Used Press Corner for sale (14,620)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Lredpfozuzw Dsx Abtsr Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Lrodpfozuzwwex Abtsr Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Lodpfxozuzwqs Abtorr Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Lodpfjzuzwkjx Abterr Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Ljdpfx Abjzuzv Tstjrr Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Ledpfjzuzvmox Abtsrr Technical data Voltage: 400 V Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: new, Year of construction: 2026, functionality: fully functional, input voltage: 400 V, input current: 380 A, type of input current: three-phase, pressing force: 40 t, stroke length: 100 mm, operating speed: 9 mm/s, reverse speed: 80 mm/s, table length: 1,320 mm, table height: 290 mm, throat depth: 180 mm, ram plate length: 500 mm, clearance between the columns: 900 mm, retraction force: 40 t, total length: 1,500 mm, total width: 1,300 mm, total height: 1,800 mm, overall weight: 1,500 kg, controller model: Estun NC E21, motor manufacturer: Siemens, Equipment: CE marking, documentation/manual, hydraulics, safety light barrier, The Digima WCY-40T/1320 hydraulic press brake is a compact and robust machine designed for the precise bending of sheet metal and smaller metal components. Its space-saving dimensions make it an excellent choice for metalworking workshops, manufacturing plants and companies producing enclosures, guards, panels, profiles and various technical components. The machine provides a nominal pressing force of 400 kN, equivalent to 40 tonnes, and a working-table length of 1,320 mm. The distance between the columns is 900 mm, the throat depth is 180 mm, the ram stroke is 100 mm, and the maximum open height is 290 mm. The back gauge offers an adjustment range of up to 500 mm, enabling the sheet to be positioned accurately before bending. The Digima WCY-40T/1320 is equipped with an Estun E21 NC control system, which controls the position of the back gauge on the X axis and the working position of the Y axis. The controller includes an operation counter, intelligent positioning, screw-backlash compensation and a function that retains the programmed position after the power supply has been switched off. A positioning resolution of 0.1 mm or 0.01 mm supports accurate and repeatable production. The press brake is powered by a 3 kW Siemens main motor. Its hydraulic system uses Bosch-Rexroth components and a Sunny hydraulic pump, while the electrical system includes Schneider Electric components. PARKER seals and guide rings increase the durability of the working mechanisms and support reliable operation during intensive daily use. Lsdpezlqkuofx Abterr The ram approach and return speeds are 80 mm/s, while the working pressing speed is 9 mm/s. These parameters enable efficient machine positioning and smooth bending operations. The rigid monoblock steel frame is welded and heat-treated to provide high structural stability and resistance to deformation under load. The machine is equipped with side guards, a front safety curtain, protection against excessive hydraulic pressure and high oil temperature, motor overload protection, electrical leakage protection and a safety relay. The electrical cabinet has an IP65 protection rating, and the press brake is CE-certified. The standard equipment includes bending tools, two front material-support arms, a foot-control pedal, foundation bolts, spare sealing rings and mechanical and electrical documentation. The upper punch features an 86° working angle and an R0.5 tip radius, while the multi-V lower die allows the operator to select a suitable bending position according to the type and thickness of the material. The Digima WCY-40T/1320 is a practical, user-friendly and economical press brake for companies requiring a reliable machine for the everyday processing of small and medium-sized components. Its combination of a 40-tonne pressing force, a 1,320 mm working length, NC control and high-quality branded components makes it suitable for both one-off projects and small batches of repeatable parts.

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Lredpfxozuzi Ts Abtor Year of manufacture: 2001 Technical data - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Length: 2 x 2,600 mm - 2 x 2,620 mm Width: 2,070 mm Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Note: Upon request, the complete layout plan of the system can be sent. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1998, - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Door pressing system Manufacturer: Wild Year of manufacture: 1998 For door dimensions: - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Consisting of the following sections: 1. Continuous door panel gluing with frame assembly station / 2. Pressing line with hardboard facing station Section 1 consists of: - Gantry loading system - Angle transfer with longitudinal and cross saws - Loading and feeding of the longitudinal and transverse frame parts from magazines - Longitudinal cutting station for the longitudinal frame parts - Connecting station of the frame parts with the door panel core. With clamping devices - Conveyor belt angle transfer with shuttle transfer of the door panel cores onto the glued hardboard Section 2 consists of: - Loading of the hardboard - Brush cleaning machine - Hardener application machine from below - Glue application machine from below - Roller conveyor - Angle transfer for the lower hardboard Lrsdszuzgropfx Abtor - Vacuum reversing device for the upper hardboard - Automatic facing station for hardboard and door panel cores - 2 door presses, each with 2 x 4 pressing stations, arranged parallel to each other - Both presses are loaded at the infeed with 1 shuttle loading basket - Both presses are unloaded at the outfeed with 1 shuttle unloading basket - Angle transfer to the infeed into a hedgehog buffer - Angle transfer at the outfeed of the hedgehog buffer and feeding to the stacking station - One-sided vacuum stacking with protective plate space Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: excellent (used), functionality: fully functional, Catalogue number 7364 TECHNICAL DATA - max. workpiece height: 160 mm - spindle working length: 250 mm - spindle diameter: 40 mm - max. tool diameter: 220 mm - working table (L/W): 410x1000 mm - motor: 11 kW - 2 pneumatic material clamps - extraction port diameter: 160 mm - dimensions (L/W/H): 1070x1260x1400 mm - weight: 650 kg ADVANTAGES – Made in Germany – Additional set of cutters + copy template – Not repainted – Used milling machine, in very good condition Lrodpjztaq Tofx Abtsr Net price: 33,900 PLN Net price: 8,070 EUR according to 4.2 exchange rate (Prices may change with significant exchange rate fluctuations)

Condition: new, Year of construction: 2026, pressure 28 t stroke 180 mm table-size 300 x 550 mm diameter of piston 130 mm work speed min. 2 m/sec work speed max. 9,8 m/sec return speed 20 mm/sec Max. pressure 200 bar Lodpsgvkmrefx Abterr weight of the machine ca. 0,65 t total power requirement 4 kW dimensions of the machine ca. 1,15 x 0,75 x 1,1 m • The horizontal bending and straightening press from Profi Press is a universal one Hydraulic press specially designed for performing bending, profiling and Straightening work is designed. The applications of the machine are different and depend on the accessories that are on the work table, the Tool holder and are installed in the holes and pin holes. • The HB-28 model is used for light bending measurements on the work table equipped with an angle scale, and the press can also be equipped with tools are supplied (for example block punching) that are placed on the tool holder Can be assembled, as well as tools that are in the holes and pin holes can be installed to carry out various types of work. • The hydraulic system can be adjusted with the help of the pressure and flow adjustment valves can be regulated, which is the pressing force and the speed of the press influence. The press is equipped with a built-in manometer. • The control panel is used to operate and display the piston stroke and for Choice between manual or automatic operation, and the HB-28 model is also with a built-in memory for up to 4 different programs fitted. • Operation is via electric foot pedals. • The Profi Press HB-28 model can be equipped with various optional accessories hearing parts and tools for installation on the workbench and the Tool holder to be delivered.

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, total width: 2,420 mm, total length: 6,840 mm, total height: 2,600 mm, overall weight: 15,000 kg, type of input current: three-phase, filling opening length: 2,000 mm, filling opening width: 1,980 mm, input voltage: 400 V, empty load weight: 4,950 kg, DGUV certified until: 08/2027, Presto HGS20R 2 units available Container for skip loader trucks 20 cubic meter usable volume Lredpfszt Nirjx Abtjr Technically refurbished Repainted in desired RAL color Side hook connection Discharge door hinged at the top

Condition: used, The SANDT Type 410 is for DIE-Cutting of difficult materials, particularly in the leather goods and printing industries, leather goods, cardboards and plastic. Schwenkarmstanze / hydraulic Clicking Press SANDT Typ 410 Serial-No. 760044 Stanzkraft / Pressure 22000kgs Stanzfläche / Die Cutting area max. 650 x 650mm Tischfläche / Cuttig Surface max. 550 x 900mm Hub 0 - 60mm Abmessungen / machine dimension 900 x 870 x 1400mm Gewicht / weight 840kg Online-Video-Inspection by WhatsApp - MS Zoom - Telegram Lredpfxezukivo Abtor On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: used, Platen press, 1300x2500 mm, 20/26. Lredpfezvmkxsx Abtsr

Condition: used, We are offering for sale a floor-type press made by the Italian manufacturer Colombo R. Available for immediate delivery. Lrjdjzry Rwopfx Abter

Condition: good (used), We offer a variety of tools for press brakes, almost exclusively from the brand Trumpf: OW / OWZ: Upper tool (punch), Top Tool UW / UWZ: Lower tool (die/matrix), Bottom Tool/Die Details, prices, and specifications: 1) Top Tool (Punch) – OW 210/S (R1 / h-240 / 28°) Set composition: 3 pcs x 500 mm, 8 pcs x 300 mm, 2 pcs x 250 mm, 4 pcs x 200 mm, 1 pc x 170 mm, 1 pc x 140 mm, 1 pc x 110 mm, 3 pcs x 100 mm, 2 pcs x 100R mm, 2 pcs x 100L mm, 1 pc x 75 mm, 2 pcs x 50 mm, 1 pc x 45 mm, 1 pc x 40 mm, 2 pcs x 35 mm, 2 pcs x 30 mm, 2 pcs x 25 mm. Total set length: 6,760 m Price per meter: 1,270 € Total set price: 8,584 € 2) Top Tool (Punch) – OW 200/S (R1 / h-220 / 86°) Set composition: 7 pcs x 300 mm, 7 pcs x 200 mm, 1 pc x 100R mm, 1 pc x 100L mm. Total set length: 3,700 m Price per meter: 1,111 € Total set price: 4,111 € 3) Bottom Tool (Die) – EV 004 - W12 (R1 / h-150 / 30°) Set composition: 5 pcs x 500 mm, 1 pc x 200 mm, 1 pc x 180 mm, 3 pcs x 100 mm, 1 pc x 55 mm, 1 pc x 50 mm, 1 pc x 45 mm, 1 pc x 40 mm, 1 pc x 35 mm, 1 pc x 30 mm, 2 pcs x 25 mm. Total set length: 3,485 m Price per meter: 952 € Total set price: 3,319 € 4) Top Tool (Punch) – OW 202 K (R1 / h-120 / 28°) Set composition: 6 pcs x 500 mm, 1 pc x 300 mm, 1 pc x 200 mm, 1 pc x 100 mm, 1 pc x 100R mm, 1 pc x 100L mm, 1 pc x 50 mm, 1 pc x 45 mm, 1 pc x 40 mm, 1 pc x 35 mm, 1 pc x 30 mm, 2 pcs x 25 mm. Total set length: 4,050 m Price per meter: 873 € Total set price: 3,536 € 5) Bottom Tool (Die) – EV 004 - W12 (R1 / h-100 / 30°) Set composition: 6 pcs x 500 mm, 1 pc x 300 mm, 1 pc x 200 mm, 3 pcs x 100 mm, 1 pc x 50 mm, 1 pc x 45 mm, 1 pc x 40 mm, 1 pc x 35 mm, 1 pc x 30 mm, 2 pcs x 25 mm. Total set length: 4,050 m Price per meter: 794 € Total set price: 3,214 € 6) Bottom Tool (Die) – EV/S-W10 (R1 / h-100 / 84°) Set composition: 2 pcs x 500 mm. Total set length: 1,000 m Price per meter: 714 € Total set price: 714 € 7) Top Tool (Punch) – OW 280/K (R0.5 / h-140 / 80°) Set composition: 1 pc x 500 mm, 1 pc x 300 mm, 1 pc x 100R mm, 1 pc x 100L mm, 1 pc x 100 mm, 1 pc x 50 mm, 1 pc x 45 mm, 1 pc x 40 mm, 1 pc x 35 mm, 1 pc x 30 mm, 2 pcs x 25 mm. Total set length: 1,350 m Price per meter: 873 € Total set price: 1,179 € 8) Bottom Tool (Die) – EV 005 W16 (R1.6 / h-150 / 30°) Set composition: 6 pcs x 500 mm, 1 pc x 300 mm, 3 pcs x 100 mm, 1 pc x 50 mm, 1 pc x 45 mm, 1 pc x 40 mm, 1 pc x 35 mm, 1 pc x 30 mm, 2 pcs x 25 mm, 1 pc x 200 mm. Total set length: 4,050 m Price per meter: 952 € Total set price: 3,857 € 9) Bottom Tool (Die) – EV 006 W 20 (R2 / h-150 / 30°) Set composition: 6 pcs x 500 mm, 2 pcs x 300 mm, 1 pc x 200 mm, 3 pcs x 100 mm, 1 pc x 50 mm, 1 pc x 45 mm, 1 pc x 40 mm, 1 pc x 35 mm, 1 pc x 30 mm, 2 pcs x 25 mm. Total set length: 4,350 m (Note: The actual mathematical sum of the segments listed is 4,350 mm, although the original sheet textually noted 4,025 mm). Price per meter: 952 € Total set price: 4,143 € 10) Bottom Tool (Die) – EV 007 W40 (R2.5 / h-150 / 30°) Set composition: 5 pcs x 500 mm. Total set length: 2,500 m Price per meter: 873 € Total set price: 2,183 € 11) Bottom Tool (Die) – TS 20.211 V40 (R4 / h-40 / 85°) – Manufacturer: TS Tecnostamp Lodpfezrw A Rsx Abterr Set composition: 1 pc x 835 mm, 1 pc x 505 mm, 1 pc x 165 mm, 1 pc x 100 mm, 1 pc x 60 mm. Total set length: 1,665 m Price per meter: 278 € Total set price: 463 € Tool Package Summary: Total length: 36,960 m Special package price for the complete lot (Bundle discount): 32,750 €

Condition: good (used), functionality: fully functional, stroke length: 300 mm, throat depth: 450 mm, controller manufacturer: Delem, controller model: DA65, working width: 4,300 mm, bending force (max.): 300 t, distance between stands: 3,700 mm, control type: CNC control, number of support arms: 2, number of axes: 4, type of crowning: CNC-controlled, actuation type: hydraulic, Equipment: CE marking, centralized greasing system, documentation/manual, emergency stop, finger protection, foot remote control, lower tooling, safety light barrier, upper tooling, Bending capacity: 300 Ton Bending length: 4.300 mm Distance between columns: 3.700 mm Back gauge: 550 mm Stroke length: 300 mm Throat: 450 mm Rapid approach speed: 120 mm/sec. Bending speed: 10 mm/sec. Return speed: 120 mm/sec. Controller: Delem DA65 Featured with: - Y1, Y2, X & R-axis controlled - CNC Hydraulic crowning - Various sets of bending tools - Laser safe curtain Lazer Safe - Machine manual and documentation Country of origin: The Netherlands Lsdjydpxvjpfx Abtorr Motor power: 30 kW Machine LxWxH: 510 x 200 x 330 cm Machine weight: 21.500 kg

Condition: good (used), pressing force: 50 t, stroke length: 320 mm, Capacity 50 Ton Throat 225 mm Adjustable stroke 8 - 100 mm Number of strokes 320 p/min Ram size 300 x 280 mm Ledpfstt A T Tsx Abterr Table size 500 x 800 mm Machine LxWxH: 160 x 120 x 260 cm Machine weight: 6 Ton

Condition: good (used), pressing force: 80 t, throat depth: 400 mm, ram adjustment: 80 mm, Capacity: 80 Ton Table surface: 750 x 550 mm Ram Adjustment: 80 mm Stroke length: 8 -112 mm No. of strokes: 78 p/min. Throat: 400 mm Complete with: - Pneumatic clutch - Safety screen Lredeugtkxepfx Abtsr Country of origin: Germany Machine LxWxH: 2000 x 1200 x 2900 mm Machine weight: 7000 kg

Condition: used, Technical specifications: Max. dimension of glued component: 1600 x 3000 mm 3 vertical presses 2 horizontal presses Hydraulic presses Power supply: 400 V Motor power: 1.5 kW Motor speed: 1450 rpm Lrodeyv Atrepfx Abtjr Overall dimensions: Length: 1200 mm Width: 3500 mm Height: 2500 mm

Condition: used, Year of construction: 1991, functionality: fully functional, Heidelberg MOZP (1991) – 2-Color Offset Printing Press with Perfecting (1/1 or 2/0) Short Technical Description / Summary High-performance 2-color sheetfed offset press Heidelberg MOZP, year 1991. Features an integrated perfecting unit (P) allowing dual capability: printing 2/0 (two colors on one side) or 1/1 (one color on both sides in a single pass). Renowned for exceptional registration accuracy, high durability, and consistent print quality. Key Technical Specifications Manufacturer: Heidelberger Druckmaschinen AG Model: MOZP (P = Perfecting / Свртувач) Year of Manufacture: 1991 Serial Number (Masch. Nr.): 612 123 Country of Origin: Germany Number of Printing Units: 2 colors Max. Sheet Size: 480 x 650 mm (18.9" x 25.6") Lodpfozur E Sox Abtjrr Min. Sheet Size: 140 x 185 mm Max. Printing Speed: Up to 10,000 sheets/hour Plate Size: 525 x 650 mm Weight: approx. 5,200 kg Features & Equipment CPC 1-01 / CPC Control Desk: Centralized remote ink and register control console. Perfecting Unit (1/1 or 2/0): Quick convertible unit for straight printing or perfecting options. Alcolor / Standard Dampening System: Continuous dampening system for fast ink-water balance. Powder Sprayer: Integrated anti-setoff powder spray device. Quick-action plate clamps for fast job changeover. Standard stream feeder and high-pile delivery. Condition & Availability Condition: Used, clean, visually very good, well-maintained in a professional printing environment.

Condition: excellent (used), Catalogue number 7737 TECHNICAL DATA - Pressing force: hydraulic - Briquette shape: round - Briquette diameter: 70 mm - Hopper diameter: 1000 mm - Throughput: approx. 70 kg/h - Automatic machine operation - Motor: 5.5 kW - Dimensions (L/W/H): 1800x1150x1540 mm - Weight: 900 kg ADVANTAGES Lrodpjzrnvzofx Abtsr – Italian manufacture – Used briquetting press – DTR technical documentation – Condition: very good Net price: 34,900 PLN Net price: 8,300 EUR (based on the rate of 4.2 EUR) (Prices may change with significant exchange rate fluctuations)

Condition: good (used), Year of construction: 2007, functionality: fully functional, operating hours: 94,201 h, bending force (max.): 400 t, installation height: 595 mm, control type: CNC control, Bending length [mm] 3550 Pressing force [tons] 400 Control system Cybelec ModEva 10s Standard equipment: - Sturdy machine frame as a welded construction in all-steel design - Press beam with high bending strength - Electro-hydraulic upper drive via proportional valves - Modern block hydraulics - CNC rear stop for X and R axes, safe displacement of the stop fingers from the front by means of a safety interlock - Upper tool clamping system "EHT", manual, head width 26mm, load max. 3000 kN/m - Lower tool clamping system EHT, manual, clamping width 90mm for block tools and 13mm for single V-dies, without clamping - Control system: CYBELEC ModEva 10S on Windows, 2D graphic control with a 10.4" color screen - Control cabinet air conditioning + Rear stop - System 1, 5 axes, straight finger, 140mm wide, adjustment of R axis 150mm + EHT quick clamping device, Ledsy Saurepfx Abtjrr for upper tools, pneumatic, head width 26mm, load max. 3000 kN/m (self-centering horizontally) + EHT lower tool clamping, pneumatic, clamping width 55mm + Hardened insert strip, for EHT lower tool clamping 55mm / 90mm + Lower tool displacement, CNC-controlled, infinitely adjustable via rear stop 1 (max. 4550 mm working length) + Crowning device CNC-controlled, in the table without tool clamping, load max. 3000 kN/m + Safety device LaserSafe (up to max. upper tool height 440mm) + Additional foot switch + Bending aid 1st arm, load max. 1500N with 2 integrated support strips in standard design + Bending aid 2nd arm, load max. 1500N with 2 integrated support strips in standard design + 2 pcs. support strips for a bending aid with T-slot 14mm and scale and ball rollers + 2 pcs. table extension for bending aid + Short park position left + Short park position right

Condition: good (used), Year of construction: 2010, functionality: fully functional, bending force (max.): 85 t, installation height: 615 mm, number of axes: 6, Equipment: CE marking, documentation/manual, safety light barrier, Bending length [mm] 2720 Press force [t] 85 Control unit TRUMPF TASC 6000 Operating hours [h] 45666 Hydraulics on [h] 13762 - Top drive concept in four-cylinder design Y1/Y2 - Electrohydraulic ram drive with proportional valve technology - Ram position measuring system with deflection compensation via glass scales - Modern block-type hydraulics - Spherical suspension and inclined position of the pressure beam - CNC backgauge system - Safe finger adjustment from the front - 2 stop fingers - Self-centering, manual, hardened upper tool holder for vertical tool change - Hardened, manual lower tool clamping - Program-controlled lower tool displacement (I-axis) for 2 positions - Flat front cover - Modern safety guard - CE mark - Oil cooler clamping device Ljdpfx Asy Saq Tjbtjrr - Increased installation height - 6-axis backgauge - Hydraulic upper tool clamping - Hydraulic lower tool clamping - CNC crowning - CNC I-axis - BendGuard - ACB preparation - 2 support consoles

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, power: 44 kW (59.82 HP), pressing force: 500 t, stroke length: 300 mm, operating speed: 9 mm/s, throat depth: 400 mm, clearance between the columns: 5,050 mm, total length: 7,500 mm, total width: 4,200 mm, total height: 5,900 mm, overall weight: 67,000 kg, T1 and T1 bending aid for supporting arm EASY FORM angle measuring and correction system Oil tank, 650 liters Set of universal LVD tooling Lightly used under power in Germany New price: EUR 650,000 Lodpfx Abozuyyqotorr Max. bending length: 6100 mm Distance between columns: 5050 mm Max. pressing force: 500 tons Distance beam to table: 570 mm Beam stroke: 300 mm Table width: 200 mm Throat depth: 400 mm Approach speed: 100 mm/min Working speed: 9 mm/min Return speed: 80 mm/min Adjustment of X-axis back gauge: 1000 mm Number of controlled axes: 9 Control: TOUCH Crowning: Yes Hydraulic tool clamping: Yes Power: 44 kW Length: 7500 mm Width: 4200 mm Height: 5900 mm Weight: 67,000 kg