Used Combined Drawing for sale (5,124)

Condition: used, Year of construction: 1993, Pressure 250 t stroke 500 mm distance between columns 1650 mm side window 750 mm daylight 1200 mm table surface area 1650 x 1250 mm die cushion capacity in table 80 t die cushion stroke in table 250 mm die cushion area in table 1070 x 780 mm table height over floor 850 mm ram surface 1650 x 1250 mm speed down 10 mm/s speed up 80 mm/s working speed 10 mm/s oil volume 400 l power requirement 22,0 kW Weight 21,5 t dimensions (WxDxH) 2,7 x 2,3 x 4,25 m height above floor 4,0 mm Iedpfx Absv Svb Ajcetd permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, controllable dependent on pressure and way, hydraulic drawing cushion in table, hydraulic cutting impact cushioning (4x Parallel holding cylinders), two-hand operation, hand lever operation

Condition: used, Year of construction: 1972, Pressure 800 t distance between columns 3250 mm stroke 1100 mm Distance table/ram, stroke up 1900 mm Table surface area 3100 x 1900 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 300 mm Die cushion area in table 2500 x 1800 mm Die cushion pressure in ram 80 t Die cushion stroke in ram 200 mm Iedpovuuhysfx Abcstd Die cushion area in ram 2200 x 1000 mm Ram surface 3100 x 1900 mm Side window 900 mm Oil volume 4700 l Power capacity 200,0 kW Dimensions (WxDxH) 4,95 x 3,3 x 10,2 m Height above floor 7,05 m with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, Year of construction: 1973, Pressure 1600 t distance between columns 4100 mm slide stroke 1450 mm Distance table/ram, stroke up 2750 mm distance table/blank holder, stroke up 2200 Table surface area 4000 x 2200 mm ram pressure 1000 t Itodpfjvut Ifox Abced Pressure of blank holder 600 t stroke of blankholder 1000 mm blank holder surface 4050 x 2200 mm Ram surface 3200 x 1650 mm pressure of drawing cushion in table 360 t Die cushion stroke in table 300 mm die cushion area 3500 x 1600 mm Side window 1100 mm Oil volume 9000 l Power capacity 390,0 kW Weight 250,0 t Dimensions (WxDxH) 5,95 x 4,3 x 10,5 m Height above floor 8,6 m with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram stored in dismantled condition - Video at seller’s site before dismantling available

Condition: excellent (used), Year of construction: 2022, For sale is a used Hammer A3-31 planer-thicknesser with a planing width of 310 mm. The machine is in very good condition and has been reconditioned and checked by our specialist staff. (Fully functional) Technical data: - Planer-thickness width 310 mm - 3 knife shafts (reversible knives) - Thickness height 4-225 mm - Dual foldable planer tables - Pivoting planer stop Itedpfx Aev Ianxjbced - 2.9 kW / 4 HP motor / 400 volts - Year of manufacture 2022 The machine is located in A-8561 Söding and can be inspected at any time during our opening hours. Subject to prior sale! Related terms: planer, thicknesser, planing machine, planing, thicknessing Reference: R-AT0YY

Condition: new, Year of construction: 2026, control type: CNC control, KBA - Combined CNC-controlled press brake / guillotine shear Super-compact machine with a very small footprint. Iedsyhzltjpfx Abcjtd Maximum cutting length: 3,020 mm or 2,020 mm Rated cutting capacity: 6 mm steel sheet / ST 40 Cutting angle: 1°30″ Backgauge for the shear station – adjustment range: 750 mm Table height: 750 mm Maximum bending length between side frames: 3,550 mm or 2,505 mm Maximum pressing force: 1,000 kN Working height for bending: only 1,230 mm Stroke range (bending station): 175 mm Maximum installation height (bending station): 350 mm Backgauge adjustment range (bending station): 750 mm Dimensions including operator’s pendant: 4.25 or 3.25 m x 1.82 m x H 2.8 m Required floor space: 3.85 or 2.85 x 1.82 m Drive power: 10 kW Weight: 9,000 kg or 7,500 kg Equipment: - CNC control with touchscreen and 10” colour display, graphical user interface, and automatic bending angle calculation - 1 set of press brake tools (bending punch + four-way reversible die) - Sheet metal supports for the press brake station - 90° angle stop for the guillotine shear with 1 m length - Bending station working area safeguarding via light barriers, rear area safeguarded by lateral safety guards and light barriers Optional: - Front bending area guarding by PILZ® camera monitoring - Rotatable angle stop

Condition: ready for operation (used), System includes (1) Two-Cylinder Motor HERFORD 2H 280, power: 150PS, rotational speed: 400/min, electric/ heating power: 83/ 140kWh, with Generator MARELLI MJB 250 LE4 (2) Three-Cylinder Motor HERFORD 3H 280, power: 225PS, rotational speed: 400/min, electric/ heating power: 125/ 212kWh, with Generator MARELLI MJB 250 MA4. Itodsgg Stfopfx Abcod

Condition: like new (used), spindle diameter 35 mm 5 speeds from 3,000 to 10,000 rpm motor power 5.5 kW Isdpfsyfua Ujx Abcjtd Maggi 4-roller feed with stepless speed control tenoning carriage with angle setting scale worktable 120x730 cm 760 kg year of manufacture 2001 can be purchased without feed unit

Condition: as good as new (ex-display), SHOWROOM MACHINE For sale is an as-new Record Power PT 107 planer-thicknesser with a planing width of 265 mm. The machine is in original condition, so you receive the full warranty. Technical specifications: - Planing width: 265 mm - Planing table length: 1,110 mm - Max. planing depth: 3 mm - Tiltable fence up to 45° - Cutterblock diameter: 75 mm - Large 3-knife cutterblock - Speed: 4,000 rpm - Max. thicknessing height: 190 mm - Thicknessing infeed width: 265 mm - Feed speed, thicknesser: 5 m/min - Max. depth of cut, thicknesser: 2 mm - Motor: 2.3 HP / 230 V Itedpfx Aeuv Exiobcjd - Power consumption: 2,200 watts - Extraction port: 100 mm - Weight: 162 kg One unit of this planer is available at both A-5431 Kuchl and A-8561 Söding, and can be inspected at any time during our opening hours. Subject to prior sale! Freight shipping: Austria: €70 incl. VAT Germany: €90 incl. VAT South Tyrol: €130 incl. VAT Related terms: planer, thicknesser, planer-thicknesser, surfacer, thickness planing Reference: ZXPT107-A

Condition: like new (used), Year of construction: 2023, For sale is a used Hammer A3-41 planer-thicknesser with a planing length of 1800 mm. The machine has been checked by our specialist staff and is in mint condition. Technical data: - 3 system knife planer shaft - Planing width 410 mm - Planing length 1800 mm - Max. passage 230 mm - Motor power 4 kW / 5.4 HP - Extractable Ø 120 mm - Year of manufacture 2023 Itjdpjv Dah Defx Abcod - Mint condition The machine is located in A-5431 Kuchl and can be inspected at any time during our opening hours. Related terms: planer, thicknesser, planing machine, planing, thicknessing Reference: R-A0117-1

Condition: excellent (used), For sale is a used Hammer A3-41 Silent Power surface planer and thicknesser with a jointer length of 1800 mm. The machine has been checked by our specialized staff and is in very good condition. Technical data: - Silentpower spiral cutterhead - Planing width 410 mm - Jointer length 1800 mm - Max. clearance 230 mm - Motor power 4 kW / 5.4 HP - Suction connection Ø 120 mm - Year of manufacture 2022 The machine is located in A-5431 Kuchl and can be inspected at any time during our opening hours. Related terms: jointer, thickness planer, planer, jointing, thickness Reference: R-A0117 Itodpfswqq Dhex Abced

Condition: used, Year of construction: 1993, Pressure 1500 t distance between columns 5050 mm stroke 1100 mm Distance table/ram, stroke up 2300 mm Table surface area 5000 x 2700 mm pressure of drawing cushion in table 320 t Die cushion stroke in table 300 mm Die cushion area in table 4300 x 1830 mm Die cushion pressure in ram 120 t Die cushion stroke in ram 200 mm Die cushion area in ram 3410 x 1650 mm Ram surface 5000 x 2400 mm Speed down 360 mm/s Speed up 168 - 505 mm/s Working speed 19 - 86 mm/s Oil volume 10500 l Power capacity 450,0 kW Weight 400,0 t Dimensions (WxDxH) 3,47 x 6,95 x 12,21 m Height above floor 8,21 m Height below floor 4,0 m year of manufacture 1983 - overhaul 1993 with oilhydraulic drive, drawing cushion in table, drawing cushion in ram (drawing cushion surface) approx. 3410 x 1650 mm), cutting impact cushioning / stroke limitation (adjustment of the spindle approx. 500 mm, max. dampening force approx. 750 t, dampening stroke max. approx. 30 mm), controllabel dependant on pressure/time and way Itjdpfx Aevuucqebcjd as is where is, WITHOUT dismantling, WITHOUT loading

Year of construction: 1987, condition: ready for operation (used), An old Schumag Aachen drawing machine without control is available. Drawing force: 100kN, drawing speed: 80m/min, material diameter range: 25mm-43mm. On-site inspection is possible. Itsdpov Tctuofx Abcjd

Condition: ready for operation (used), Year of construction: 1961, A Niehoff slide-free drawing machine is available. Processing diameter: 5mm-15mm, drawing speed range: 6m/min-24m/min, gearbox: manual gearbox, machine dimensions X/Y/Z: approx. 2600mm/2200mm/4000mm, weight: approx. 6500kg. The gearbox was completely overhauled in 2019 with new gears and new bearings. A new external lubricating oil pump was also installed in the same year. Documentation available. On-site inspection is possible. Itedpfx Aowq R N Rjbced

Condition: ready for operation (used), Year of construction: 2016, Fuel: natural gas (NG), engine: HMG, space heating unit with CHP: yes, condensing boiler: no, additional heating unit: no, low-temperature boiler: no, B11 boiler: no, combi unit: no. Rated heat input P: 88kW, annual efficiency of the space heating system η: 136%, energy efficiency class: A++, usable heat output at rated heat input with additional heater switched off/on: 87.9kW, thermal efficiency at rated heat input with additional heater switched off/on: 57.5%, electrical efficiency at the heat output of the space heating unit with CHP with additional heater switched off/on: 33.5%, auxiliary power consumption at full load/part load el: 1.132kW, in standby mode P SB: 0.06kW, standby heat loss P stby: 0.442kW, annual energy consumption Q HE: 1345kWh, sound power level indoors L WA: 72dB, operating hours: 42,892h. Water was detected in the oil circuit, the unit has an oil-related fault despite sufficient oil being present, and it also shuts down with the message 'engine too hot'. The control unit was overhauled by the manufacturer in 2024, and regular maintenance intervals for oil changes, spark plugs, valves, etc. have been carried out. With documentation. Itsdpfx Abexc Ni Rocsd

Year of construction: 2017, condition: ready for operation (used), A spinning, drawing and winding line for the production of monofilament yarns, multifilament FDY and POY is available. Spinning positions: 24, yarn ends: 192, drafting: cold and hot godets, package change: without yarn breakage, number of godets heated/cold: 50/50, number of winders: 24 (+2 reserve winders). Including various spare parts for the machine and electronics. Documentation available. On-site inspection is possible. Ijdpfx Abeuanq Tecotd

Year of construction: 1996, condition: ready for operation (used), A large-format vacuum thermoforming machine Geiss is available. Heating capacity: 180kW, forming area X/Y: 1600mm/1000mm, drawing depth: 620mm, quick-clamping system: 640mm, window plate adjustment: 250mm-750mm, drilling grid: 50mm, closing force: 50kN. Documentation available. An on-site inspection is possible. Expected to be available from February 2026. Ijdpfxjxwyvks Abcstd

Year of construction: 2008, condition: ready for operation (used), A Geiss large-format vacuum thermoforming machine is available. Panel cutting min.: 1100mm/1300mm, max. panel cutting: 2100mm/1800mm, max. forming depth: 620mm. Additional panel format 1: min.: 850mm/750mm, max.: 1850mm/1250mm. Additional panel format 2: min.: 1050mm/800mm, max.: 2050mm/1300mm. Including a separate loading machine with pneumatic panel separating equipment, an automatic aligner for panel cuts in longitudinal and transverse direction, a pneumatic pusher for removing the molded parts from the loading unit, fully automatic central lubrication of the loading machine, several interchangeable pallets for window panel sets, a storage rack for window panels as well as a vacuum control with four independently adjustable flow stages and an air preparation system. Documentation available. On-site inspection is possible. Ijdpfxswih Aro Abcstd

Year of construction: 2021, condition: ready for operation (used), A semi-automatic vacuum skin packaging machine (tray sealer) Sealed Air for Darfresh skin packaging is available. Packaging capacity: 15/min, cycle performance: 1.5 cycles/min, film width: 562mm, max. product dimensions X/Y/Z: 670mm/470mm/50mm, tray length range: 135mm-700mm, tray width range: 120mm-520mm, tray height range: 5mm-50mm. Machine dimensions X/Y/Z: approx. 1050mm/1650mm/1250mm, weight: approx. 500kg. Documentation available. An on-site inspection is possible. Ijdpfx Asxaphbobcetd

Year of construction: 2002, condition: ready for operation (used), Offered is a thermoform vacuum packaging machine / deep-drawing packaging machine from CFS. Air: 8bar / 500Nl/min, water: 2bar / 75l/min, weight approx. 2800kg. Inspection by arrangement possible. Iodpoxx Ud Ejfx Abcstd

Condition: ready for operation (used), A combined heat and power unit (CHP), consisting of three diesel generators installed in containers, is available. 1) Engine: MAN 12-cylinder turbo, type: D 2842 LE 20, generator: Krauter, type: D-SYN-GEN, kVA: 400, kW: 360, A: 577, Hz: 50, speed: 1500 rpm. Including DELF synchronization, heating water outlet, table cooler, preheating and oil change device. 2) Engine: MAN 12-cylinder turbo, type: D 2842 LE 20, generator: Leroy-Somer, type: LSA K 475 L10, kVA: 375, kW: 300, A: 400, Hz: 50, speed: 1500 rpm. Including DELF synchronization, heating water outlet, table cooler, preheating and oil change device. 3) Engine: Daimler Benz 8-cylinder turbo, type: AGV 12, generator: Krauter, type: D-SYN-GEN, kVA: 350, kW: 230, A: 400, Hz: 50, speed: 1500 rpm. The combined heat and power unit has a total output of around 1100kVA. Including table cooler, V2A heat exchanger, containers and switch cabinets. All generators are installed in containers and are therefore easy to transport. Iedpfxstwqzre Abcstd

Condition: used, Year of construction: 1999, Pressure 400 t stroke 800 mm distance between columns 2820 mm Side window 950 x 1100 mm distance table/ram (stroke up) 1600 mm table surface area 2800 x 1200 mm die cushion capacity in table 150 t die cushion stroke in table 200 mm die cushion area in table 2000 x 800 mm table height over floor 650 mm ram surface 2800 x 1200 mm speed down 420 mm/s speed up 300 mm/s working speed 17,5 - 29,5 mm/s oil volume 2500 l power requirement 75,0 + 22,0 kW Weight 50,0 t dimensions (WxDxH) 4,1 x 2,8 x 7,2 m height over floor 6,15 m Itsdpfxov Sva Ss Abced permitted for manual loading according to the CE-norm with oil-hydraulic drive, controllable dependent on pressure/time and way, hydraulic drawing cushion in table, hydraulic ram interlocking, two-hand and four-hand operation

Condition: used, Year of construction: 1983, pressure 500 t distance between columns 2240 mm stroke 1180 mm distance table/ram, max. stroke up, adjustment up 1800 mm table surface area 2050 x 1800 mm pressure of drawing cushion in table 250 t stroke of drawing cushion in table 380 mm drawing cushion surface in table 1800 x 1200 mm pressure of drawing cushion in ram 122 t stroke of drawing cushion in ram 200 mm drawing cushion area in ram 1800 x 1200 mm ram surface 2215 x 1800 mm table height over floor 500 mm speed down 400 mm/s speed up 10 - 400 mm/s working speed 10 - 100 mm/s height over floor 6,8 m depth of the foundation 3,0 m power requirement 120 kW weight 110,0 t Iodpjvuk Tlsfx Abcotd Dimensions (WxDxH) 3,6 x 2,2 x 8,5 m permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, hydraulic drawing cushion in table and ram, cutting impact cushioning, ram interlocking Foundation depth approx. 3,0 m as is where is, stored in dismantled condition

Condition: used, Year of construction: 1993, pressure 500 t distance between columns 2240 mm stroke 1180 mm distance table/ram, max. stroke up, adjustment up 1800 mm table surface area 2050 x 1800 mm pressure of drawing cushion in table 250 t stroke of drawing cushion in table 380 mm drawing cushion surface in table 1800 x 1200 mm pressure of drawing cushion in ram 122 t stroke of drawing cushion in ram 200 mm drawing cushion area in ram 1800 x 1200 mm ram surface 2215 x 1800 mm table height over floor 500 mm speed down 400 mm/s Iodpfx Abjvuk I Necjtd speed up 10 - 400 mm/s working speed 10 - 100 mm/s depth of the foundation 3,0 m power requirement 122 + 75 + 64,5 kW weight 110,0 t Dimensions (WxDxH) 3,6 x 2,2 x 8,5 m height over floor 6,8 m permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, hydraulic drawing cushion in table and ram, cutting impact cushioning, ram interlocking Foundation depth approx. 3,0 m press is currently under revision with control Siemens S 7 / safety control Pilz a sister machine can be offered in as is where is condition, partially disassembled

Condition: used, Year of construction: 1993, pressure 315 t distance between columns 1660 mm stroke 400 mm Distance table/ram, stroke up 600 mm Table surface area 1600 x 1000 mm table height over floor 960 mm Die cushion pressure in table 80 t Die cushion stroke in table 200 mm Die cushion area in table 950 x 650 mm Side window 720 mm Ram surface 1600 x 1000 mm Oil volume 1400 l Power capacity 57,0 kW Weight 30,0 t Dimensions (WxDxH) 3,0 x 2,9 x 4,4 m permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, hydraulic drawing cushion in table can be offered without putting into operation or alternatively with new control Siemens S 7-1500 F Itodpfxjvuuhme Abcod

Condition: used, Year of construction: 1993, pressure 315 t distance between columns 2350 mm distance table/ram, max. stroke up, adjustment up 1200 mm distance between cutting impact cushioning 1600 mm Distance table/ram, stroke up 1200 mm stroke 800 mm table surface area 2060 x 1260 mm table height over floor 750 mm Die cushion pressure in table 100 t Die cushion stroke in table 400 mm die cushion area 1250 x 1000 mm side window 780 mm ram surface 2200 x 1500 mm Capacity of ejector in ram 63 t speed down 500 mm/s speed up 310 / 410 mm/s working speed 20 - 73 mm/s Itedpfx Abovuugvocod quantity of oil 3900 l power requirement 80,0 + 45,0 kW weight 55,0 t Dimensions (WxDxH) 4,6 x 2,7 x 7,2 m Height above floor 6,0 m Height below floor 1,2 m permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, hydraulic drawing cushion in table, hydraulic ejector in ram, hydraulic cutting impact cushioning, hydraulic ram interlocking can be offered without putting into operation (partly dismantled, in need of overhaul) or alternatively with overhaul and new control Siemens S 7-1500 F