Used center lathes 0-299mm turning diameter over bed for sale (113)

Condition: used, Year of construction: 1975, Technical details: turning diameter over bed: 400 mm turning diameter over support: 220 mm turning length: 1100 mm centre height: 180 mm spindle passage: Ø 45 mm range of revolution per miute: 31,5 - 1.400 / 12 step U/min range of feed in x - axis: längs: 0,08 - 1,10 m/min range of feed in y - axis: quer: 0,028 - 0,40 m/min tailstock quill taper MT: MK4 tailstock quill adjustment: 200 mm total power requirement: 4,0 kW weight of the machine ca.: 1,7 t dimension machine xH: 2,5 x 1,1 x 1,4 m Equipment: -Three-jaw chuck Ø 250mm manufacturer Forkardt with interchangeable jaws -Multifix steel holder Ncodpfx Aju Ix E Hsqvst -Cooling water device with pump -chuck guard -chip collecting tray -chip guard Accessories: -chuck spanner -tool holder -2 pieces gears *

Condition: used, machine/vehicle number: 1717, Used lead and feed screw lathe WEILER PRAKTIKANT Ncodouqb Emepfx Aqvjt Centre height: 140 mm Distance between centres: 500 mm Spindle bore: 36 mm Spindle speeds: 42–2,000 rpm Equipped with RSF 3-axis digital readout, 1 pc 3-jaw chuck Ø160 mm, Chuck guard electrically interlocked, With Multifix toolpost size A with 3 holders Lever-operated collet device with 15 collets. The machine is located at our facility in 71334 Waiblingen-Beinstein and is immediately available. Viewing of the machine is possible by prior arrangement.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and feed spindle table lathe in excellent condition! Technical specifications: >> Machine no. 2801 >> Center height 120 mm >> Center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps Njdpfsv Tyzcex Aqvect >> Spindle bore 23 mm >> Short-taper spindle head DIN 55027 >> Tailstock MT 2 >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x Röhm 125 mm three-jaw chuck with 4 sets of jaws >> Collet chuck with collets from 2 mm to 12 mm, increments of 1 mm Drawbar >> Multifix size A with 4 tool holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle cover >> Clamping tool About the machine: Offered is a Weiler Primus table lathe with guide rail and drawbar in very good condition. The machine is fully functional. All slides run very smoothly and evenly. Even at high speeds, the Weiler runs quietly. The Primus comes from a state-owned company where it was used little. This newer generation of Weiler lathes is very user-friendly, and surfaces can be produced with a polished finish. Take advantage of the opportunity to view this machine on-site under power and see for yourself its condition. (The base cabinet is included; the machine is not bolted to the machine.) A digital display is available for an additional charge.

Condition: used, functionality: fully functional, Weiler Matador VS-2 guide and feed spindle lathe Technical data: Nsdpfjvv Etvex Aqvsct >> Year of manufacture approx. 1970 Machine no. M1012 >> Center height 140 mm >> Center width 500 mm >> Speed: 30 – 3550 rpm >> Spindle passage 36 mm >> Short taper spindle head DIN 55022-5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.010 to 1.184 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 15 mm >> Weight approx. 700 kg >> Length 1.4 m, height 1.2 m, depth 0.55 m Accessories and equipment: >> Collet device 32 collets (set is not complete) with holder >> 1 three-jaw chuck 1 set of jaws >> 1 four-jaw chuck 1 set of jaws >> Mulifix size A with 2 steel holders >> Change gears >> Bed stop About the machine: A used Weiler Matador VS-2 is offered in a fully functional condition. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: used, thickness . mm width . mm length . mm Changing room equipmentLockers: 1 piece All without contents 59 doors 2 lockers 3 lockers 4 lockers 5 lockers Benches: 5 pieces L: 2000 D: 335 H: 400 Cloakroom racks: The tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity Nodpfx Aeyqvw Soqvect More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - 1x empty tool cabinet Nodpfjxq Hhyjx Aqvsct - Emergency stop button - Operating instructions

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min Ncjdpfx Ajxmakyeqvst total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - HEIDENHAIN 3-axis digital display “VRZ 773” - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - 1x empty tool cabinet - Emergency stop button - Operating instructions

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm Ncedpfx Aqjxnda Uovot turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - HEIDENHAIN 3-axis digital display “VRZ 773” - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - 1x empty tool cabinet - Emergency stop button - Operating instructions

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Equipment: - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - KLOPFER three-jaw chuck Ø 140 mm Nedsxacgdopfx Aqvjct - collet holder with lots of collets - foldable lathe chuck guard - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock - adjustable bed stop - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall - emergency stop button, bottom right - machine swing feet - original operating instructions

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 Nedexaccxopfx Aqvoct quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Equipment: - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - collet holder with lots of collets - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock - adjustable bed stop - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Equipment: Ncedpfx Aqexacirevot - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - KLOPFER three-jaw chuck Ø 140 mm - collet holder with lots of collets - foldable lathe chuck guard - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock - adjustable bed stop - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall - emergency stop button, bottom right - machine swing feet - original operating instructions

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Equipment: - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - collet holder with lots of collets - foldable lathe chuck guard - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock - adjustable bed stop - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall - EMERGENCY OFF button, bottom right Nedpfoxaal Dox Aqvoct - machine swing feet

Condition: used, turning length 800 mm turning diameter 280 mm turning diameter over slide rest 150 mm spindle bore 42.0 mm Nsdpfjxacg Rsx Aqvsct tailstock quill taper MT 3 MK bed width 208 mm turning speeds 42 - 2022 U/min spindle taper DIN 55027/5 quill stroke 90.0 mm voltage 380 V total power requirement 3.0 kW weight of the machine ca. 750 kg range L-W-H 1800 x 800 x 1250 mm Due to its design (type, performance, feed rates, etc.) it can be used successfully in training workshops, but also for toolmaking and repair shops. Equipment: - robust conventional lead/spindle lathe - WMW 3-jaw chuck Ø 150 mm - faceplate 280 mm - MULTIFIX quick-change holder, with insert - movable tailstock - chuck key - machine base with storage area - pole-changing drive motor - operating instructions

Condition: ready for operation (used), DROOP & REIN SZ 100 / Keyway Broaching Machine for Lubrication Grooves - Maximum machinable diameter: 140 mm - Spindle bore: 40 mm - Groove length per stroke: 100 mm - Distance between chuck and tailstock center: 350 mm - 3 working speeds - Electric chuck guard - Good / fully operational condition Dimensions: LxWxH 0.9x0.6x1.5 meters / Weight: 300 kg Nsdoyl R Etepfx Aqvect Subject to errors and omissions

Condition: used, Year of construction: 2019, operating hours: 5,900 h, functionality: fully functional, Automatic Tool Presetter, Belt-Type Chip Conveyor, Tailstock with Hydraulic Quill, User-Definable Macros, Visual Part Programming System, Part catcher. Nodpfsxp Hn Dsx Aqvjct

Condition: used, Precision Lathe BOLEY Type 4 LE Conventional High-Precision Universal Multi-Function Machine Tool Serial No. 42562 Centre Distance 500 mm Swing over bed 240 mm Centre height over bed 120 mm Swing over cross slide 140 mm Centre height over cross slide 70 mm Spindle bore 23 mm Chuck mounting M40 x 3.5 mm external thread Tailstock taper MK 2 Quill stroke / travel 80 mm Spindle speed 30 - 1300 rpm Drive power 1.1 kW Power supply 400 V, 50 Hz - 3-axis digital readout RSF ELECTRONIC, Type Z503ST-220 - Position display HEIDENHAIN, Type VRZ 136B for rotary encoder - LCD display unit for measuring equipment on accessories - Spindle speed adjustable via 2 V-belt stages, 2 gear stages, and infinitely variable via variator belt drive - Longitudinal feed via change gears + set of change gears - Several 3-jaw and 4-jaw chucks Ø 100, 125, and 140 mm with chuck jaws - MULTIFIX quick-change tool post size A with 8 exchangeable tool holders - Vertical slide with clamp - Several clamps and vices - Clamping plates + fixture tables - Indexing table as dividing attachment - Dividing head with collets and tailstock - Heavy dividing attachment with clamping plate and handwheel drive - WOHLHAUPTER spindle tools and milling cutters + collets - Rapid-traverse spindle with pneumatic drive - Milling slide with collet chuck Ncjdpfx Asw Dvv Asqvot - External cylindrical grinding attachment - Live centre - Steady rest - VOGEL central oil lubrication - Built-in mini compressor (3.5 bar) in machine base - Compressed air maintenance unit for tooling - Operating manual - Machine mounted on steel plate (steel plate 1200 x 540 x 20 mm) Required space (L x W x H) 1650 x 950 x 1750 mm Weight lathe 660 kg (with steel plate) Weight of accessories 325 kg Very good condition

Condition: good (used), functionality: fully functional, spindle bore: 37 mm, turning diameter: 250 mm, turning diameter over bed slide: 250 mm, center height: 125 mm, turning length: 1,000 mm, total length: 1,500 mm, total width: 800 mm, total height: 1,200 mm, spindle speed (max.): 2,000 rpm, rotational speed (max.): 2,000 rpm, Manufacturer: Harrison Model: M-250 Ncjdex Rrpfopfx Aqvot Condition: Used Maximum turning diameter over bed: 250 mm Maximum turning length between centers: 1000 mm Spindle bore: 37 mm Maximum spindle speed: 2000 rpm Spindle mount: Camlock Toolholder type: Drehblitz Machine dimensions (L x W x H): 150x80x120 Connection voltage: 400 V Cooling system: Yes Digital readout: Yes, 2 axes

Condition: good (used), Centre distance: 450 mm Centre height: 120 mm Spindle bore: 23 mm Speed: 40 – 3000 rpm Infinitely variable drive with 3 gearbox stages and digital speed display Nodpfx Aqow I A Uxsvsct Tailstock: MT 2 Drive power: 1.5 kW Weight: 350 kg Dimensions: 1200 x 650 x 1330 mm Paint: Reseda green RAL 6011 Digital display: Optional at extra cost Accessories: Further accessories available on request

Condition: excellent (used), functionality: fully functional, High-Precision Lead and Feed Screw Lathe Model B30 LZS with Accessory Cabinet and 3-Axis Fagor DRO from UNI Technical Data: >> Centre Height: 120 mm >> Centre Distance: 560 mm >> Spindle Bore: 30 mm >> Max. Swing Diameter: 250 mm >> Longitudinal and Cross Feeds Ncjdpfx Aqexyh Ndovet >> Thread Cutting: Metric, Module, Inch >> Infinitely variable spindle speeds from 30–3000 rpm Accessories: - 3-Axis Fagor Digital Readout - Tool cabinet including: >> 3-jaw chuck >> 4-jaw chuck >> Toolholder >> Drill chuck; live centre >> Collet chuck with collets >> Fixed and travelling steady rest >> Machine feet >> And much more About the Machine: Offered is a Lorch high-precision lead and feed screw lathe in very good condition. The machine is, of course, fully functional. All slides move smoothly and evenly. The machine runs quietly, even at high speeds. Equipped with a 3-axis Fagor digital readout and a wide range of accessories. The machine was previously installed in a university. You are welcome to inspect the machine under power on site and see its excellent condition for yourself.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: Ncedsvivmyspfx Aqvot >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm Nedpfeu Aftgex Aqvect >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: Njdpfxsvtp Edo Aqvjct A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: good (used), Center height 102 mm Distance between centers 450 mm Leit.- / feed shaft Collets W20 available Speed: about 210 - 3000 U / min Ncedpecug H Sjfx Aqvst reducer gear Left.- Rightrunning 2-Multistage drive L x B x H: approx 1760 x 595 x 1230 mm Weight: 650 Kg Different "Schaublin 102" models in stock!

Condition: good (used), Year of construction: 2000, Weiler Primus VC, year of manufacture 2000, digital readout, center distance 500 mm, max. turning diameter over cross slide 150 mm, spindle speed up to 4,000 rpm, spindle bore 40 mm, spindle drive 1.5 kW, Multifix toolholder, 24 longitudinal feeds, metric threads, imperial threads. Njdeyh Hkhjpfx Aqvect

Condition: excellent (used), functionality: fully functional, EMCO Maximat Super 11 – Precision Lathe in Very Good Condition For sale is a used EMCO Maximat Super 11, a robust and precise universal lathe "Made in Austria." This machine is ideally suited for workshops, training centers, or demanding hobbyists who value quality and accuracy. The machine is pre-owned but well-maintained and fully operational. All gear shifts are smooth, the guides are in good condition, and the machine has been regularly serviced. Technical Specifications: Center height: 140 mm Distance between centers: 600 mm Spindle speed range: 55 – 2200 rpm (8 geared steps) Tailstock: MT2 taper Tool holder: Quick-change toolpost Njdexqx Nvepfx Aqvsct Lighting: Integrated LED work light Weight: approx. 360 kg Dimensions (L × H × W): approx. 1.3 m × 1.2 m × 0.6 m Condition & Accessories: Machine runs quietly with low vibration Tailstock is smooth and easy to adjust with high precision Quick-change toolpost included LED work light for optimal visibility Various clamping devices or tools can be purchased additionally upon request (by arrangement) Price: The price is within a reasonable range and negotiable. Open for price discussions upon serious interest. Miscellaneous: Collection preferred, viewing by appointment possible Machine can be shown under power