV, control PMS3000 - soundproof cabin - machine was overhauled in 2001 and with new control SIEMENS SIMA-TIC OP17 equipped

Year of construction: 1981, condition: used, pressure 40 t distance between columns 600 mm stroke 160 mm table-size 560 x 400 mm dayligth 360 mm ram hole 40 H 7 DIN 810 mm oil volume 500 l return speed 200 mm/sec die cushion hydr. pressure/stroke 60 capacity of ejector 25 t total power requirement 15 kW Fodpfxjb U Hw Tj Aatopl dimensions of the machine ca. 1.44 x 0.95 x 2.54 m pressing speed 27 mm/sec return speed 200 mm/min

Year of construction: 1980, condition: used, pressure 100 t Fpsdpsdlxctjfx Aatol distance between columns - mm stroke 350 mm table size 1150 x 700 mm total power requirement 11 kW weight of the machine ca. t dimensions of the machine ca. m - cutting impact dampening - die cushion - without electrical cabinet

Condition: good (used), Year of construction: 1994, functionality: fully functional, operating hours: 25,000 h, pressing force: 400 t, table width: 1,250 mm, table length: 1,240 mm, table height: 1,125 mm, oil tank capacity: 3,400 l, total width: 3,500 mm, total height: 4,600 mm, installation height: 600 mm, Further images and technical data can be provided by email upon request. Sale is ex-location without warranty and return. Dismantling and collection must be carried out by the buyer. The press is standing at ground level without a base. We deliver the press media-free. The digital hours counter is no longer accurate. The manual counter shows approximately 25,000 hours. Fsdpfx Aasvb D Tretepl

Condition: good (used), Year of construction: 2015, functionality: fully functional, pressing force: 2,500 t, table width: 2,500 mm, table length: 5,000 mm, total length: 8,000 mm, total width: 8,000 mm, total height: 9,000 mm, overall weight: 55,000 kg, Equipment: safety light barrier, LOIRE SAFE Hydraulic Press – High-Performance System for Toolmaking and Heavy-Duty Forming This high-performance hydraulic press in a robust 4-column gantry design has been specifically engineered for demanding applications in toolmaking (tryout/spotting) as well as for large-format forming processes. The stress-relieved, annealed welded construction ensures maximum rigidity and long-term process stability. The machine is equipped with three main cylinders featuring multi-cylinder parallel control, achieving high repeat accuracy within ±0.1 mm. Its powerful hydraulic system, based on Bosch Rexroth components, operates at a maximum working pressure of approximately 450 bar, enabling precise and forceful processing. Control is provided via a Siemens S7-317F PLC, combined with servo-controlled axes (Rexroth MLC) and visualization via Siemens WinCC. This setup allows for fully programmable press cycles, storage of tool parameters, and user-friendly operation with diagnostics and fault monitoring. In terms of safety, the press is comprehensively equipped: light curtains at the front and rear (Category 4), ram parallelism monitoring, emergency stop with defined response time, and optional two-hand operation ensure maximum operational safety. The system is CE-compliant and meets current safety standards. Features include a hydraulic, three-section draw cushion, a hydraulic ram cushion, as well as a movable table with approximately 4,000 mm stroke. The machine is complemented by a DIN-standard ram plate and integrated cutting impact damping for challenging forming processes. Fpsdpfx Ajyw Ah Eeatsl Toolmaking (Tryout / Spotting)