Condition: used, Year of construction: 2012, travel distance X-axis: 600 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, Travel: X / Y / Z = 600 / 500 / 500 mm NC rotary table 600 x 500 mm B-axis swivel range -5° to +110° C-axis 360° Maximum loading weight: 400 kg, direct measuring systems including table cooling Rjdpfx Adoyc Tthebobt Dynamics package: linear drive on X / Y axes Rapid traverse X / Y / Z: 80 m/min Acceleration X / Y / Z: 10 m/s² Active cooler for main spindle, linear drive, and table Control: Siemens 840D SL Operate Spindle: 20 - 24,000 rpm HSK-A63 according to DIN 69893 • Tool magazine: chain magazine with 60 tool stations • Tool length measurement and breakage control: Blum Z-Nano • Scraper belt chip conveyor with cleaned slotted sieve, internal coolant supply (IKZ) paper filter 40 bar 231 l/min, 600 l tank including rotary viewing window, sealing air for linear systems, bed flushing • Blowing air through spindle center selectable via M function, maintained air with low oil content • Electronic handwheel • Spray gun for chip flushing • Extended chip flushing system • Laminated safety glass panels for working area door and side window • Operating mode 4 • High speed settings • Measuring probe: Blum HSK-A63 • Prepared for 3D QuickSet • Optionally oil mist extraction unit • New spindle at 25,800 spindle hours

Condition: used, functionality: fully functional, 5-axis Spindle 18,000 rpm Tool magazine with 32 positions Rsdpfx Aeyc Tq Hjdbsbt Tool holder SK40 Spindle hours: 15,389 Zeroclamp 12 pots 138 (zero-point clamping system) Components: Machine with NC rotary table and pick-up magazine Chip conveyor Coolant/lubricant unit 250L Belt filter system 600L Oil/emulsion mist separator

Condition: used, DMU60: 5-axis, spindle 18,000 rpm, tool magazine with 24 slots, tool holder SK40, spindle hours: 15,305, Zeroclamp 6 pots 138 (zero-point clamping system). Rjdeyc Tmbepfx Adbobt

Condition: excellent (used), Year of construction: 2016, With B + C axis Working travels 762 x 508 x 508 mm Table diameter 500 mm Spindle taper 40 Spindle speeds -12'000 rpm Tool changer 40 Pos. Control HAAS Rbsdpfxslhqyds Adbst Coolant through spindle Misc.accessories MARCELS MASCHINEN CH

Condition: used, Year of construction: 2018, functionality: fully functional, overall weight: 1,400 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 2,200 W, number of spindles: 1, number of slots in tool magazine: 5, input voltage: 400 V, type of input current: three-phase, Equipment: documentation/manual, rotational speed infinitely variable, We offer a used CNC machining centre for aluminium and plastic profiles, Fom Industrie Adir-C, year of manufacture 2018. Swivel table -90°/0°/+90°, 4x pneumatic clamps, machine operated in single-shift mode. Rbsdpfx Aeycg H Usdbet If you have any questions or require further information, please do not hesitate to send us a message or contact us by phone.

Condition: good (used), Year of construction: 2007, functionality: fully functional, travel distance X-axis: 450 mm, travel distance Y-axis: 270 mm, travel distance Z-axis: 310 mm, rapid traverse X-axis: 75 m/min, rapid traverse Y-axis: 75 m/min, rapid traverse Z-axis: 75 m/min, nominal power (apparent): 17 kVA, total height: 2,300 mm, total length: 1,500 mm, total width: 2,600 mm, overall weight: 3,400 kg, spindle speed (max.): 30,000 rpm, spindle nose: HSK40, number of slots in tool magazine: 40, input voltage: 400 V, type of input current: three-phase, CNC machining center CHIRON FZ08 KS Magnum High Speed Plus (HSP) TECHNICAL CHARACTERISTICS: Year of manufacturing: 2007 CNC control : FANUC 18i-MB5 Number of axes : 7 Stroke X axis : 450 [mm] Stroke Y axis : 270 [mm] Stroke Z axis : 310 [mm] Traversing feeds X, Y and Z axes : 75000 [mm/min] Max. bar diameter in turning spindle : 32 [mm] Main spindle max. speed : 8000 [rpm] Main spindle max. power : 12 [kW] Angular A axis stroke : 360 [°] A axis indexing precision : 0.001 [°] B axis swivelling stroke : -20° / +115 [°] B axis indexing precision : 0.001 [°] Spindle type : HSK40 Max. spindle speed : 30000 [rpm] Tool changer magazin number of stations : 40 Part turnaround by robot (6th side machining) : Yes RS232 Interface : Yes Total power required : 17 [kVA] Supply voltage : 400 [V] Rbjdpfex U U Hbsx Adbjt Dimensions : 1500 x 2600 x 2300 [mm] Weight : 3400 [Kg] More information available upon request.

Condition: good (used), Year of construction: 1998, AXA VHC-3-M/K 5-Axis Universal Machining Center Rsdpfsyddahsx Adbebt Year of manufacture: 1998 Control: SIEMENS 840C Machine number: 85667 Travel distances: Longitudinal X-axis: 1,200 mm Transverse Y-axis: 700 mm Vertical Z-axis: 800 mm B-axis: -90° to +90° C-axis: 360,000° Spindle repair valued at €15,000 carried out in 08/2025. Equipment: Swivel head -90 degrees to +90 degrees, 2.5 degree indexing NC rotary table, SEMPUCO brand, 400 mm Speed range: 40 to 6,000 rpm / 17.2 kW 22-position tool changer Internal coolant supply through the spindle External coolant supply Paper band filter Chip conveyor Included in delivery: Documentation / machine parameters on data storage device Equipment, technical data, and transport – see PDF. Illustrations, contents and stated specifications are supplied without guarantee and are therefore non-binding. All other accessories visible in the photos and video are not included and therefore not part of this sale. The delivery scope only includes those accessories which are explicitly listed here, in the order confirmation, and in the invoice. FCA (Free Carrier Loaded Truck) D-92729 Weiherhammer Packaging only Delivery time: immediate Subject to prior sale / payment due immediately upon purchase

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, Equipment: chip conveyor, documentation/manual, Deckel Maho DMU 50 evo Linear with TNC 530 control from Heidenhain, TOP condition Technical data: >> Year of manufacture 2006 >> Manufacturer Heidenhain, type iTNC 530 >> Travel paths X500/Y450/Z400 >> C-axis 360 degrees >> B-axis 0 degrees to 161.955 degrees >> Tool holder HSK A63 >> Max. spindle speed up to 18000 rpm >> Feed continuously programmable up to X, Y, Z 20000 mm/min C-B axis continuously programmable up to rapid traverse speed >> Rapid traverse Y- Z axis 50 m/min X-axis 80 m/min (linear drive) B-axis 40 rpm C-axis 50 rpm >> Tool magazine: Double gripper 60 magazine spaces >> Table clamping area Ø 500 x 380 mm T-slot spacing 63/14H7 >> Table load 200 KG Rodpfx Ajvyr Tdsdbjbt >> Dimensions and weight: approx. Machine without control and attachments Depth 3.0 meters Width 2.4 meters Height 2.6 meters Weight approx. 7000 kg >> Operating voltage 400 V >> electr. Handwheel Heidenhain HR 410 >> Power connection 17 KVA >> Chip conveyor >> Active spindle cooling >> Mist extraction >> IKZ 40 bar >> Coolant lubricant cleaning system (fleece filter system) >> Spray gun >> Visiport >> Sealing air on the measuring system >> Preparation for robot loading >> 3D probe Heidenhain TS640 >> 3D Quick Set >> Kinematics >> Blum laser for tool measurement and breakage control Cpvnunmsoi >> Complete documentation Dn2F2R The following work was carried out: >> Generally overhauled main work spindle >> Complete maintenance: All cooling hoses and pneumatic hoses replaced, new filters, fluids and belts replaced. Scrapers, etc. Complete cleaning. >> Geometrically measured (acceptance protocol) About the machine: A Deckel Maho DMU 50 evo Linear machining center with a TNC 530 3D path control from Heidenhain is offered. The machine is in very good condition. The main spindle on the DMU was overhauled (replacement spindle), completely serviced and an acceptance protocol was created. Take advantage of the opportunity to view and try out the machine on site with power on.

Condition: used, Year of construction: 2003, x-travel 1.600 mm y-travel 1.250 mm z-travel 1.000 mm size of pallet 1.000 x 1.250 mm control SIN840D power capacity at 40 % load 38,00 KW spindle turning speed - stepless 20 - 10.000 U/min power capacity at 100 % load 25,00 kW max. torque at 40% / 100% load 288 / 187 Nm tool taper SK50 feed X/Y/Z/-axis 20 - 15.000 mm/min rapid traverse X/Y/Z 60,00 m/min B - axis -150° / +80° x 0,001 ° feed B-axis 3.600 ° / min C-axis 360 x 0,001 ° Rapid motion C- axis 1 - 3.600 U / min. table load 3.000 Kg tool magacine with 240 tool diameter 110 mm wotkpiece diameter with 2 vacant positions 250 mm tool length - max. 650 mm weight of tools max. 15,00 kg total power requirement 75,00 kW weight of the machine ca. 55,00 t dimensions of the machine ca. 12,50 x 8,00 x 4,20 m 5-axis machining center with SIEMENS Sinumerik 840D control Rbedeydflrjpfx Adbst electronical handwheel operating mode 4 240-position tool magazine 4-position pallet storage system TS641 measuring probe BLUM laser coolant system coolant through the spindle chip conveyor coolant cooling

Condition: good (used), Year of construction: 2010, Ref. -No.: 10287 Manufacturer: DMG Type: DMC 210 FD Year of construction: 2010 Type of control: CNC Control: Heidenhain Mill Plus Storage location: Halberstadt Country of origin: Deutschland Rodoxxn Ukopfx Adbsbt X-Travel: 2100 mm Y-Travel: 2100 mm Z-Travel: 1250 mm Machine length: 11.000 mm Machine width: 5.000 mm Machine Height: 3.500 mm Max. Workpiece diameter: 2500 mm Max. Workpiece Weight: 6.000 kg Max. rotary table diameter: 1.850 O Table speed range: 250 min/-1 Tool Taper: HSK-A100 Tool Piece Magazine With: 183 Pcs./pcs. Spindle Speed: 12.000 RPM Max. Torque On The Boring Spindle: 288 Nm Max. Torque: 2.000 Nm Feed Speeds X/Y/Z Axis: 30.000 mm / min Max. Workpiece height: 1.460 mm axes: 5 Further information: Turning and milling center incl. pallet changing system Gear spindle Coolant treatment system, with belt filter, 710 x 50mm 1 Knoll 600S2 chip conveyor 2 Losma oil mist extraction units 1 steel platform (storage space for clamping device): 5,300 x 2,900 mm - Axes renewed 11.2024 - New encoder, electrical components renewed - Geometry protocols available Machine is still in production and under power. The machine can be viewed at any time by appointment.

Condition: excellent (used), Year of construction: 2021, operating hours: 7,237 h, functionality: fully functional, travel distance X-axis: 550 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 510 mm, torque: 64 Nm, controller manufacturer: Siemens, table load: 600 kg, rotational speed (max.): 10,000 rpm, overall weight: 5,600 kg, operating hours of spindle: 4,048 h, number of axes: 3, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, The machine is in very good condition and has so far only been used for cutting M8 threads in aluminum. Therefore, the spindle load has also never been particularly high. Equipment: • Renishaw PP40 wireless workpiece probe • Tactile tool measurement system • Job Shop package for Siemens 828 D • Chip conveyor • Tool changer with 24 positions • Tool holder for SK 40 DIN69871 and pull stud DIN69872 • Table surface 850x650mm Rjdeyftzqopfx Adbjbt • Drive power 100% duty cycle 9 kW • Drive power 40% duty cycle 13 kW • Torque 43 Nm • Maximum torque 64 Nm • Rapid traverse X / Y / Z 24/24/24 m/min • Coolant spray gun

Condition: ready for operation (used), Year of construction: 2008, operating hours: 41,795 h, functionality: fully functional, travel distance X-axis: 1,760 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 800 mm, controller model: Siemens 840 D ShopMill, rotational speed (max.): 6,000 rpm, The sliding surface of the base carriage X/Y was renewed in 2022! TECHNICAL DETAILS Travel range X-axis: 1,760 mm Travel range Y-axis: 600 mm Travel range Z-axis: 800 mm horizontal Travel range Z-axis: 770 mm vertical A-axis: ±100° Faceplate diameter: 520 mm Rapid traverse X/Y/Z: 40/40/30 m/min Number of controlled axes: 5 Spindle speed range: 30 - 6,000 rpm Drive power: 30 kW Torque: 143 Nm Tool holder: SK 40 Tool stations: 36 MACHINE DETAILS Control: Siemens 840 D ShopMill Dimensions & Weight Required floor space (L x W x H): 5.2 x 3.4 x 3.3 m Rsdeyfriaspfx Adbobt Machine weight: 12,000 kg Operating hours: 41,795 h EQUIPMENT NC rotary table AXA RTA 4L-520 Manual tailstock, center height 280 mm Internal coolant supply (IKZ): 30 bar Chip conveyor, discharge left Integrated coolant tank 200 l Coolant tank 400 l 3D touch probe, Renishaw RMP 60 with RMI receiver Direct linear measurement system Heidenhain Hardened flat guides Counter-guides coated with sliding material (Turcite)

Condition: ready for operation (used), functionality: fully functional, travel distance X-axis: 2,300 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 600 mm, controller model: Siemens Sinumerik 840D, rotational speed (max.): 18,000 rpm, TECHNICAL DETAILS Travel X-axis: 2,300 mm Travel Y-axis: 800 mm Travel Z-axis: 600 mm Spindle speed range: 50 - 18,000 rpm Tool holder: HSK 63 Tool positions: 30 Table size: 1,400 mm x 750 mm (right side) MACHINE DETAILS Control: Siemens Sinumerik 840D Rsdoyfq T Djpfx Adbebt EQUIPMENT NC rotary table 800 (left side) Chip conveyor Internal coolant supply (IKZ)

Condition: good (used), Year of construction: 2005, operating hours: 84,564 h, functionality: fully functional, travel distance X-axis: 500 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, rapid traverse X-axis: 12 m/min, rapid traverse Y-axis: 12 m/min, rapid traverse Z-axis: 12 m/min, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, nominal power (apparent): 17 kVA, controller manufacturer: iTNC 530 Heidenhain, controller model: iTNC 530 Heidenhain, total height: 2,500 mm, total length: 3,000 mm, total width: 3,000 mm, table width: 500 mm, table length: 650 mm, table load: 200 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 10,000 rpm, operating hours of spindle: 22,855 h, spindle motor power: 13,000 W, number of slots in tool magazine: 16, tool length: 300 mm, tool diameter: 130 mm, tool weight: 6 g, Equipment: rotational speed infinitely variable, The machine is in good condition. A few things have been redone and freshened up. The following has been overhauled: -Complete X-axis bearing including ball screw and bearing -Various hydraulic components -Tool changer reset and sensors replaced -New door switch installed -New discs installed (unfortunately already got some flying chips again) -New coolant pump -New screen, as it was defective -New handwheel HR410 The machine does not have many spindle hours or switch-on hours. The machine has never seen a series production and has always been operated sensibly. Warm-up programs etc. We are tool and mold makers, so we tend to do more complex contours rather than heavy machining. I am only selling this because I need a simultaneous machine and also more travel paths. Technical data: Year of manufacture 2005 x-travel 500 mm y-travel 450 mm z-travel 400 mm Control iTNC 530 Heidenhain Main spindle Speed range - main spindle 20 - 10,000 rpm Drive power - main spindle 9 / 13 kW Torque 57 / 82 Nm Tool holder SK 40 Rotary table Table clamping area 630 x 500 mm Swivel range -5 / +110 ° Max. table load 200 kg T-slots 14 H7 T-slots - distance 63 mm Rsdovtnm Hopfx Adbsbt C-axis +/- 360 ° Feeds: Rapid traverse (X / Y / Z) 12 m/min Feed rate 10,000 mm/min Tool changer: Tool positions 16 pos. Max. tool weight 6 kg Max. tool length 300 mm Max. tool diameter 80 mm Max. tool diameter with free adjacent box 130 mm Tool holder SK 40 Total power requirement 17 kVA Machine weight approx. 3.6 t Space requirement approx. 3.0 x 3.0 x 2.5 m Tool milling machine - Universal DECKEL MAHO - DMU 50 Attention: no chip conveyor and no automatic measuring probe! - 5 axes (3+2) - WITHOUT tools Attached are pictures of the machine. The machine was intentionally not cleaned before taking the pictures, so it is in the "chip" and is used daily. You can also see the hours of the machine there. Kinematics and geometry are OK. for our needs, but could possibly be re-measured. We have never had any crashes etc.

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, TECHNICAL DETAILS X-axis: 680 mm Y-axis: 400 mm Z-axis: 625 mm B-axis: +65º to -110º C-axis: 360º Control: Fanuc 16iMB Rbedpfx Ajyfpkusdbet Spindle details Spindle speed: 40 – 15,000 rpm Spindle taper: 7/24 steep taper #40, Big PLUS Spindle diameter: 80 mm Spindle torque: 135 Nm / 850 rpm Spindle power: 15/7.5 kW Feed rates and rapid traverse Rapid traverse X/Y/Z: 30 m/min B-axis: 10 rpm C-axis: 13.5 rpm Feed rate X/Y/Z: 1 - 15 m/min B-axis: 1 - 2,160º/min C-axis: 1 - 3,600º/min Max. tool Ø: 80 mm Max. tool Ø with free adjacent stations: 150 mm Max. tool length: 260 mm Max. tool weight: 8 kg Workpiece dimensions Max. workpiece diameter: 360 mm Max. workpiece height: 250 mm

Condition: ready for operation (used), Year of construction: 2003, Make: DMG / DECKEL MAHO Type of machine: DMC 70 eVolution Year of manufacture: 2003 Control system: MillPlus Tool holder: SK40 x-travel: 700 mm y-travel: 550 mm z-travel: 500 mm Speed range: 12.000 U/min max. Table load: 800 kg Table dimensions: 900 × 550 mm Redjydfbmjpfx Adbjbt

Condition: new, FACTORY-NEW MACHINING CENTER Rbjdpfehy Aunox Adbet HEIDENHAIN TNC 640 CNC control HEIDENHAIN package (motors, measuring systems, and handwheel) X-axis: 3,000 mm Z-axis: 2,000 mm Y-axis (cross beam): 1,300 mm V-axis (column): 1,000 mm Rotary table (C-axis): 2,000 x 2,000 mm Max. workpiece weight: 15,000 kg Automatic universal swivel head 1° x 1° Spindle taper: SK50 DIN 69871/A Spindle speed: 6,000 rpm (oil cooled) Max. spindle motor power: 53 kW ICS – internal coolant supply – 36 bar Rapid traverse X, Y, V & Z: 30,000 mm/min Positioning accuracy: ± 0.015 mm Repeatability: ± 0.010 mm Chain-type tool changer: 60 positions Double hinged belt chip conveyor (longitudinal) Perimetric enclosure (top open) Only inquiries from Germany will receive a response.

Condition: new, Year of construction: 2023, functionality: fully functional, 5-axis travelling column machining centre - SAMAG SFZ3500- with swivel head and internal rotary table (Ø:1000mm, interference Ø:1300mm) X:3500mm Y:1000mm Z:1000mm Spindle: SK50 max. 12,000rpm 54kW Tool changer: 60 Control: Heidenhain TNC7 Rbedsttv Haspfx Adbet Coolant system with paper belt filter Internal coolant supply: 40bar (max. 80bar) Internal air supply through the spindle 3D touch probes Collision monitoring (DCM) Kinematics Opt The machine is available at short notice and can be inspected and tested at the factory.

Condition: ready for operation (used), Year of construction: 2020, operating hours: 8,700 h, Control Unit Brand HEIDENHAIN Model TNC 640 Movement Rodpfxsx D D Svs Adbsbt X-Axis Movement 800 mm Y-Axis Movement 950 mm Z-Axis Movement 1020 mm Additional Equipment Accessories: Additional pallet + coolant cooling unit This 5-axis GROB G550a universal machining centre was manufactured in 2020. It offers advanced capabilities for complex machining tasks. Consider the opportunity to buy this GROB G550a universal machining centre. Contact us for more information. Application Types Milling

Condition: like new (used), Year of construction: 2016, The ONIX 3300 is a CNC machining centre with 3 controlled axes + 1 additional axis, specifically designed for drilling and milling operations on aluminium, PVC, light alloy, and steel profiles with a maximum thickness of up to 3 mm. The machine offers a working capacity of 3300 mm and is equipped with an 8-position automatic tool magazine, with the possibility of housing an angular head for machining on three sides of the profile, as well as a saw blade for end milling operations. The fully enclosed structure contains the electrospindle, which provides a power of 4 kW and a rotation speed of up to 18,000 rpm, ensuring high performance and excellent machining quality. The swivelling control console, positioned on the right-hand side of the machine, allows for easy and intuitive management of programs and controls during every phase of the production cycle. The ONIX 3300 is equipped with CNC control for the axes and an industrial PC for program management, complete with a 17” LCD monitor, 80 GB hard disk, and 2 USB ports. The programming language is ISO standard, with an operator interface based on the Windows XP platform, and dedicated programming software ITALSOFT – FLY CAM CAD-CAM 3D, designed to optimize machining operations and production cycles. Technical Features • Dimensions (LxPxH): 4600x1675x2260 mm - 182x66x89 in • Dimensions for transport (LxPxH): 4500x1250x2300 mm - 177.5x50x91 in • Weight: 1500 kg - 3306 lb • Nominal power: 6 kW • Absorbed power: 16 A • Voltage: 400 V three phase • Frequency: 50/60 Hz • Air pressure: 7 bar • Accuracy: 0.1 mm - 0.004 in • Electrospindle power: S1 4 kW - 0/18000 rpm • Maximum torque: 3.7 Nm at 12000 rpm • Tool holder adapter: ISO 30 • Spindle cooling system: Electric fan • Operation area: 1 • Machinable sides no.: 1 (3 sides with Angle head) • Standard clamps no.: 4 (manual) • Tool magazine: 8 tool places (on board the basement) • Clamping force: 130 kg per clamp • Zero reference point no.: 1 (manual) • Spray nozzles for lubrication: 1 on the electrospindle • Tank capacity: 2.2 litres • Slides greasing: Manual • Operating temperature range: From 10 to 35 °C • Humidity: 75 % • Standard colors: RAL 7032 / RAL 5018 • Chip conveyor system: Chip conveyor plate • Machine safety: Safety light screen • Operator interface Monitor: 17” LCD • USB port: On the control panel • Software: ITALSOFT CAD-CAM Rbjdpfxewb D Sts Adbjt

Condition: used, Year of construction: 2007, High-performance CNC machining centre equipped with a 5-axis electrospindle for advanced machining operations on aluminium, PVC, light alloys, and composite materials. Technical Description: - 5-axis electrospindle – A=+/-125°, 12 kW with cooling unit - Automatic tool changer with 18 positions + Ø400 mm blade, protected and mounted on the gantry sliding along the X-axis Rbsdpfjvgl Rcsx Adbot - Working area – travel: X = 7500 mm; Y = 1500 mm; Z = 620 mm - Milling operations with linear and circular interpolation on the X-Y-Z axes - Machining on 5 faces - PENDULAR operation capability - No. 8 pneumatic clamps with automatic positioning - No. 2 pneumatic reference stops - Tool cooling system with minimal lubrication unit - Motorized conveyor belt for chip and scrap evacuation - CNC, user and maintenance manual, CE certification included

Condition: good (used), Year of construction: 2017, functionality: fully functional, travel distance X-axis: 670 mm, travel distance Y-axis: 830 mm, travel distance Z-axis: 600 mm, Machine advantages Technical advantages of the machine High spindle speeds: 18,000 rpm Comprehensive cooling systems for spindle and axes Rbsdpfoyard Tjx Adbet Advanced measuring systems for precision Extensive tool changer capacity (96 slots HSK-A 63) Network and USB connection Swivel range: -120 to +120 degrees Rotary table: 360 degrees, unlimited rotation

Condition: ready for operation (used), Year of construction: 2005, x-travel 400 mm y-travel 450 mm z-travel 350 mm Control Heidenhein iTNC 530 68 fach tool adaptor HSK 40E Rbjdjxfb E Ajpfx Adbst turning speeds 30.000 U/min fixed table - dimensions 300 x 400 mm mm workpiece weight 200 kg pallet table size 320 x 320 mm feed speeds autom. x/y/z 40 m/min. spindle drive motor 13 kW Number of working hours 32369 h total power requirement 16 kW weight of the machine ca. 7.500 kg High-speed 3-axis universal machining center with 7-station pallet changer. Operating hours: 44,899 hours. Load hours: 32,369 hours. Spindle time since replacement: 13,350 hours. Gantry-style machine with a solid monoblock polymer concrete construction, compact linear ball bearings, Heidenhain direct measuring system, hydraulic power unit for tool and pallet clamping, and digital drives with liquid-cooled Siemens AC servo motors. Accessories: 1 BURN refrigeration unit, 1 Keller L-Cut extraction system (built in 2012), PS 32 setup button, and tool blow-off device. Machine dealer with own stock of 1600 m².

Condition: new, Year of construction: 2025, Universal milling and drilling machine. X 600 mm Y 500 mm Z 450 mm - Heidenhain TNC 620 with ABENE/HEIDENHAIN software for easy operation - 2-stage gearbox, with frequency-controlled spindle motor 55 - 4,000 rpm. Rjdpfei Hqhmex Adbebt - 1 LED machine light 24 V / 70 W - HR-510 electronic handwheel for X, Y and Z axis - Complete electrical equipment for 400 V 3 phases 50 Hz. - Transformer for 24 V control voltage. - All fuses in the electrical cabinet are automatic. - Mechanical longitudinal, transversal and vertical feed - AC motor spindle, 7,5 kW - Spindle for Z axis, diameter 40 mm, ball screw. - Spindle for X and Y axis, with backlash free ball screw. Ø 32 mm. - All guides are hardened and ground. - An automatic central lubrication system lubricates all guides and ball screws. ball screws. - AC servo motors with infinitely variable control by Heidenhain TNC 620. - Chip tray, extendable - Collision protection monitoring in all axes by electronic threshold value monitoring - Keys, operating instructions, spare parts catalog and acceptance protocol. - Mechanical handwheels in all axes (option) - Table enclosure - Key switch to select between manual and automatic mode. We offer you a machine that is ideally suited for education and training. Our machine is characterized by its robust construction and allows precise machining of the workpieces. Thanks to its features, it is ideal for use in the training workshop or in professional training. The machine makes it possible to gain practical experience in CNC manufacturing and to deepen the understanding of CNC technology. Our machine is located in our warehouse in Pfullingen and can be inspected at any time. We would also be happy to allow you to perform a test machining to demonstrate the machine's capabilities. You will quickly discover how easy and efficient our machine is to operate. We offer you the machine at a fair price. Feel free to contact us for more information or to request a quote. We are confident that our machine will meet your requirements and look forward to your inquiry.

Condition: good (used), Year of construction: 2006, 1. TECHNICAL DATA Working area X axis: 400 mm Y axis: 450 mm Z-axis: 350 mm B-axis: +-110 ° C axis: 360 ° Working spindle Speed range: 100 - 42`000 rpm tool holder: HSK E 40 spindle power at 40 % ED: 13 spindle power at 100 % ED: 10 Torque at 60 % ED: 4,25 Torque at 100 % ED: 3,2 Lubrication: oil/air Feed rate Rapid traverse speed: Max. 40 m/min B axis: 150 rpm C axis: 250 rpm Axis acceleration, XYZ: Max. 1g (10 m/s2) B axis: 100 rad/s2 C axis: 300 rad/s2 Tool changer: 68-fold Chip to chip: 12.5 s Rodpfxsx H Ntao Adbobt Tool change time: 10,0 s Work table: 120 mm Max workpiece diameter that can still be rotated 360 °: 230 mm Max. Workpiece height: 350 mm Max. Workpiece weight: 25 kg Hfsbrjigrf Ie Icm Ener Control: Heidenhain iTNC 530 Weight: 5500 kg