Used Notching for sale (364)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Hsdpeh U Rzgefx Aa Sjff Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: good (used), functionality: fully functional, 1st station: deburring of sheet metal edges, 2nd station: deburring of notches and outer radii, with VA brushes; maximum sheet thickness: 5 mm Hfjdpfjyyahbex Aa Sef

Condition: new, Year of construction: 2026, neu 2026 090194 Mai 2026, Zwischenverkauf Spanien 22400 € 430.08 € 1 60 to 250 mm 5 40 x 11 mm 32 1/min 350 x 15 mm 120 x 10 mm 45 / 40 mm 10 mm max. 150x10 mm 5.5 kW 1850 mm 1300 mm 2100 mm 1390 kg with bending station 5 working stations flat steel shear with device to reduce deformation angle iron shear with round- and squarebars opening triangle notcher Hfedpewirnxefx Aa Sjf punching station press brake device for flat steel table at flat steel station table at notching station length stop 1000 mm with contact switch, for angle, flat or bar station hydraulic drive 2 foot release user manual in GERMAN and ENGLISH WE HAVE MORE THAN 700 REFERENCES!

Condition: new, Year of construction: 2026, neu 2026 090195 Mai 2026, Zwischenverkauf Spanien 15800 € 303.36 € 1 50 to 177 mm 5 1 31 x 12 mm 34 1/min 350 x 15 mm 80 x 8 mm 35 / 30 mm 10 mm 100 x 10 mm 3 kW 1300 mm 1100 mm 1850 mm Hsdpowirahofx Aa Ssff 950 kg with bending station capacity 50 to 5 working stations flat steel shear with device to reduce deformation 350 x 10 mm with adjustment 2° 350 x 15 mm with adjustment 5° angle iron shear 80 x 8 mm with round- and squarebars opening 35/30 mm recangular notcher 90 x 42 x 10 mm punching station 31 x 12 mm press brake device for flat steel max. 100 x 10 mm table at flat steel station table at notching station manual backgauge with electric contact 2 dies V40 and V70 gap at punching station 177 mm vertical movement of all stations (nor radial) hydraulic drive 1 foot release user manual in GERMAN and ENGLISH WE HAVE MORE THAN 700 REFERENCES!

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 49600 € 947.36 € 130 to 600 mm 5 2 50x18 mm 80 mm 600x18 (max. 600x20 mit D mm 120x120x11 (max. 150x150x mm 45/40 mm 130x12 mm 250x12 mm Hfjdpfjynnggjx Aa Ssf 15 kW hydraulic drive 2 foot pedals for independant working on punching and section station bending unit with 2 dies, V50 and V90 flat steel stationWITH DEVICE FOR REDUCING DEFORMATION angle iron station with round and square bar cutting triangular notching station with table and gauge punching station with table and gauge gauge 1000 mm with contact switch, for angle / flat steel station operating manual in German and Englisch

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 35600 € 679.96 € 110 to 610 mm 5 40/20 bzw. 28/28 mm 80 mm 28 1/min 600x15 / 400x20 mm 152x152x13 mm 50 mm 13x52x90 mm 9 kW 2690 mm 1400 mm Hfedpfsynmrbex Aa Ssf 2200 mm 3300 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH OPTION: Kit € 970,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 72800 € 1375.92 € 165 to 610 mm 5 40/30 bzw. 34/34 mm 110 mm 31 1/min 750x20 / 400x30 mm 205x205x18 mm 60 mm 16x58x110 mm 15 kW 2950 mm 1600 mm 2200 mm 6300 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH (sample photos) OPTION "KIT" € 970,-- length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm Hjdpoynmq Refx Aa Soff Further available models of HYD 165 series: model S € 55.200,-- as model SD but 510 mm gap weight 5.200 kg (sample photos) WE HAVE MORE THAN 700 REFERENCES!

Condition: used, Year of manufacture: N/A Condition: excellent Technical specifications: - maximum format -1500 × 1050 mm - maximum speed 14 cycles/min - electromagnetic clutch - self-centering frame for quick clamping of the die - automatic centralized lubrication Device description: ML 1500 is a robust punching and notch press with working area 1500 × 1050 mm, intended for precise punching and creasing operations. The machine construction ensures high stability, long service life and reliable operation even in demanding production environments. Key features: - Standard operating speed of approximately 14 cycles per minute Hfodpfx Ajyk Eg Aea Sjf - Powerful motor in the range of 5.5 – 11 kW (depending on configuration) - High machine weight and rigid frame for accurate cutting results - Suitable for continuous industrial operation - Typical applications: The machine is primarily intended for the printing, packaging, and converting industries, including: - Production of cardboard boxes and packaging, - Die cutting of paper, carton, and similar materials, - Creasing and preparation of folding lines, - Both short-run and high-volume production.

Condition: used, Year of construction: 2023, Manufacturer: SCHMITZ First registration: October 2023 Dimensions: 13,520 x 2,480 x 2,700 mm Gross vehicle weight (GVW): 36,000 kg Unladen weight: 7,880 kg Fifth wheel load: 12,000 kg Hedpjyyz Ivefx Aa Soff Air suspension (lifting/lowering) Disc brakes ABS Mileage: 39,000 km Axle: Schmitz Rotos 430 mm Lift axle Screen-printed floor Side doors Toolbox Body paint: White Chassis paint: Galvanized Tyres: 6 Tyre condition: 70% Rear tyres: 385/65 R 22.5 Interior height: 2,700 mm / Height at sectional door: 2,500 mm 15 + 2 front 7-pin sockets LASI 12642 XL GRP side walls with notched panels / Textile lining Double deck 33/66 with 22 cross beams Sectional door, light 25 mm insulation FP 30 roof LED interior lighting left and right Lift axle As new, only 39,000 km

Year of construction: 2021, condition: used, Year: machine 2021 Condition: Excellent (aș new) Perfectbinder KM41 SC/HC Configuration: - non/Stop production - book block feeder - jogging station with adjustable intensity - milling and notching station with separate drives and speed adjustable - integrated endsheet feeder - endsheet side gluing with Robatech hotmelt nozzles - endsheet position adjustable to the book spine - spinegluing with Hotmelt roller glue unit and Robatech hotmelt premelter - spinegluing with Coldglue unit with pump and level control - backlining station - nipping and pressing station - pile cover feeder with 4 scorring rails - cover and lining side gluing with RobatechHotmelt nozzles - delivery with lay down unit Binding options: HOTMELT adhesive or white dispersion adhesive Hjdpoitycqjfx Aa Sjff Specificacion: - paper size max. 390mm x 300mm x 60mm, min. 140mm x 100mm x 3mm - speed: up to 40 cycles / minute - dimension: Length 6400 mm Width 2150 mm Height 1600 mm - power consumption:9 KW 230/400V 3N, PE, 50 Hz - compressed air:1800 NL/h - 6 bar

Condition: good (used), Year of construction: 1994, Chalet notching machine with 10-meter Tiger stop pusher, equipped with: 1 horizontal milling unit on top, 1 horizontal milling unit below, 1 front/rear milling unit, 1 horizontal drilling unit diameter 16 mm, 1 automatic Tiger stop of 10 meters, year: 2001, effective working length: 9.20 m. Hfodpfx Aaoxbn N To Sef

Condition: good (used), functionality: fully functional, For sale: Used Haco Kingsland Compact 60 – a robust and versatile combination machine for metalworking. This machine combines several functions such as punching, shearing, bending, and notching in a single compact unit, featuring a stable construction and user-friendly operation. Details: Manufacturer: Haco Kingsland Model: Compact 60 Condition: used, fully functional Space-saving, high-performance combination unit Inspection and test run possible by appointment. If interested, feel free to contact us! Hfodpfx Aoyxbyija Ssf

Year of construction: 2000, condition: ready for operation (used), number of axes: 3, This 3-axis Salvagnini P4-2512 was manufactured in 2000, featuring a max bending length of 2500mm and handling sheet thicknesses up to 3.00mm. It includes quick-clamping segments for enhanced flexibility and precision in sheet metal operations. If you are looking to get high-quality bending capabilities, consider the Salvagnini P4-2512 machine we have for sale. Contact us for more information about this machine. Additional equipment • O+UC1000/2(SO) • P40FFICE • Tool set consisting of 13 CLA tool pairs for a total length of 1100 mm • Includes pairs of CLA tools ranging from 25 mm to 90 mm • Quick-clamping segments for large-area recesses Machine Benefits Technical Machine Benefits • Max length of the notched blank at the inlet: 2700 mm • Max width of the notched blank at the inlet: 1500 mm Hfodsx Nr Tzjpfx Aa Sof • Max rotating diagonal of the notched blank: 2700 mm • Max space for bends above the work table: 127 mm • Max sheet thickness at tensile strength 410 n/mm²: 2. 00 mm • Max sheet thickness at tensile strength 600 n/mm²: 1. 25 mm • Max sheet thickness at tensile strength 265 n/mm²: 3. 00 mm • Min sheet thickness: 0. 50 mm Extra Information Optional: set of clamps 84x 25 mm segments 10x 155-200 mm center segments 2x BLC swivel segments 2x BLX sliding segments 2x tool slides Optional: special clamps with recesses: 12x 150 mm quick-release segments 2x 40 mm quick-release segments 20x 50 mm quick-release segments 2x 75 mm quick-release segments 2x 185 x 195 mm center segments Technical Specification Bending Length 2500 mm

Condition: new, Year of construction: 2023, functionality: fully functional, working width: 1,500 mm, feed rate X-axis: 4 m/min, type of input current: three-phase, sheet thickness (max.): 102 mm, total length: 2,300 mm, total width: 2,600 mm, total height: 2,500 mm, overall weight: 4,000 kg, working height: 950 mm, workpiece length (max.): 102 mm, Deburring on both sides in just one pass - of course with 100% reproducible results and precise processing of the inside and outside edges - only the EdgeRacer 1500 D offers you this. The double-sided deburring EdgeRacer 1500 D is the right choice for precise double-sided deburring and edge rounding. In addition to flat sheets, it can also process sheets with beads, notches, thread pull-throughs and the like. The maximum component height is 102 mm. The infeed of the brushes working from above and below can be set independently of each other. Thanks to the roller conveyor, the infeed can also be below or above roller table level. Hedpfsucw Rbox Aa Soff

Condition: used, Year of construction: 2007, Technical details: throat: 640 mm round bar steel: stanzen: Ø 26 x 20 mm Punching capacity: 70 t total power requirement: 5,5 kW weight of the machine ca.: 2,0 t dimension machine xH: 2,0 x 1,0 x 1,8 m hydraulic section steel shearing machine shearing station: -shear max. 300 x 20mm / 375 x 15mm -shear cutting max. 150 x 13mm -holding-down device adjustable in length to 630mm profile station: processing of round and square profiles; U-profiles; double T-beams and non-symmetrical angles Angle/profile cutting -angle steel max. 90° shearing = 150 x 15mm and 45° shearing = 80 x 10mm -U-I profile = 130 x 65mm; T profile = 90 x 12mm -profile cutting max: round steel Ø 45mm and square steel 45mm -knife cutting edges fourfold Punching station: -Punching force 60to -throat 640mm -table WxD = 1000 x 600mm -punching max. Ø x thickness: Ø 26 x 20mm and Ø 57 x 9mm -slot punching D x W x D: 10 x 45 x 90mm -through hole in table Ø 40mm -Equipment: stop bar Al angle 100 x 80 x 1000mm Notching station: -Table W x D 430 x 380mm -notches: material thickness 10mm; width 45mm; depth 60 - 90mm; angle flange 100 x 10mm Punching: -Table 600 x 600mm -throat 625mm -bore max: Ø 57 x 12mm -working stroke 80mm; stroke rate 34 strokes/min; punching pressure 40to -stop angle 200 x 100mm L=600mm Notching station: -Table size 450 x 450mm -notching material thickness 13mm; width 52mm; depth V 90° 70 - 100mm; angle flange 100 x 13mm Please ask for accessories. Operation by foot switch Some accessories available. Please ask. Hedpfsu Icmhsx Aa Ssff *

Condition: used, Year of construction: 2003, Technical details: throat: 625 mm number of strokes: 34 Hub/min Punching capacity: 95 t stroke: 80 mm flat steel: 480 x 15 / 380 x 20 mm U-H profile: 160 x 90 Hfjdpou Icl Rofx Aa Ssf knife length: 483 mm total power requirement: 7,5 kW weight of the machine ca.: 2,7 t dimension machine xH: 1,4 x 0,8 x 1,8 m hydraulische section steel shear shearing station: -shearing max. 380 x 20mm / 480 x 15mm -shear cutting max. 120 x 15mm -holder adjustable in length to 750mm -knife cutting edges = upper knife 2-fold and lower knife 4-fold profile station: processing of round and square profiles; U-profiles; double T-beams and unequal angles -angle shearing max. 90° shearing = 150 x 15mm and 45° shearing = 80 x 10mm -Profile cutting max. round steel = Ø 50mm; U-H profile = 160 x 90mm; T-profile = 120 x 12mm. Punching: -Table 600 x 600mm -throat 625mm -bore max: Ø 57 x 12mm -working stroke 80mm; stroke rate 34 strokes/min; punching pressure 40to -stop angle 200 x 100mm L=600mm Notching station: -Table size 450 x 450mm -notching material thickness 13mm; width 52mm; depth V 90° 70 - 100mm; angle flange 100 x 13mm Operation by foot switch Some accessories available. *

Condition: excellent (used), Year of construction: 2017, machine/vehicle number: 302.11.009.17, functionality: fully functional, operating hours: 2,322 h, power: 12 kW (16.32 HP), travel distance X-axis: 3,005 mm, travel distance Y-axis: 1,550 mm, travel distance Z-axis: 250 mm, number of axes: 5, number of slots in tool magazine: 18, actuation type: electric, total height: 2,400 mm, total length: 8,000 mm, total width: 2,500 mm, overall weight: 5,000 kg, We are offering this used Format-4 profit H350 through-feed machining center, year of manufacture 2017. CNC 5-Axis Machining Center • Manufacturer: FORMAT 4 • Model: H350 16.30 • Year: 2017 • Machine with premium configuration • Cardanic 5-axis electrospindle: 12 kW • Machine software: WOODFLASH • 18-position disc tool changer, traversing in X (H350L) • Pickup station for sawblade, traversing in X for a 350 mm blade • 9-position linear tool changer incl. tool length measuring unit • 5-color optical status indicator • Blue LED light strip, short • Safety system with foot mats, incl. pendulum mode • Automatic central lubrication • Portal drive on both sides • Large drilling head DH 24 6H 1S • Controlled central extraction connection • 6 workpiece supports with front and rear stop rows • Position display of workpiece supports and vacuum cups via laser • One vacuum connection for template milling work • Vacuum system 90 m³/h • Left-side safety fence on the machine • Enclosed cable drag chains on X and Y axes • Controlled compressed air connection for frame clamps • Vacuum and compressed air release for 6 workpiece supports • Right-side safety fence on the machine • Mobile operator terminal (instead of fixed terminal) • Lamello Clamex P Macro AB WD FLASH • F4 notching macro • 5-axis interpolation enabled • Cabinet generator design software (drawing software) • Console release with control voltage included • Includes 8 vacuum cups • Travel paths: - X: 3005 mm - Y: 1550 mm - Z: 250 mm Hjdpfsyw Nciex Aa Soff • Machine in absolutely top condition with very low operating hours • Available immediately from March 2026 • Overall dimensions: approx. 8000 x 2500 x 2400 mm • Total weight: approx. 5000 kg - Handle for console broken and glued, see photo! - Emergency stop switch on hand control defective! Can be replaced with a spare part for approx. €100!! Frame clamps for this machine, see photo. Additional price: €2,000!! Frame clamps are installed for this machine and set up with a work station, so machining can be performed on both sides. Sale is with VAT duly shown on invoice! Machine available immediately! Machine can be inspected on site. Machine will be dismantled in 2 weeks!! Loading can be organized at extra cost. If you have any questions or need further information, please feel free to send us a message or call us.

Condition: ready for operation (used), functionality: fully functional, control type: manual, actuation type: hydraulic, Geka (Spain) Hydraulic Punching, Shearing, and Notching Machine Model: Hydracrop–55/110A Year of Manufacture: 2001 Flat Bar Shear Capacity: 300 x 15 mm / 200 x 20 mm Blade Length: 305 mm Square: 25 mm Working Height: 880 mm Angle Shear Capacity: 1100 kN Deformation-free Angle Iron: 120 x 120 x 10 mm Angle Iron 45° Shear: 70 x 70 x 7 mm Round and Square Bar Shear Round Steel: 40 mm Square Steel: 40 mm Notcher Sheet Thickness: 10 mm Angle Iron: 100 mm Notch Depth: 90 mm Notch Width: 42 mm Punching Station Capacity: 550 kN Maximum capacity with quick-change system: Ø 40 x 10 mm / Ø 20 x 20 mm Throat Depth: 250 mm Stroke Length: 60 mm Working Height: 1085 mm General Specifications Number of strokes per minute at 20 mm stroke: 25 Power: 3 kW Net weight: 1320 kg Gross weight: 1518 kg Dimensions (L x W x H): 1600 x 1100 x 2000 mm Machine Details - 2 cylinders: one for the punching side, one for the shearing side - Punching unit with quick-change system - C-frame die holder + extra support - Nipple and die up to Ø 40 mm selectable - Flat bar shear incl. support table and 45° and 90° guides - Angle shear - Round and square bar shear (suitable for mounting U and I profiles as well) - Rectangular notcher - Emergency stop - Key switch for notcher safety - Selector switch for deep or shallow punch/shear operation - Selector switch for foot pedal / back gauge - Stroke adjustment for punch and shear side - 2 foot pedals - Scrap collection tray for punch slugs - Dutch instruction manual Includes: Punch table incl. back stops Notching table incl. back stops Electric length stop 1000 mm 30 sets of punch nipples Price of the Geka Hydraulic Punch/Shear/Notch Machine: €16,500 Machine is as new, original paint, like new, original finish Delivery conditions: Delivery time: from stock, subject to prior sale Delivery: ex works Baarle-Nassau Payment: before collection Prices: net, excluding VAT Machinehandel De Leeuw BV cannot be held liable for discrepancies between the technical specifications in this offer and the actual machine, accessories, and/or parts. Machines, accessories, and parts are sold as-is and as known to the buyer. We cannot provide a warranty for used machines, accessories, and parts. Delivery terms: Delivery time: ex stock, excluding VAT Delivery: ex works Baarle-Nassau Payment: before collection Prices: net, excluding VAT Machinehandel De Leeuw BV is one of the few companies in Europe that stocks and sells primarily used Kardex Remstar automatic lift and rotating warehouse systems. We install and/or dismantle these systems safely with VCA-certified engineers and have been doing so for more than 33 years. Best regards, Antoine de Leeuw Machinehandel De Leeuw BV Oordeelsestraat 7-B Hsdpsyxpawefx Aa Sjff 5111 PA Baarle-Nassau The Netherlands VAT No.: NL800103026B01 Chamber of Commerce Tilburg 18034279

Year of construction: 2012, operating hours: 3,496 h, condition: excellent (used), functionality: fully functional, Quadra L1 in excellent condition with extremely low operating hours for sale. Available with enclosure upon request! On-site demonstration with profile possible. Quadra L1 pass-through machining center with premium configuration: - 6 spindles, 360° rotatable to machine profiles at any angle - 7.5 meter bar loading magazine - 600mm saw and notching unit - Profile positioning system - MG Pilot handheld controller - 2 steel front conveyors for scrap removal - Slice software - CamPlus / Job software Installation, commissioning, and training can also be provided by us! CNC 12-axis machining center, designed for milling, drilling, and cutting operations on aluminum and light alloys. The QUADRA L1 consists of an automatic tool magazine and a pusher feed system for profiles up to 7500 mm, complete with profile clamping gripper. As the collet moves, the feeder returns to its starting position, allowing the loader to prepare the next profile simultaneously. The central section houses the milling and cutting modules. The CNC 4-axis milling module is equipped with 4 to 6 electrospindles, enabling complete contour machining of the workpiece in any orientation. The CNC 3-axis cutting module features a Ø 600 mm blade with a plunging movement. The QUADRA L1 also includes an automatic outfeed system from the cutting unit to the unloading magazine. The system is equipped with a magazine with cross belts for unloading finished workpieces up to 4000 mm (7500 mm optional). The machining unit can be fitted with an optionally available enclosure, providing sound insulation for the central operational area, which not only protects the operator but also reduces noise emissions. Hfodpfx Aajywpcvs Sef Machine demonstration available!

Condition: excellent (used), functionality: fully functional, Rainer bevelling machine, model 250/6, with fixed angle, max thickness 6 mm, used machine, internal code: SVR 401 Hodpfxjyv Hyie Aa Sjff

Condition: excellent (used), functionality: fully functional, sheet thickness (max.): 6 mm, BEVELING MACHINE FIM - VERSA MODEL 206 WITH VARIABLE ANGLE THICKNESS: 6 mm Hodpfxeyv Hwho Aa Sjff USED MACHINE INTERNAL CODE: SVR 400

Year of construction: 2000, condition: ready for operation (used), Various smaller workshop metalworking machines from various manufacturers are available. 1) Brush machine RSA STL, year of manufacture: 1979. 2) Belt grinder Flott BSM 75. 3) Pull saw Graule ZS 85, year of manufacture: 1994. 4) Belt grinder Ludwig Gartner AZ2N. 5) Band saw Raim 360, year of manufacture: 1995. 6) Column drilling machine Quantum B 30 GS, year of manufacture: 2005. 7) Belt grinding machine HM TAS 75, year of manufacture: 2000. 8) Assembly band saw Berg & Schmid PBS 148. 9) Pull saw Graule ZS 200 N-S, year of manufacture: 2015. 10) Aluminum circular saw MEP Cobra 350 MA. 11) Notching saw Graule AS 450-D, year of manufacture: 2003. 12) Corner crimping press Rapid HP-205, year of manufacture: 1995. 13) Hydraulic press Schüco. 14) Notching saw Graule AS 450, year of manufacture: 2000. 15) Tie bar punching machine Schüco LA 10, year of manufacture: 2020. An on-site inspection is possible. A package sale of all items is preferred. Hodpfx Aeyu T Ehoa Seff

Condition: used, NC Multi-Blade - Double-Blade Saw for Light Metal MIKSITZ Year of manufacture: 1991 Circular saw, aluminium circular saw, table circular saw, mitre saw For cross-cutting and notching aluminium profiles Saw blade travel: 500 mm Max. cutting height: 100 mm Saw blade speed: approx. 5000 rpm Installed saw blade diameter: 300 mm Max. saw blade diameter: 400 mm Motor power: 5.5 kW Power supply: 400 Volt, 50 Hz Table size: 1100 x 1100 mm Table opening: 300 x 1100 mm Working height: approx. 1100 mm Tool holder: SK40 - Several saw blades can be mounted on a single work shaft with double-sided bearing - A long SK40 arbor serves as the work shaft - Belt drive between the drive motor and saw shaft - Table height adjustable via hand crank (to set cutting depth) - Fixtures and stops can be mounted on the table Hjdpfx Aodzp Snea Seff - Saw blade movement via ball screw spindle with servomotor - Single-axis NC control for the cutting movement, LENORD + BAUER type GEL 7541.0000 - Separate control cabinet Space requirement (L x W x H): 1800 x 1600 x 1700 mm Weight: approx. 1100 kg

Condition: excellent (used), functionality: fully functional, Year of construction: 2002, control type: manual, degree of automation: semi-automatic, controller manufacturer: GEKA, stroke rate (min.): 37 1/min, stroke adjustment: 60 mm, throat depth: 500 mm, punching force: 55 t, punching diameter: 100 mm, cutting range flat at 45° (X-axis): 300 mm, working height: 1,085 mm, oil tank capacity: 80 l, overall weight: 1,750 kg, total length: 2,100 mm, total width: 1,160 mm, total height: 2,090 mm, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, emergency stop, foot remote control, notching unit, GEKA HYDRACROP 55 SD – Universal Ironworker | 360° | Ø100 mm Bending Station For sale: professional dual-cylinder universal ironworker from the renowned Spanish manufacturer GEKA, model Hydracrop 55 SD. The machine is in excellent technical condition, ready for immediate operation in demanding industrial environments. WHAT SETS THIS UNIT APART? Full 360° Mobility: The machine is mounted on a special rotary bearing, enabling complete 360-degree rotation. This feature is invaluable for processing long flat bars or profiles in smaller workshops. SD Version (Extended): The throat depth is an impressive 500 mm, allowing work with very wide sheet metal panels. Extreme Punching: The machine is equipped with an attachment for punching holes up to Ø100 mm. Additional Bending Station: Includes a professional flat bar bending station, making this machine a versatile metalworking center. TECHNICAL DATA: - Punching force: 55 tons (550 kN) Hodpfx Aajyricds Soff - Number of cylinders: 2 (enabling operation by two users at different stations simultaneously) - Number of workstations: 5 (punching, angle shearing, flat bar shearing, round/square bar shearing, notching) - Max. sheet thickness: 20 mm - Angle cutting at 90°: 120 x 120 x 10 mm - Motor power: 5 kW - Stroke rate: 37/min - Weight: approx. 1,750 kg EQUIPMENT & BENEFITS: - Control system: Intuitive foot pedal control with “Touch & Cut” function (electric back gauge) - Safety: Emergency stop, full CE marking, and complete technical documentation (DTR) - Condition: Well-maintained machine, regularly serviced, with all measurements and operating parameters perfect.

Condition: used, Year of construction: 2025, working width: 6 mm, Equipment: lighting, OPTIMER XL6000 / 47M notched disc / 1 set double-U roller OPT.L/XL6000 / 1 set without front tools / 1 set leveling harrow in front of packer OP XL6000 / 1 set front support wheels / 1 Hedpjyahgqsfx Aa Soff