Condition: used, Year of construction: 2016, Makino A51NX in very good condition, including a new ATC tool changer and Cubes. Approx. 11,000 hours of cutting time. Capacity & Travels: Pallet Size: 400 × 400 mm Nwjdpfozg N E Hex Aiqji X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Workpiece: ∅ 630 mm × 900 mm Max. Payload Capacity: 400 kg Spindle: Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Motion & Feed Rates: Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cutting Feedrate: 50,000 mm/min Axis Acceleration: 1G B-Axis Indexing: Full 4th axis, Direct Drive (0.001-degree increments) Tooling: ATC (Automatic Tool Changer) Capacity: 60 tools Tool-to-Tool Time: 0.9 seconds Max. Tool Diameter / Weight: 170 mm / 12 kg 04003 HSK-A63 Spindle – Replaces the standard ISO50 interface. Features a double taper, full face contact, and hollow shank interface. Tool clamping force is higher than 44kN; HSK tool holders are required. 14017 HSK holders for 60 Tool ATC 26001 Moire Scale Feedback X, Y, Z-Axis Increments 0.05µm, positioning tolerance Tp = 0.006mm (ISO 230-2). 29006 Through Spindle Coolant 3.0MPa – Provides TSC flow of 30 l/min at 3.0MPa, replacing the standard 1.5MPa. Air through the spindle is possible. The pressure data refers to the output flange of the pump. 29009 Flow Switch for Through Spindle Coolant – Monitors through-spindle coolant flow. The machine will feed hold if the flow is below a preset level. Note: Recommended option for filtration systems to prevent tool damage. 31002 Air curtain for splash guard window – Located in the middle of the operator-side window, this air curtain prevents chips and coolant from obstructing the view. 37000 Broken tool sensor outside machining area (BTS) – Tool breakage detection for centric tools (tool diameter 1-40mm, tool length 65 - 430mm). Length measurement is performed using a movable probe. The measurement takes place in the ready position for a tool change, outside the machining area. Accuracy ± 2mm. If there is a difference between the measurement before and after machining, an alarm is triggered automatically. 37101L Automatic Workpiece Measuring Device (RENISHAW OMP60) – Three-coordinate measuring probe from RENISHAW with automatic coordinate correction. The signal is transmitted via infrared. Tolerance approx. 0.005mm. 14 automatic measurement cycles are available as pre-programmed cycles in the program memory. Note: requires 13m. Control Options: 60001 Automatic Corner Override (G62) – Automatically decelerates the cutter at a corner depending on the corner angle, in order to maintain the cutting rate per unit time. 62007 Run hour and parts quantity display. 63034 DATA CENTER Storage Type B (total: 800MB) – Communication card with internal 800MB removable flash RAM card used for storing and executing NC data (of subprograms) for high-speed, high-definition finishing and supporting SGI capabilities. CNC programs can be transferred to and from a CAD/CAM system from the operator's pendant by FTP get and put commands over an Ethernet cable. 66003 Additional 48 Work Offsets (G54.1 P1-P48) – Allows for 48 work coordinate systems, simplifying multiple part fixtures. 68010 600 Macro Common Variables – Variable numbers 100-199 are reset and cleared when the power is turned off, while 500-999 are permanent. Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Payload Capacity: 400 kg Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cut...

Condition: excellent (used), Year of construction: 2015, operating hours: 36,000 h, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,000 mm, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 50 m/min, controller model: Sinumerik 840Dsl, input voltage: 400 V, type of input current: AC, Equipment: chip conveyor, rotational speed infinitely variable, 2x Heller H6000 + Fastems Container Automation Horizontal machining centers with flexible pallet container Heller H6000 2 machines with identical equipment Travel ranges Feed force X 1000mm 15kN Y 1000mm 15kN Z 1000mm 20kN B 360°, 0.001° Direct path measuring system in all axes Rapid traverse: Axis dynamics Power X/Y/Z 50 m/min, 5m/s² B 25 rpm Spindle – Power Cutting Interface: HSK100 Speed: 5-8000 rpm Power: 43kW (40%ED) Torque: 822Nm (40%ED) Nodpfx Aiexxx Dceqswi Last spindle replacement 2020 Tool magazine Type: Rack magazine Magazine slots: 265 max. tool length: 600mm max. diameter: 280mm Tool coding: Balluf chip Second control panel at the setup station Setup station with 7 transfer locations Pallet changing device Pallets: 630x630 max. working envelope: 1000mm max. height: 1200mm max. weight: 1000kg Coolant system: Scraper-type chip conveyor Knoll coolant system Paper band filter IKZ 50 bar, frequency converter controlled Work area flushing Emulsion mist extraction Wiper system for operator doors Additional equipment: Probing device (indexing axis/U-axis) 4 probing heads per machine Tangential control incl. NC cycles Wireless measuring probe (Renishaw) Footprint: 7100x3750x4300mm (L/W/H) Machine weight: 15600kg Total power consumption: 44kVA Control: Sinumerik 840D sl Fast drill break detection Process-integrated tool monitoring Status lamps 3D data for work area model Operating data acquisition (OPC/UA) Year of construction: 2015 Operating hours: approx. 36,000h Fastems Pallet Automation FPC1500 Base container with 2 setup stations Extension container Total 20 pallet positions on 2 levels Control: MMS Footprint: approx. 18x2.4x4.2m Total footprint of the system (2x Heller + Fastems) approx. 18x10x4.5m Machines are still in operation. Inspection possible by arrangement. Transportation of the machines can be organized.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, travel distance X-axis: 560 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 625 mm, Machine type: Horizontal machining center Manufacturer: OKUMA Type: MA-400HA Year of manufacture: 2008 Control system: OSP P200M Country of origin: Japan Delivery time: short-term, by arrangement 4-axis machining center, high productivity, including various accessories Machine equipment: - ConSep chip conveyor system with high-pressure pump - Various software packages - Touchsetter with length measurement and breakage detection - Work area shower Technical details: - Travels - Axes X-axis (column right-left) mm 560 Njdpfozm U Ndsx Aiqswi Z-axis (table forward-backward) mm 625 Y-axis (spindle up-down) mm 610 B-axis 1° 0 - 360° - Number of pallets: 2 (pallet changer for 2 pallets) - Pallet size (mm): 400 x 400 - Max. pallet load capacity (kg): 400 - Max. pallet workpiece dimensions (mm): 500/600 x 710 - Spindle speed (rpm): 15,000 - Main spindle (10min/cont): 22/18.5 kW - Tool holder: BT40 - Tool magazine: 60 positions Optional: - Transport organization and execution - Machine delivery and installation - Machine commissioning

Condition: excellent (used), Year of construction: 2014, machine/vehicle number: 506093, ITALMAC Pegaso 5 Axis Centar Nsdpfx Aiotrvmvjqewi

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Number of controlled axes: 5 X-axis travel (longitudinal): 6650 mm Y-axis travel (transverse): 800 mm Z-axis travel (vertical): 525 mm B-axis rotation (vertical-horizontal): 0° to 90°, continuous C-axis rotation (perpendicular to the work plane): 0° to 360° Electric spindle power at 24,000 rpm: 7 kW Number of independent work areas: 2 Tool holder taper: HSK-E 40 Tool magazine capacity: 9 + 1 Maximum dimensions of disc cutter: diameter/thickness: 300 / 5 mm Automatic positioning of vices Njdpfx Ajzgbb Tsiqewi

Condition: used, Year of construction: 2004, machine/vehicle number: IntNr231232, Hermle C600 U, year of manufacture 2004 Spindle new, with commissioning report Control system: - Heidenhain iTNC 530 - Control system operating hours: 68026 - Machine operating hours: 81237 - Spindle operating hours: 12429 Spindle: - Speed: 16,000 rpm - Tool holder: SK-40 - 30 tool magazine positions Equipment: - Rigid clamping table - NC rotary table, 4th axis (iTNC) - Coolant system - Chip conveyor: none - Electronic handwheel (iTNC) - Tool breakage monitoring - Chip flushing nozzle - Foot switch for clamping/unclamping - Hydraulic unit for clamping/unclamping Travel paths: - X-axis (longitudinal): 600 mm Njdpfx Aiezhv Scjqowi - Y-axis (transverse): 450 mm - Z-axis (vertical): 450 mm Table: - Clamping area: 800 mm x 465 mm - Maximum table load: 250 kg Axes: - Axis rapid traverse: 35 m/min - Acceleration: 5 m/s² - Measuring system X/Y/Z: 0.1 µm Dimensions & Weight: - Machine weight: approx. 6.8 t - Machine dimensions (W x D x H): 2.5 m x 2.4 m x 2.43 m The machine can be inspected under power by appointment. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: ready for operation (used), Year of construction: 2013, travel distance X-axis: 600 mm, travel distance Y-axis: 525 mm, travel distance Z-axis: 400 mm, controller manufacturer: SIEMENS, controller model: SINUMERIK 840D sl, total height: 3,300 mm, overall weight: 12,500 kg, spindle speed (max.): 6,000 rpm, spindle motor power: 6,000 W, This 4-axis SW BX 621 horizontal machining center was manufactured in 2013. It features a robust SINUMERIK 840D sl CNC control system and dual liquid-cooled motorized spindles, each offering up to 6,000 rpm and 26 kW power. The machine supports a maximum tool diameter of 115mm and a tool length of 300mm, with a rapid traverse speed of up to 60 m/min. Ideal for precision machining, the SW BX 621 machine we have for sale. Contact us for more information. Additional equipment • Liquid-cooled motorised spindle in AC synchronous technology Machine Benefits Technical Machine Benefits • Swivelling table (a-axis): direct-driven, horizontal nc rotary table with counter bearing • Max. Fixture / workpiece dimensions: Ø 630 mm x 1420 mm Njdjzh Uqdspfx Aiqowi • Max. Fixture / workpiece weight: 600 kgmax. Fixture / workpiece weight: 600 kgmax. Fixture / workpiece weight: 600 kg • Spindle arrangement: horizontal, side by side • Spindle distance: 600 mm Extra Information Machine still under power Dimensions Machine Depth 5800 mm

Condition: used, Year of construction: 1998, Horizontal CNC Center REALMECA C300H Travel X: 320 mm Travel Y: 350 mm Travel Z: 250 mm Numerical Command: NUM 1060 Série II Cone: BT 40 Spindle rotation: from 100 à 6000 RPM Year of construction: 10/98 Maxi distance spindle nose/table: maxi 450 mm / mini 50 mm Tools store: 20 tools Threadings: Fast: maxi 10 m/min Work: 0 to 10 m/min Axe B: 10 RPM Equipped with: 2 palets 300 x 300 mm Voltage: 380 V Dimensions (L x W x H): 2450 x 1700 x 2400 mm Njdpozm Sqljfx Aiqewi Weight: 3,8 T

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, travel distance X-axis: 610 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 610 mm, rapid traverse X-axis: 60 m/min, rapid traverse Y-axis: 60 m/min, rapid traverse Z-axis: 60 m/min, controller model: Fanuc 16iMB, workpiece height (max.): 745 mm, workpiece diameter (max.): 630 mm, workpiece weight (max.): 400 kg, table load: 400 kg, overall weight: 10,000 kg, spindle speed (max.): 20,000 rpm, number of slots in tool magazine: 50, tool weight: 10,000 g, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Specification Value Machine Type 4-Axis Horizontal Machining Center Pallet Size 400 x 400 mm Number of Pallets 2 (Automatic Pallet Changer) Nwedpfsy Uvhgox Aiqoi Table Load Capacity 400 kg X-Axis Travel 610 mm Y-Axis Travel 610 mm Z-Axis Travel 610 mm B-Axis 0.001° Indexing Spindle Speed 20,000 rpm Spindle Taper SK40 Gearbox Yes Spindle Motor Power Approx. 22 kW Rapid Traverse Rate 60 m/min Tool Magazine Capacity 50 Tools Tool-to-Tool Time Approx. 1.3 sec Maximum Tool Weight 10 kg Coolant Through Spindle Yes Chip Conveyor Included Machine Weight Approx. 10,000 kg Kitamura Mycenter HX400iSII horizontal machining center in very good technical condition. Machine equipped with high-speed 20,000 rpm spindle, gearbox, automatic pallet changer (2 pallets), chip conveyor, through-spindle coolant and FANUC 16i-MB control system. Suitable for high-precision and high-speed machining applications.

Condition: good (used), Year of construction: 2003, functionality: fully functional, travel distance X-axis: 870 mm, travel distance Y-axis: 710 mm, travel distance Z-axis: 660 mm, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 50 m/min, controller model: Fanuc 16iMB, workpiece height (max.): 1,100 mm, workpiece diameter (max.): 800 mm, workpiece weight (max.): 600 kg, spindle speed (max.): 15,000 rpm, number of slots in tool magazine: 50, Equipment: chip conveyor, rotational speed infinitely variable, Specification Value Machine Type 4-Axis Horizontal Machining Center Pallet Size 500 x 500 mm Number of Pallets 2 (Automatic Pallet Changer) Table Load Capacity 800 kg X-Axis Travel 870 mm Y-Axis Travel 710 mm Z-Axis Travel 660 mm B-Axis 0.001° Indexing Spindle Speed 15,000 rpm Spindle Taper SK40 Gearbox Yes Spindle Type Gear Driven Spindle Motor Power Approx. 26 kW Rapid Traverse Rate 50 m/min Tool Magazine Capacity 50 Tools Tool-to-Tool Time Approx. 1.5 sec Maximum Tool Weight 20 kg Through Spindle Coolant Yes Chip Conveyor Included Machine Weight Approx. 20,000 kg Njdpfx Aiey Uvlfoqswi Kitamura HX500i Alpha horizontal machining center in very good technical condition. Machine equipped with 15,000 rpm gearbox spindle, SK40 spindle taper, automatic pallet changer (2 pallets), chip conveyor, through-spindle coolant system and FANUC 16i-MB CNC control. Suitable for precision machining and demanding production applications.

Condition: ready for operation (used), Year of construction: 2014, operating hours: 19,865 h, travel distance X-axis: 1,050 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: FANUC, controller model: Series 31i-model B, total height: 3,422 mm, total width: 7,297 mm, table load: 1,500 kg, overall weight: 18,000 kg, spindle speed (max.): 10,000 rpm, number of slots in tool magazine: 40, tool weight: 30,000 g, product length (max.): 3,780 mm, number of axes: 4, This 4-axis DOOSAN NHP6300 was manufactured in 2014. It features an impressive X-axis travel of 1,050 mm, Y-axis travel of 900 mm, and Z-axis travel of 1,000 mm. The machine includes a maximum pallet load of 1,500 kg and a tool capacity of 40 tools. If you are looking to get high-quality machining capabilities, consider the DOOSAN NHP6300 horizontal machining centre we have for sale. Contact us for further details. • Distance from top of pallet to spindle center: 100–1,100 mm • Distance from pallet center to spindle nose: 75–975 mm • Pallet • Type: Indexing (rotary) • Indexing angle: 1° • Size: 630 × 630 mm • Maximum load: 1,500 kg • Mounting pattern: 24 × M16 × P2.0 {5–18H8} • Maximum workpiece size (Ø × H): Ø1,050 × 1,350 mm • Spindle • Speed: 10,000 rpm (options: 6,000 / 15,000 rpm) • Taper: ISO 50 (7/24 taper) • Maximum torque: 489 Nm (options: 599.8 / 350 Nm) • Feed rates • Rapid traverse (X/Y/Z): 60 / 60 / 60 m/min • Maximum cutting feed: 30,000 mm/min • Automatic Pallet Changer (APC) • Number of pallets: 2 • Type: Rotary shuttle • Change time: 12 s • Drive: Servo motor • Automatic Tool Changer (ATC) • Tool interface: BT / CT / DIN (HSK optional) • Magazine type: Chain • Standard capacity: 40 tools (options: 60 / 90 / 120 / 150) • Matrix magazine capacity: 196 / 256 / 316 / 376 tools • Maximum tool diameter: Ø130 mm (Ø125 mm per note) • Maximum tool diameter with adjacent pockets empty: Ø320 mm • Maximum tool length: 630 mm (HSK: 700 mm) • Tool-to-tool change time: 2.0 / 3.5 s • Chip-to-chip change time: 5.0 / 6.5 s • Motor power and utilities • Spindle motor: 25 / 30 kW (options: 22 / 30, 50 / 55 kW) • Compressed air supply: 0.54 MPa • Tank capacities • Coolant: 925 l • Lubrication: 7.2 l Additional equipment • Fastems automation system Technical Specification Taper Size ISO 50 Nwsdpfx Aiezh Hpfeqsi

Condition: excellent (used), Year of construction: 2007, BA 600-2 CNC, Horizontal Milling and Drilling Center SW Schwäbische Werkzeugmaschinen GmbH Travel: X axis: 600 mm Y axis (changeover position): 600 (975) mm Z axis: 500 mm Control: Siemens 840D control, side-mounted Feed/Rapid traverse speeds: X, Y, Z: 1 – 45,000 mm/min Max. feed force X, Y, Z: 15,000 N Average acceleration: X, Y, Z: 2.5 m/s² Measuring system: Direct measuring system X, Y, Z Spindles: Spindle speed (infinitely variable): 20–10,000 rpm Torque: 2 x 363 Nm (S6/40% duty cycle) Power: 2 x 38 kW (S6/40% duty cycle) HSK-A 100, horizontal tandem arrangement Spindle distance: 600 mm Spindle bearing diameter: 100 mm Motor spindles, liquid-cooled, AC technology Working area: Swing carrier with spur gearing, max. workpiece weight 2,000 kg Swivel time 0/180 degrees approx. 6.0 sec 2 NC rotary tables, hydraulically clamped, max. workpiece weight 700 kg, table speed 25 rpm Partition between machining and loading area Tool magazine: 2 x 50 tools HSK-A 100 chain-type magazine Tool change time (chip-to-chip): 4.48 sec Max. tool diameter: 100 mm 250 mm with adjacent slot free Max. tool length: 420 mm Max. tool weight: 20 kg Equipment: Central lubrication Oil minimum quantity lubrication (spindle lubrication) Chip conveyor (hinged belt conveyor) Coolant purification with compact band filter Hydraulic unit Maintenance unit Water recooler Full enclosure, crane loading possible Dimensions: approx. 5.15 x 8.50 x 4.20 m Weight: approx. 20,000 kg Year of manufacture: 2007 Other features: Very good condition Setup parallel to main time Available from December 2023/January 2024 Njdpfx Aezhlfroiqswi

Year of construction: 2017, condition: used, Setup station, pallet changing system, pallet changer, pallet storage, tool changer chain, chain magazine, tool changing system, tool magazine Njdpfxoflk Hps Aiqewi -Setup station with: Garant ZERO CLAMP G-11886 -Manufacturer no.: 101545300002672 - 21063 1721559 -Dimensions: 400/400/H810 mm -Weight: 232 kg

Condition: used, Tool changer chain, chain magazine, tool changing system, tool magazine -Manufacturer: Seco, tool changing system tool arm -Drive unit: TP type MRC-S28-1V-210 -Dimensions: 780/420 / H300 mm Njdpfjg U A I Hox Aiqjwi -Weight: 66 kg

Condition: used, Axis control, electronic handwheel, control unit Nedpfx Aiodwc I Ssqewi -The electronic handwheel was removed from a CNC machining center make: Hitachi Seiki type: HC400. Other spare parts available. -electronic handwheel for Hitachi Seiki type: HC400 -Dimensions: 170/120/H80 mm -Weight: 0.6 kg

Condition: used, Tool changer chain, chain magazine, tool changing system, tool magazine -Spare part comes: from a machining center BJM type ALBZ-145 -Tool change system -CUT changer -RIG changer: RIG 06-12-P003 VX VCP Nwsdpfx Ajfcr Nboiqei -Drive motors: MGM -Dimensions: 1400/950/H830 mm -Weight: 380 kg

Condition: good (used), Tool changer chain, chain magazine, tool changing system, tool magazine -comes from a MAHO CNC machining center, type: MC 600 -for: max. 48 recordings -Recording: SK40 -Dimensions: 1630/H450 mm -Empty weight: 325 kg Nwjdsb A Nu Tepfx Aiqei

Condition: good (used), Tool changer chain, chain magazine, tool changing system, tool magazine -Manufacturer: Mikron, tool changer from CNC machining center Mikron UME 600 -for: max. 22 shots Nwedpsrb E E Njfx Aiqoi -Intake: SK40 -Dimensions: 1200/1150/H860 mm -Transport weight: 294 kg

Condition: good (used), Tool changer chain, chain magazine, tool changing system, tool magazine -for: max. 60 recordings -Hole: Ø 17 mm Nodpfx Aeb A Rzmoiqewi -Weight: 44 kg

Condition: used, Tool changer chain, chain magazine, tool changing system, tool magazine -Manufacturer: MAHO, Tool changer from CNC machining center MAHO MH 800C -for: max. 24 shots -Recording: SK Nwodpfx Aijq Tvp Uoqei -Dimensions: 1200/410/H480 mm -Town weight: 106 kg

Condition: good (used), Tool changer chain, chain magazine, tool changing system, tool magazine -The tool changer comes from CNC machining center make: Hitachi Seiki type: HC400 -Tool changer for: Hitachi Seiki type HC400, other spare parts available. -complete with: gripper arm and drive Nwedpfxjdtcrqs Aiqji -Tool changing positions: 80 -Intake: SK40 -Dimensions: 2270/630/H1725 mm -Weight: 860 kg

Condition: good (used), Tool changer chain, chain magazine, tool changing system, tool magazine -Manufacturer: Mikron, tool changer from CNC machining center Mikron VC500D -for: max. 16 recordings -Recording: SK40 -Individual components: see photos -Transport dimensions: Ø 780 x 540 mm -Weight: 56 kg Nsdpfsy Tvttex Aiqswi

Condition: good (used), Tool changer chain, chain magazine, tool changing system, tool magazine -Spare part comes from a BJM machining center type ALBZ-145 -Intake: HSK40 -Tool changing system: CTM42 DO 12P3 400 -CUT changer: CUT42-V-90-60-D VX -RIG changer: RIG 06-12-P003 VX VCP IN DA -Drive engines: MGM -Dimensions: 730/700/H450 mm Nwodpfx Aiefcr I Esqji -Weight: 160kg

Condition: good (used), Year of construction: 2011, Ref. -No.: 10598 Manufacturer: HELLER Type: MC 2000 Year of construction: 2011 Type of control: CNC-Steuerung Control: Siemens 840 D sl Storage location: Halberstadt Country of origin: Hermany Machine-No.: 50XXXX X-Travel: 800 mm Y-Travel: 800 mm Z-Travel: 1000 mm Nedpfx Asx Hn D Reiqewi Work spindle torque (25% ED): 242 Nm Tool Taper: SK 40 Numbers Of Tools In Magazin: 54 Tool Piece Magazine With: 80 Pcs./pcs. Turning Speeds: 10000 RPM Drive Capacity - Spindle Motor: 17 kW High-Pressure Pump: 50 bar Speed range - main spindle: 10000 RPM Numbers Of Pallets: 2 Size Of Pallet: 630 x 500 mm Weight Of The Machine Ca.: 13000 t spindle running time: 7000 H Operating hours: 14000 H Preparation area: 4 x 90° hydraulic pressure: 200 bar Further information: - The machine has been measured - The geometry is in excellent condition - The spindle runs a little rough - Clamping towers and cutting tool holders are also included - 2 additional clamping towers - 2 replacement pallets - 2-axis servo tool changer - Scraper conveyor for dry machining - Cold light in the work area - Central cooling unit for motor spindle and control cabinet - Control unit at the workpiece setup station - NC-controlled rotary table - Clamping hydraulics The machine can be viewed under power by appointment.

Condition: good (used), Year of construction: 2017, Ref. -No.: 10596 Manufacturer: HELLER Type: H - 2000 Year of construction: 2017 Type of control: CNC-Steuerung Control: Siemens 840 D Storage location: Halberstadt Country of origin: Germany Machine-No.: 56XXX X-Travel: 630 mm Y-Travel: 630 mm Z-Travel: 630 mm B-Axis: 0,001 ° Table Load: 500 kg Max. Tool Length: 350 mm Max. Tool Diameter: 160 mm Tool Taper: HSK 63 Numbers Of Tools In Magazin: 80 Turning Speeds: 16000 RPM Tool changer: Doppelgreifer Max. Workpiece height: 850 mm Max. Torque: 95 Nm Rapid Travel X/Y/Z: 60 mm / min Rapid Traverse X-Axis: 80 m / min Rapid Travel Y-Axis: 80 m / min Rapid Traverse Z-Axis: 90 m / min Drive Capacity - Spindle Motor: 40 kW Internal cooling: 50 bar Numbers Of Pallets: 2 Size Of Pallet: 400 x 500 mm spindle running time: 1000 H Operating hours: 3000 H Workpiece interference circuit max.: 720 mm Media interface: 5 - fach Nwsdex Hn D Djpfx Aiqoi Further information: - Equipped with NC rotary table. - State-of-the-art spindle technology. - Ideal for precise machining tasks. - Spindle hours: 1000. - Pallet can be rotated manually 4 x 90 - Hydraulic pressure 200 bar - Quick drill breakage check Machine can be viewed under power by arrangement