Used Operating Instructions for sale (26,695)

Condition: new, Deburring machine Make: Assfalg Model: FS 5 Condition: new machine Speed: 2,800 rpm Max. chamfer width: 3 mm Equipped as standard with: - Guide rail 400 x 50 x 10 mm - Cutter head without indexable inserts - Chip drawer - Operating instructions Ihodpfxeb E Dc Hs Abcow

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control Iodpfx Absk S Dt Tjcohw - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: new, functionality: fully functional, Year of construction: 2025, pipe diameter (max.): 51 mm, bending angle (max.): 190 °, bending radius (max.): 220 mm, power: 11.5 kW (15.64 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, warranty duration: 24 months, drive type: Inverter, operating speed: 38 mm/s, pressure: 150 bar, wall thickness: 3 mm, working length: 3,000 mm, Equipment: documentation/manual, 51x3mm NC Type Tube Bending Machine The “Atlas” tube bending machines are nc structures. This type of tube benders includes hydraulic and pneumatic for all clamping and pushing operations. Atlas has 3 different type which are NB, NBR, NBRF. NB series makes bending operation automatically. NBR series makes bending and rotating operation automatically. NBRF series makes bending, rotating and feeding operation automatically. A.C servo engine control gives semi automatic bending capability for NBR and NBRF series. With ergonomic loading height, machine is accordance with health and safety instructions and can avoid the ergonomy problems. Improvable program setup settings for optimizing the results of your bending projects, program setup settings that can be developed. With energy saving mode, your energy efficiency will be increased, the nature and our future can be protected. Inverter control system, a new generation of precision bending system, can help to optimally actualize your bending project. Iodpfx Aovwg Evjbcohw Powerbend mode will help the bending process of your difficult bending materials. User-friendly, easy and quick to learn interface which allows you to quickly start the new projects. Easy to use with min 7-inch touch screen HMI. Fast and accurate bending with minimal friction with the help of Linear Guide. Flexible bending ability with the help of rotation of bending head. Bending precision will be top level with the help of Non-Vibrating structure. Easy to understand and solve the problems with the help of end user error messages, it will help to keep your business on running. Quality bending with wiper, ball mandrel and other systems.

Condition: new, functionality: fully functional, Year of construction: 2025, pipe diameter (max.): 76 mm, bending angle (max.): 190 °, bending radius (max.): 250 mm, power: 27 kW (36.71 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, warranty duration: 24 months, drive type: Inverter, operating speed: 38 mm/s, pressure: 150 bar, wall thickness: 4 mm, working length: 3,000 mm, Equipment: documentation/manual, 76x4mm Semi Automatic NC Tube Bending Machine The “Atlas” tube bending machines are nc structures. This type of tube benders includes hydraulic and pneumatic for all clamping and pushing operations. Atlas has 3 different type which are NB, NBR, NBRF. Iodpfx Asvwg D Sobcjhw NB series makes bending operation automatically. NBR series makes bending and rotating operation automatically. NBRF series makes bending, rotating and feeding operation automatically. A.C servo engine control gives semi automatic bending capability for NBR and NBRF series. With ergonomic loading height, machine is accordance with health and safety instructions and can avoid the ergonomy problems. Improvable program setup settings for optimizing the results of your bending projects, program setup settings that can be developed. With energy saving mode, your energy efficiency will be increased, the nature and our future can be protected. Inverter control system, a new generation of precision bending system, can help to optimally actualize your bending project. Powerbend mode will help the bending process of your difficult bending materials. User-friendly, easy and quick to learn interface which allows you to quickly start the new projects. Easy to use with min 7-inch touch screen HMI. Fast and accurate bending with minimal friction with the help of Linear Guide. Flexible bending ability with the help of rotation of bending head. Bending precision will be top level with the help of Non-Vibrating structure. Easy to understand and solve the problems with the help of end user error messages, it will help to keep your business on running. Quality bending with wiper, ball mandrel and other systems.

Condition: new, functionality: fully functional, Year of construction: 2025, pipe diameter (max.): 32 mm, bending angle (max.): 190 °, bending radius (max.): 200 mm, power: 9 kW (12.24 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, warranty duration: 24 months, drive type: Inverter, operating speed: 99 mm/s, pressure: 130 bar, wall thickness: 2 mm, working length: 1,920 mm, Equipment: documentation/manual, 32x2mm Semi Automatic NC Tube Bending Machine The “Atlas” tube bending machines are nc structures. This type of tube benders includes hydraulic and pneumatic for all clamping and pushing operations. Atlas has 3 different type which are B, BR, BRF. B series makes bending operation automatically. BR series makes bending and rotating operation automatically. BRF series makes bending, rotating and feeding operation automatically. A.C servo engine control gives semi automatic bending capability for BR and BRF series. With ergonomic loading height, machine is accordance with health and safety instructions and can avoid the ergonomy problems. Improvable program setup settings for optimizing the results of your bending projects, program setup settings that can be developed. With energy saving mode, your energy efficiency will be increased, the nature and our future can be protected. Inverter control system, a new generation of precision bending system, can help to optimally actualize your bending project. Powerbend mode will help the bending process of your difficult bending materials. User-friendly, easy and quick to learn interface which allows you to quickly start the new projects. Easy to use with min 7-inch touch screen HMI. Fast and accurate bending with minimal friction with the help of Linear Guide. Flexible bending ability with the help of rotation of bending head. Bending precision will be top level with the help of Non-Vibrating structure. Ihjdpfx Absvx D D Secow Easy to understand and solve the problems with the help of end user error messages, it will help to keep your business on running. Quality bending with wiper, ball mandrel and other systems.

Condition: new, functionality: fully functional, Year of construction: 2025, pipe diameter (max.): 32 mm, bending angle (max.): 190 °, bending radius (max.): 220 mm, power: 8.2 kW (11.15 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, warranty duration: 24 months, drive type: Servo - Hydraulic, operating speed: 99 mm/s, pressure: 150 bar, wall thickness: 2 mm, working length: 2,500 mm, Equipment: documentation/manual, 32x2mm Fully Automatic Tube Bending Machine The “Atlas” tube bending machines are nc structures. This type of tube benders includes hydraulic and pneumatic for all clamping and pushing operations. Atlas has 3 different type which are NB, NBR, NBRF. NB series makes bending operation automatically. NBR series makes bending and rotating operation automatically. Iedpfsvwg Hmox Abcohw NBRF series makes bending, rotating and feeding operation automatically. A.C servo engine control gives semi automatic bending capability for NBR and NBRF series. With ergonomic loading height, machine is accordance with health and safety instructions and can avoid the ergonomy problems. Improvable program setup settings for optimizing the results of your bending projects, program setup settings that can be developed. With energy saving mode, your energy efficiency will be increased, the nature and our future can be protected. Inverter control system, a new generation of precision bending system, can help to optimally actualize your bending project. Powerbend mode will help the bending process of your difficult bending materials. User-friendly, easy and quick to learn interface which allows you to quickly start the new projects. Easy to use with min 10-inch touch screen HMI. Fast and accurate bending with minimal friction with the help of Linear Guide. Flexible bending ability with the help of rotation of bending head. Bending precision will be top level with the help of Non-Vibrating structure. Easy to understand and solve the problems with the help of end user error messages, it will help to keep your business on running. Quality bending with wiper, ball mandrel and other systems.

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, operating hours: 4,854 h, load capacity: 4,500 kg, lifting height: 4,900 mm, free lift: 1,550 mm, load center: 600 mm, fuel type: diesel, mast type: triplex, construction height: 2,400 mm, motor manufacturer: DEUTZ, gearing type: hydrostat, fork carriage width: 1,320 mm, fork length: 1,200 mm, fork width: 150 mm, fork thickness: 50 mm, tire condition: 100 %, front tire type: superelastic tires (black), front tire size: 200/50-10, rear tire type: superelastic tires (black), rear tire size: 355/45-15, overall weight: 11,000 kg, empty load weight: 6,500 kg, total height: 2,400 mm, total length: 2,300 mm, total width: 2,250 mm, color: green, motor model: 2,9LH, Equipment: CE marking, all wheel drive, cabin, lighting, pallet forks, sideshift, -- 🚜 USED FORKLIFTS WITH QUALITY GUARANTEE – FT LOGISTICS -- 🏆 Years of experience | 🛠️ In-house service & paint shop | 💡 Professional consultancy | 🚛 Own fleet for transport | 🤝 After-sales support ❓ Searching for a forklift you can truly rely on? We are a renowned supplier of new and pre-owned forklifts with years of industry experience. We proudly serve clients across Europe – from small businesses to large industrial enterprises. With us, forklifts are more than just machines – they are your assurance of reliability and efficiency throughout your logistics operations. -- Why choose us? -- ✅ Every forklift undergoes a comprehensive technical inspection (diagnostics, testing, filter & oil change, refurbishment of key components) ✅ UDT (Office of Technical Inspection) approval available on request ✅ Own paint shop and service workshop – forklifts fully optimised both visually and mechanically ✅ Pan-European transport provided by professionally trained drivers ✅ Operator instruction upon delivery + on-site functional demonstration Ihjdpeypxyaefx Abcow ✅ After-sales technical assistance – always at your disposal ✅ Visit us to inspect & test equipment in person – you are welcome! ✅ Hundreds of satisfied customers across Europe – join their ranks today ✅ Financing assistance – partnerships with leading leasing companies ✅ Invoice in EUR or PLN – you choose -- 🔥 AVAILABLE FROM STOCK: COMBILIFT C4500 – Multi-Directional Forklift -- 📅 Year of manufacture: 2020 ⏱️ Operating hours: 4,584 h ⛽ Power unit: Diesel 📦 Load capacity: 4,500 kg 📏 Mast: Triplex – 4,900 mm 🔩 Fork positioner 1,320 mm | Forks 1,200 mm 🛞 Superelastic tyres – 100% condition ⬆️ Free lift: 1,550 mm ⚙️ Technical condition: Excellent – major service just completed ✨ Aesthetic condition: Very well-maintained, rust-free, immediately ready for operation 📐 Dimensions: Height: 2,400 mm Length: 2,300 mm Width: 2,250 mm Fork positioner width: 1,320 mm Overall height: 2,400 mm -- Ideal for: 🏭 Warehouses with narrow aisle widths 🌲 Wood, steel, and pipe industries 📦 Handling long or bulky loads 🏢 Suitable for both indoor & outdoor applications 🚀 FT Logistics – Quality you can rely on. Service you can trust.

Condition: new, Year of construction: 2026, functionality: fully functional, power: 5.5 kW (7.48 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, grinding belt width: 150 mm, grinding belt length: 9,000 mm, height adjustment type: electric, grinding belt speed: 25 mm/s, total height: 2,200 mm, total length: 4,640 mm, total width: 2,650 mm, overall weight: 1,200 kg, grinding length: 2,500 mm, workpiece weight (max.): 80 kg, extraction connection diameter: 180 mm, grinding width: 950 mm, rotational speed (max.): 1,435 rpm, space requirement height: 2,200 mm, space requirement length: 4,640 mm, space requirement width: 2,650 mm, table height adjustment: 500 mm, Equipment: documentation/manual, Long-belt sander M2S92-150 with two sanding belts for manual sanding, matting, and polishing. For processing steel, stainless steel, and brass. Not for aluminum or titanium! Scope of delivery includes: - Machine stand with connecting elements - Belt drive - Pneumatic belt tensioning and manual belt guide - Sanding unit with contact roller, manually movable from belt 1 to belt 2 - Electric table lift - Flat machine table - Workpiece stop on the machine table - Original equipment sanding belts - CE-certified version - Operating instructions + manufacturer's declaration according to Appendix 2 The sturdy machine with its welded steel construction runs very smoothly. The two machine stands are equipped with a crank so that even longer parts can be sanded on the machine. The sanding belt is guided by three belt guide rollers, providing the largest possible working area for the operator and thus ensuring optimal work, especially with hand sanding blocks. The belt is driven by a three-phase motor with a balanced belt drive roller. Each belt has a separately adjustable, pneumatic belt tensioner. This allows for optimal belt tension adjustment for each belt. The dust collection system is designed to effectively capture the resulting sanding dust and direct it to the extraction nozzle when connected to an appropriate extraction system. To ensure effortless operation, the sanding unit is mounted on play-free roller guides. The machine table can be easily and quickly adjusted to the required workpiece height using the electric table lift. The table lift guide elements are maintenance-free. For loading, the table can be extended far enough that workpieces do not have to be pushed under the sanding belt when placed on the table. The electrical controls for the main functions are conveniently located in the center of the machine. Machine color: RAL 9001 cream white and RAL 5003 sapphire blue Control cabinets and small housing in "light gray" The machine is supplied in its basic configuration with two initial equipment belts (W x L) 150 x 9000 mm and a contact roller approximately 50° shore for a belt width of 150 mm. Additional accessories: 3-axis table with integrated handling device for rotating and swiveling the workpieces. The handling device is mounted in the center of the table under the insert frame. To work with the handling device, the insert frame is removed from the machine table. The handling device is equipped with four vacuum suction cups for holding the workpieces and consists of: The bearing with the rotary axis, to which a brake disc is mounted on the rear. The swivel device is attached to the front of the rotary axis. This can be locked at 0°, 22.5°, 45°, 67.5°, and 90°. An additional locking disc is mounted on the swivel head, allowing for fine adjustment of the workpieces to the sanding belt. The rotary and swivel axes are unlocked pneumatically via a foot switch, while the rotary axes are moved manually. Workpiece weight when used as a flat table with an inserted frame = 80 daN. Workpiece weight when using the handling device relative to the clamping plate = 25 daN or 120 Nm relative to the center of the rotary axis. Ihsdpfx Aov S Sr Rjbcjw

Condition: new, Year of construction: 2026, functionality: fully functional, power: 5.5 kW (7.48 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, grinding belt width: 150 mm, grinding belt length: 7,000 mm, height adjustment type: electric, total height: 2,200 mm, total length: 3,550 mm, total width: 2,000 mm, overall weight: 870 kg, grinding length: 1,500 mm, workpiece weight (max.): 80 kg, extraction connection diameter: 180 mm, grinding width: 950 mm, rotational speed (max.): 1,435 rpm, space requirement height: 2,200 mm, space requirement length: 3,550 mm, space requirement width: 2,000 mm, table height adjustment: 500 mm, Equipment: documentation/manual, Long-belt sanding machine MS92-150 3-cornered sanding belt 150x7100 for manual sanding, matting and polishing. For processing steel, stainless steel and brass. The scope of delivery includes - Machine stand with connecting elements - Infinitely variable belt drive - Pneumatic belt tensioning and manual belt tracking regulation - Sanding unit with contact roller - Electric table lift - Flat machine table - Workpiece stop ruler on the machine table - Original equipment sanding belt - Operating instructions + manufacturer's declaration - CE version Ihjdpotwb U Asfx Abcow The stable machine frame in welded steel construction results in very smooth machine operation. The two machine stands are equipped with an offset so that longer parts than the machine table can be sanded. The sanding belt guide via 3 belt deflection rollers results in the largest possible open working area for the operator and therefore good working conditions, especially with hand sanding blocks. The belt is driven by a three-phase motor with a balanced belt drive roller. The belt has adjustable pneumatic belt tension. The dust collection device is dimensioned so that the sanding dust is collected and directed to the extraction nozzle when connected to an appropriate extraction system. The sanding unit is mounted on backlash-free roller guides to ensure effortless operation. The machine table can be easily and quickly adjusted to the correct workpiece height using the electromotive table lift. The table lift guide elements are maintenance-free. For loading, the table can be extended so far that workpieces do not have to be pushed under the sanding belt when loading. The electrical controls for the main functions are arranged in the middle of the machine for ease of use. Machine color: RAL 9001 cream white and RAL 5003 sapphire blue Switch cabinets and small housing in " light gray " The machine is supplied as standard with an original equipment belt (W x L) 150 x 7100 mm and a contact roller approx. 50° Shore for 150 mm belt width. Additional accessories: 3-axis table with integrated handling device for turning and swiveling the workpieces. The handling device is mounted in the center of the table under the insertion frame. To work with the handling device, the insertion frame is removed from the machine table. The handling device is equipped with four vacuum suction cups to hold the workpieces and consists of: The bearing with the rotary axis, on which a brake disk is mounted at the rear. The swivel device is attached to the front of the rotary axis. This can be locked at 0°, 22.5°, 45°, 67.5° and 90°. An additional locking disk is attached to the swivel head, which is used for fine adjustment of the workpieces to the sanding belt. The rotary and swivel axes are unlocked pneumatically using a foot switch, while the rotary axes are moved manually. Workpiece weight when used as a flat table with the insert frame in place = 80 daN Workpiece weight when using the handling device in relation to the clamping plate = 25 daN or 120 Nm in relation to the center of the rotary axis.

Condition: good (used), Year of construction: 2009, functionality: fully functional, Table size: 600 x 400 mm Maximum workpiece size: 900 x 600 x 330 mm Maximum workpiece weight: 750 kg X-axis travel: 400 mm Y-axis travel: 300 mm Z-axis travel: 300 mm Generator output: 60 A Machine dimensions: 2190 x 1880 x 2360 mm Iodpfoyity Ujx Abcehw Machine weight: 2800 kg Accessories: - Magnetic table and EROWA clamping system - Machine manual and operating instructions The machine is in very good condition and comes from a small family business that recently closed down.

Condition: ready for operation (used), hole punhing press: pressure 100 t output 40 in 22 mm L-beam 160 x 16.0 mm square edge steel 50.0 mm round bar steel 50.0 mm flat steel 600 x 15.0 / 400 x 20.0 mm throat 610 mm engine output 8.5 kW weight of the machine ca. 3150 kg range L-W-H ca. 2200 x 1400 x 1830 mm - in checked conditions - machinevideo - ?v=oV49fdNM8dg Equipment: - Robust electro-hydraulic profile steel shear - Punching station with punch quick-change device and die holder - Includes large support table with movable stop - Continuous stroke adjustment with jog/setup mode Ijdjxn Tydepfx Abcjhw - Triangular notching station with support table - Bar, profile, and angle steel shear - Flat steel station with support and guide table - Various punches and dies (drawer cabinet) - 1x electric contact length stop - 2x freely movable foot switches - Operating instructions (PDF)

Condition: used, Year of construction: 2016, TECHNICAL DATA AXES Max. workpiece dimensions X-Y-Z mm 3050 x 800 x 50 Min. workpiece dimensions X-Y-Z mm 300 x 90 x 10 Drilling/slotting working area mm 0 x 800/0 x 800 X axis stroke mm 750 Max. travel speed of X-Y axes m/min 25 DRILLING UNIT Vertical spindles Number 7 (4X-4Y one common) Horizontal spindles (along the Y axis) Number 2 (1+1) Horizontal spindles (along the X axis) Number 1 Fixed grooving saw (direction) X Grooving saw diameter mm 100 Max. grooving saw thickness mm 5 Motor power kW (HP) 1.5 (2) Spindle speed rpm 3350 Grooving saw speed rpm 4300 INSTALLATION Power supply V (Hz) 380 / 400 (50 / 60) Installed power KVA 4.5 Compressed air requirement bar 6 Compressed air consumption Nl/cycle 90 Extraction requirement m3 / h 1200 Extraction air speed m / sec 20 Extraction nozzle diameter mm 80+80 F10L Drilling unit Includes: - 7 independent vertical spindles - Drill chuck D10 mm - Distance between spindles 32 mm - 2 horizontal drilling heads, 1 in X direction with one drill, 1 double drilling head in Y direction (1 + 1 drill chuck D10 mm) - Speed 3350 rpm - 1 integrated sawing unit in X (max. Diameter 100 mm) - Saw blade speed 4300 rpm - Motor power 1.5 kW - Vertical pneumatic travel per spindle 70 mm - Horizontal pneumatic travel of the drilling unit. Positioning of the workpiece and drive of the work unit: A CNC-controlled suction cup clamps the workpiece and positions it sequentially under the work unit during machining. Movement in the X and Y axes takes place on THK guides with transmission to reinforced toothed rails. Movement in the Z axis is pneumatically controlled on ball-bushing guides with adjustable stop positioning. The positioning of the work units is carried out using technology and drives with DC motors. CNC CONTROL The control system was specially developed for use in drilling and milling machines. CN - 7" color screen with touchscreen function - Alphanumeric keyboard - Self-diagnosis and any error messages or malfunctions that may occur, in the operator's language Programming - Programming via the CN - Automatic optimization of drilling operations - Option of plate zero point shift - Option of saving and importing drilling programs via USB dongle - Option of importing drilling programs from CAD-CAM external software Configuration - User interface in the same language as the instruction manual Graphic representation of the unit configuration Vacuum suction cups "B-Power Vacuum suction cups with double vacuum connection, recommended for particularly porous panels (e.g. MDF light). Machine user interface software Xilog Maestro USB Hardware and software requirements: - Operating system: Windows XP Professional (SP2), Windows Vista or Windows 7 - Processor: Intel compatible, 2GHz min; Multicore processor recommended - Memory capacity: 1GB min., recommended 2GB - Free disk space: 5GB - Graphic card: Compatible OpenGL (The code includes a DVD for installation and a USB key) Xilog Maestro Features Programming - Parametric, graphic programming - Assisted programming with graphic and syntax help for drilling operations - Possibility to create and save machining macros Integrated additional functions - Self-diagnosis and possible error messages or malfunctions, in the operator's language - User interface in Ijdpfxjvvi I Re Abcehw

Condition: used, Year of construction: 1980, x-travel 300 mm y-travel 160 mm z-travel 340 mm tool taper SK40 Speed 40-2000 U/min. control Aktiv HEIDENHAIN table-size 600 x 210 mm total power requirement 2 kW weight of the machine ca. 0,73 t dimensions of the machine ca. TBH 1200x1100x1600 m - Active feed in the X and Z axes - Additional swiveling table 600 x 210 mm - Coolant system - Counter bearing for horizontal milling - Several fixtures and clamping devices/milling cutters - Operating instructions Ihedpow A Apyefx Abcew

Condition: used, Year of construction: 1980, x-travel 300 mm Iodpfx Abjw A Ap Hjcohw y-travel 160 mm z-travel 340 mm tool taper SK40 Speed 40-2000 U/min. control Aktiv HEIDENHAIN table-size 600 x 210 mm total power requirement 2 kW weight of the machine ca. 0,73 t dimensions of the machine ca. TBH 1200x1100x1600 m - Active feed in the X and Z axes - Additional swiveling table 600 x 210 mm - Coolant system - Counter bearing for horizontal milling - Several fixtures and clamping devices/milling cutters - Operating instructions

Condition: ready for operation (used), Year of construction: 2003, bore capacity in steel (diameter) 40.0 mm threading M 24 in St 60 throat 293 mm bore stroke 140 mm morse taper 3 Kurzspindel MK table: 514 x 360 mm turning speeds 160 - 2250 U/min column diameter 115 mm throat 293 mm distance spindle /table min 117 / max 701 mm T-slots 2 x 14 x 224 feed 0.1 + 0.2 mm/U total power requirement 1.45 / 1.90 kW weight 370 kg dimensions of the machine ca. 1200 x 800 x 1840 mm current new price ~ 12.500 euros special price on request Equipment: - robust column drill - V-belt - - infinitely variable speed adjustment - analog speed system - automatic spindle feed - thread cutting device - pole-changing drive motor - height-adjustable work table - machined base plate - feed overload protection - Main switch with motor protection switch - Mushroom pushbutton (latching) for EMERGENCY STOP - Spindle protection - Operating instructions in German * Special equipment included : - Thread cutting device * with foot switch, for thread cutting with stop - Machine light - Coolant device in the machine base Iedpfx Abeynbfpecjhw

Condition: ready for operation (used), Use The return conveyor enables single-sided edging machines to be operated by one person. Function The workpieces transported through the machine are taken over by a driven chain unloader supported by a driven roller and placed on an air cushion table. With a pusher and the slanted position of the air cushion table, the workpiece slides out onto a driven return conveyor belt with a belt width of 800 mm and a frame width of 900 mm. There is an undriven roller conveyor in the extension of the belt. Design At the base machine's output, there is a driven chain discharger with a driven roller, an air table with a pusher, a driven return conveyor belt ZFB 05 with a belt width of 800 mm, a frame width of 900 mm, and an undriven roller conveyor with a length of 2000 mm. Workpiece parameters Max. length: 2000 mm Min. length: 300 mm Max. width: 800 mm Min. width: 150 mm (with 40 mm workpiece overhang) Max. thickness: 40 mm Min. thickness: 8 mm Technical parameters Feed: 8 – 42 m/min, infinitely variable Air cushion table: 2000 mm 1000 mm wide approx. 60 mm inclined Pneumatics Air pressure: 6 bar Air consumption: 0.5 NL/min Electronics Control: Relay control Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Total power: approx. 2.2 kW Paint Robust textured paint, gray RDS 240 80 05 Equipment All-way rollers at the end of the air cushion table. For workpieces up to 2600 mm, only in longitudinal feed. Additional equipment for narrow pieces from 60 mm. Widening of conveyor belt to 1100 mm. Frame width 1200 mm per meter. Swivel roller rail. In segments, mounted on the outside of the return conveyor. Interlock for return conveyor. Safety and protective devices Machine with CE marking Built in accordance with EC Machinery Directive 89/392/EWG – Annex IIA Special safety devices of a local nature are not included. Documentation Operating documentation and maintenance instructions in Swedish, number: 1 copy in paper format and 1 copy on CD Original documentation in English, 1 copy in paper format and 1 copy on CD Other documentation such as electrical diagrams, technical descriptions, spare parts lists, etc. in English (included in the original documentation) Operating text for display screen translated into Swedish Edge banding machine HOMAG KLO 78/A20/S2 Technical data Ihedpoytfldjfx Abcsw Steplessly adjustable feed: 18–24 m/min Machine working height: 950 mm Workpiece width min. 55 mm at a thickness of 22 mm 100 mm at a thickness of 60 mm (depending on workpiece length) Workpiece overhang: 30 mm Workpiece thickness: 10–60 mm Edge material thickness (strips): 0.3–20 mm Max. cross-section: 900 mm² Edge material thickness (roll): 0.3–3.0 mm Max. cross-section: – for PVC 135 mm² – for veneer 100 mm² Max. roll diameter: 830 mm Pneumatic connection: 7 – 8 bar Floor conditions must correspond to the foundation drawing. Aggregates Joint milling unit Glue unit A20 Cutting unit HL 83 chamfering and straight cutting Pre-milling unit 1.5 kW – Optimat Fine milling unit 0.4 kW – Optimat Shape milling unit FF12 under/over 0.4 kW Sickling unit for glue joints KS 10 belt sanding unit Chamfering unit above and below with oscillation

Condition: used, Year of construction: 2022, functionality: fully functional, machine/vehicle number: HD 7/16-4ST + HWE 860, This listing refers to a Kärcher high-pressure cleaner HD 7/16-4 ST in combination with a Kärcher Hot Water Generator HWE 860 (stationary unit). The machine has been inspected in our in-house workshop and is fully functional. High-Pressure Cleaner HD 7/16-4 ST / HWE 860 Kärcher Hot Water Generator Product Description: HD 7/16-4 ST With a working pressure of 160 bar, the pre-configured cold water high-pressure cleaner HD 7/16-4 ST serves as an entry-level unit in the range of our stationary HD cleaners with single-lance operation. Our pre-configured cold water high-pressure cleaner HD 7/16-4 ST comes equipped with various features and offers multiple options for individual upgrades. A dry-running protection system and an operating hours counter are included as standard. The unit allows for the suction of one or two detergents in either high- or low-pressure mode and can be optimally configured to its place of operation thanks to an extensive accessory package (see photos). With 160 bar working pressure, this high-pressure cleaner delivers more than sufficient power to tackle even very demanding cleaning tasks. Kärcher innovations such as the EASY!Force high-pressure gun, which reduces the holding force to zero by utilizing the recoil force of the high-pressure jet, and the EASY!Lock quick-release fasteners (enabling five times faster handling compared to conventional screw connections with no compromise on robustness and durability) support the user. Kärcher Electric Hot Water Generator HWE 860: The electric hot water generator HWE 860 is used in conjunction with the HD 7/16-4 ST high-pressure cleaner and heats water up to 85 °C. Operation of this unit requires proper instruction. Description: HWE 860 Kärcher Hot Water/High-Performance Heater The electric hot water generator offers an output of 24 kW. Its use is especially recommended where burner exhaust emission is problematic or not permitted. Maximum temperature is 85 °C, thermostatically controlled. The unit can be operated manually or automatically. The device is used in conjunction with a high-pressure cleaner. Ihsdpfxjymdm Ts Abcew The hot water generator is delivered as a standalone assembly, complete with control cabinet and all necessary components (hoses, cables, clamps, etc.). Optionally, the customer can select between cold and hot water operation via two solenoid valves and opt for a digital timer during configuration. The unit can also serve as an instantaneous water heater—for example, during continuous operation at a flow rate of 700 l/h and an inlet temperature of 15 °C, a temperature of 45 °C is achieved (a temperature increase of 30 °C). TECHNICAL DATA FOR BOTH UNITS AVAILABLE ON THE NAMEPLATES. FOR FURTHER PRODUCT DETAILS ON: HIGH-PRESSURE CLEANER HD 7/16-4 ST HOT WATER GENERATOR HWE 860 WE RECOMMEND CONSULTING THE MANUFACTURER, KÄRCHER. Subject to changes and errors. Do you have any questions, wish for a consultation, or want to view the equipment on-site? You can reach us by phone during our opening hours: Monday-Friday 09:00 - 13:00 and 14:00 - 17:00. Sale is exclusively under our General Terms and Conditions (GTC).

Condition: good (used), Year of construction: 2006, sheet width 2530 mm plate thickness 2.50 mm thickness at "Niro-steel" 1.50 mm no. of strokes 34 Hub/min cutting angle 1.7 Grad table height 820 mm distance between columns 2620 mm Control konv. engine output 4.0 kW weight of the machine ca. 1350 kg. range L-W-H 3100 x 1980 x 1400 mm Features: - robust / motorized swing cut guillotine shears - unbreakable and torsion-free welded steel construction - compact and clear machine construction - manual backgauge, with analog display * Adjustable from the rear * stepless adjustment over the entire travel range Ihsdpfxsym D Dxo Abcsw - all-steel blade, double-edged - 1x hold-down bar - 1x long side stop - 2x front support arms - Support/working table with 10 mm spaced grooves - Selector switch for single and continuous stroke - 1x freely movable foot switch - Operating instructions

Condition: good (used), Year of construction: 2007, cutting diameter 320 mm saw band length 3400 x 27 x 0.9 mm capacity 90 degrees: flat 320 x 400 mm capacity 45 degrees: flat LI 320 x 280 mm capacity 45 degrees: flat RE 320 x 260 mm capacity 60 degrees: flat RE 320 x 140 mm band speed 35 + 70 m/min work height max. 930 mm voltage 400 V total power requirement 2.67 kW weight 950 + 250 kg well-maintained condition (!!) current new price incl. accessories ~ 40.000 Euro special price on request Equipment: - electro-hydraulic vertical mitre bandsaw - with large cutting range and small footprint - Robust material support table - miter cuts are carried out fully automatically * electro-hydraulic miter adjustment left right - Up to 99 cutting programs - Central operation of all machine functions from the front - Loading also possible from above - Precise positioning thanks to accurate measuring system - electro-hydraulic miter adjustment left right - Electro-hydraulic material clamping - electro-hydraulic infeed from the saw arm Isdpeym D Drsfx Abcjhw * steplessly adjustable (cutting pressure control) - Operating instructions (PDF) * Special accessories included : - BAUER material feed unit - Micro-dosing device (spray oiler)

Condition: ready for operation (used), Year of construction: 2021, sheet width 6020 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm back stop - adjustable max. 1000 mm work height max. 1030 mm no. of strokes 5 - 10 Hub/min cutting angle 0.5 - 3.0 ° down holder 33 Stück Control SC 100 T engine output 11.0 kW weight of the machine ca. ca. 27000 kg range L-W-H 7650 x 2400 x 2885 mm New price in 2021 ~ 160.000 Euro Special price upon request Equipment: - Robust electro-hydraulic guillotine shear * Design: Guide rail - HACO CNC control model SC 100 T, pivoting at the front left * Control unit with LCD display * Pre-selected positioning of the backgauge * Digital display of actual position * Electro-hydraulic cutting angle adjustment * Electro-hydraulic cutting gap adjustment * Programmable retraction from the backgauge * Programmable cutting length limitation * Automatic + manual programming mode * Emergency stop switch - CNC electro-motor-driven material/backgauge * On recirculating ball screws Ihsdpfx Ajxaa Dgjbcow * Continuous adjustment up to max. 1,000 mm - CNC electro-hydraulic cutting gap adjustment - CNC electro-hydraulic cutting angle adjustment - Hydraulically operated Material/sheet metal clamp - Front finger guard - Front support table with recessed grips - 1x side stop with mm scale - 1x freely movable foot switch - Rear safety device (light barrier) - Operating instructions (PDF) Optional accessories included: - Sheet metal holding device for thin sheet metal blanks * Optimal positioning of thin sheet metal

Condition: ready for operation (used), Year of construction: 2001, sheet width 3200 mm plate thickness 3.0 mm ST thickness at "Niro-steel" 2.0 mm Opening width / upper beam 300 mm speed OW 40.0 mm/sec Bending beam adjustment 80.0 mm work height max. 900 mm speed BW 90.0 Grad/sec control MULTIBEND 5000 back stop - adjustable 10 - 1550 mm accuracy +/- 0.1 mm air pressure 5.0 bar Number of working hours ca. 1.000 h total power requirement 2x 4.0 kW voltage 400 V weight 4400 kg Isdpjxabz Tofx Abcohw range L-W-H 4295 x 2225 x 1775 mm New price approx. 85.000 euros Machine with only approx. 1.000 operating hours (!!) good condition (!!) Special price on request - in checked condition - machine video - ?v=VP6emx4HTYM ! Maximum flexibility when bending cassettes, boxes and profiles ! High flexibility in bending part design ! High productivity and throughput ! Easy to use Equipment: - motorized universal swivel bending machine "RAS 73.30" * high-precision mechanics with modern control technology * for individual and series production * robust high-speed machine with high axis speeds * torsion-free welded construction - RAS CNC control model "MULTIBEND 5000" * material and tool library * swiveling - front right * 1x emergency stop button - CNC electro-motorized upper beam adjustment * fast closing and opening speed * programmable opening and closing height * bending radii without special tools (multiple bends) * rigid upper beam for straight bending parts * 1x set of RAS split upper tools .. height 80 mm * RAS "click-in" tool system - CNC electro-motorized bending beam adjustment * fast swivel movement: short production time * crowning system compensates for deformation by the bending forces * 1x set of RAS split bending tools - CNC electro-motoric back stop * fast positioning, repeatable work * table plates hold the weight of the sheet * stainless steel table plates with ball rollers - 2x freely movable double foot switch - 1x RAS tool trolley for bending tools (movable) - operating instructions (PDF) + original circuit diagram

Condition: used, functionality: fully functional, Year of construction: 2013, operating hours: 80,087 h, machine/vehicle number: S2321M0007, control type: CNC control, controller manufacturer: SIEMENS, controller model: SINUMERIK, laser type: fiber laser, laser source manufacturer: TRUMPF, laser source model: TruFiber, laser power: 400 W, Equipment: CE marking, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, TruLaser Cell 3000 Highly dynamic and precise CNC laser machine solid polymer concrete machine body cantilever axes system 800 x 600 x 400mm travel X-Y-axes with linear motors direct absolute measuring system Z axis with linear guides and ball screw drives TRUMPF control based on SIEMENS Sinumerik 840D sl panel PC for process monitoring integrated switch cabinet and cooling unit water-air incl. start-up and instruction TruFiber 400 Laser equipment compl. TruFiber 400 (G2) Single mode fiber laser for industrial use in welding and cutting: laser power: 400W at fiber end Ihjdoyvfuwepfx Abcow beam quality: M2 1.1 laser light cable: 6m LLK-B operation mode: Cw / modulated max. modulation frequency: 50 kHz pilot laser: standard Trumpf coil feeding unit design tube • Clamping and guiding for coil material • Length up to 800mm • Thickness from 0,1mm to 1,9 mm • Width from 40 to 250 mm • Width adjustment with Handwheel • Cutted parts guidance in a Boxsystem or a funnelsystem • Pneumatic feeding coil 50mm stroke right • Coil feed control

Condition: as good as new (ex-display), Year of construction: 2019, functionality: fully functional, machine/vehicle number: 801657, type of input current: three-phase, total height: 1,900 mm, input voltage: 380 V, total width: 1,150 mm, total length: 4,250 mm, overall weight: 1,500 kg, working height: 900 mm, compressed air connection: 6 bar, warranty duration: 6 months, air demand: 0.6 m³/h, power: 1.5 kW (2.04 HP), Equipment: documentation/manual, Indexed case packer ZHJ-150 Display machine/ trade fair machine Multifunctional cartoning machine ZHJ-150 The ZHJ-150 automatic cartoning machine is suitable for packaging aluminum-PVC blisters, round bottles and special bottles, molded bottles and similar products. Instruction leaflets can be folded automatically, cartons erected, products fed in and the cartons closed again (offset plug-in closure). The cartons can be embossed. This machine has a PLC control system and each station is monitored by photoelectric sensors. If a problem is detected during operation, the machine stops automatically and indicates the fault. This machine can run as a single machine and can also be connected to a blister packaging machine and other pre-machines. The machine can be inspected at any time at our premises in 73084 Salach/Germany and tested with your products. Depending on the product, it is also possible to order a new machine from us. We also have various blister and cartoning machines to offer. Technical data: max. speed = up to 130 cartons/min Carton size = width (20-90mm) x length (50-190mm) x height (15-60mm) Leaflet size unfolded = Max.240x180mm (LxW) / Min.115x100mm (LxW) Leaflet folder = up to 3 paper folds possible Blister feeder magazine = 100cm long / number of blisters/cartons to be packed selectable Bottle feeder = screw conveyor Ihjdpfxotib Uys Abcjw Leaflet control in folding box available Automatic ejection of bad packs

Condition: new, No. 3183 Ijdju Tipkjpfx Abcehw Vacuum dryer / drying chamber ISVE ES 3 / NEW New machine, delivery time 120 days Construction features: AISI-304 stainless steel, partially insulated External diameter: 1300 mm Length of cylindrical part: 5000 mm Dryer length: 5900 mm Dryer total length plus sliding guides: 11000 mm Max. operating vacuum: -730 mm Hg Timber pile length: 5000 mm Timber pile width: 800 mm Timber pile height: 790 mm Net wood volume: approx. 2,5 m3 Installed electrical power: 8,80 kW Average hourly power input: 4,4 kW/h Includes: - 9 electric heating plates (each 800 x 5000 x 10 mm LWH / 40 kg / 0,695 kW) - 1 oil vacuum pump (65 m3/h / 1,8 kW / 380 Vca) - 1 vacuum pump condenser (stainless steel tube with internal condensation system) - 2 internal condensers (turbofan of 0,37 kW each 380 VCa) - 2 one-way valves (clapet: one ¾” for vacuum circuit; one ½” for condenser discharge) - 1 solenoid air return valve (24 Vca: one 1” for the autoclave and one ½” for the condenser) - 1 manual air return (1” ball valve) - 1 electrical control panel (PLC type Siemens S7-1200, with touch panel) - 1 ISVE server connect with remote service and control - 2 wireless moisture probes (double probes for core and surface moisture reading) - 1 wireless temperature probe (for wood core reading) - 2 plates-holder stands - 1 instruction booklet (in English with CE certificate and wiring diagrams) Transport dimensions approx. 5900 x 1300 x 2000 mm LWH Weight approx. 2000 kg Technical details, year of construction and scope of delivery according to the manufacturer, without guarantee Subject to prior sale New machines are covered by the manufacturer's warranty Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: new, No. 3171 Vacuum drying kiln ISVE ES 2 / NEW New machine, delivery time 120 days Construction features: AISI-304 stainless steel, partially insulated External diameter: 1000 mm Length of cylindrical part: 5000 mm Dryer length: 5900 mm Dryer total length plus sliding guides: 11000 mm Max. operating vacuum: -730 mm Hg Timber pile length: 5000 mm Timber pile width: 800 mm Timber pile height: 400 mm Net wood volume: approx. 2 m3 Installed electrical power: 5,27 kW Average hourly power input: 2,7 kW/h Includes: - 6 electric heating plates (each 800 x 5000 x 10 mm LWH / 40 kg / 0,695 kW) - 1 oil vacuum pump (40 m3/h / 1,1 kW / 380 Vca) - 1 vacuum pump condenser (stainless steel tube with internal condensation system) - 2 one-way valves (clapet: one ¾” for vacuum circuit; one ½” for condenser discharge) - 1 solenoid air return valve (24 Vca: one 1” for the autoclave and one ½” for the condenser) Ihjdjuvi Sajpfx Abcsw - 1 manual air return (1” ball valve) - 1 electrical control panel (PLC type Siemens S7-1200, with touch panel) - 1 ISVE server connect with remote service and control - 2 wireless moisture probes (double probes for core and surface moisture reading) - 1 wireless temperature probe (for wood core reading) - 2 plates-holder stands - 1 instruction booklet (in English with CE certificate and wiring diagrams) Transport dimensions approx. 6100 x 1150 x 1300 mm LWH Weight approx. 1300 kg Technical details, year of construction and scope of delivery according to the manufacturer, without guarantee Subject to prior sale New machines are covered by the manufacturer's warranty Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location