Condition: used, Year of construction: 2005, Feed through press Langzauner LZT-OK 70 E SO Year of construction 2005 Serial number 401-05-X077 Maximum press dimensions 3000x1500mm Maximum stroke 400mm Pressure 70T20kW, 31Amp, 380V 6cylinders Top plate 3000x1500mm, electrically heated Base plate 3400x1680mm, not heated With input and output conveyor. Dimensions:12000x2350xH2650mm, weight 6500kg - Year: 2005 Gsdpfx Ajwnh Hzsh Djkf - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 401-05-X077 - Max. workpiece length [mm]: 3000 - Number of cylinders [pcs]: 6 - Total working pressure [ton]: 70 - Heating type: Electric heated Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled Gedpfxewp Rqfe Ah Dokf All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: excellent (used), Throughfeed press 3000 mm 14 top cylinders 6 side cylinders Godpfjx Apxljx Ah Dekf Water heating with heating elements in the plate CE marking Year of manufacture: 1996

Condition: good (used), I sell a pneumatic press. Gkedpfx Ahoun U Uie Dsf

Condition: excellent (used), Catalogue no.: 7815 TECHNICAL DATA Worktable dimensions (L/W): 2900x1200mm Overall table dimensions: 3000x1300mm Operating temperature: ±40-60°C Maximum temperature: ±60°C Total machine power: 5.25kW Vacuum pump power: 0.90kW Vacuum pump capacity: approx. 25/30m3/h Gkodpfx Ajxwygcjh Dsf Noise level: approx. 70dB Dimensions (L/W/H): 3060x1400x1400mm Weight: 360kg – DTR Documentation – Unpainted – Very good condition – Used press Net price: 21,900 PLN Net price: 5,200 EUR depending on the exchange rate of 4.2 EUR (Prices may change with higher fluctuations)

Condition: used, Drawer Press ZVB/ ZUB Gedpfx Aex Dkygsh Djkf Dimensions (W x H x D): approx. 250x200x100 cm, with 3 press rams, of which 2 are electrically movable, control cabinet, operating terminal, 1 KUPER glue application unit, 1 drilling unit,

Condition: used, Year of construction: 1990, total width: 2,200 mm, total length: 5,900 mm, total height: 2,880 mm, Empty weight: 3.500 kg Corpuspers OCMAC - KGC EL TA Max. enclosure dimension 2450x1450x900mm Fully equipped with updated controls and cabling! Overall dimensions: 5900x2200x2880mm (LxWxH), weight 3500kg - Year: 1990 - Documentation available: No - CE certificate present: No - Serial number: 0307 - Max. workpiece length [mm]: 2450 - Max. workpiece width [mm]: 1450 Gjdpfx Aswng T Hsh Dskf - Max. workpiece height [mm]: 900 - Transport dimensions: 5900mm x 2200mm x 2880mm (l x w x h) - Transport weight [kg]: 3500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: new, Year of construction: 2026, The Concept Eco and Concept Primus are the ideal assembly support for dowel construction at the case goods as well as drawer production. Gkodpsdx R Dmefx Ah Djf Short introduction: • With workpiece tolerance compensation (System GANNOMAT) • 2 Potentiometer for stepless adjustable pressing force • Pressing force min. 300/500 daN (kg) at Concept Eco resp. Pressing force min. 600/800 daN (kg) at Concept Primus • Pressing force max. 2200 daN (kg) at Concept Eco resp. Pressing force max. 3500 daN (kg) at Concept Primus • 3 Pressing velocities and adjustment rates 5 /10 / 25 mm/sec. (with fine positioning / creep feed) • Adjustable clamping cycle time with automatic opening • Simple operation by 6 individual push buttons for 8 motion sequences

Condition: excellent (used), functionality: fully functional, Description of the device Godpfx Aovy Uqfoh Dokf Pump motor power - 1.35 kW 10 hydraulic cylinders for pressure - spring return 17 upper hydraulic cylinders for pressing the beam Maximum working dimensions 7x1.5m

Condition: good (used), Year of construction: 2000, machine/vehicle number: 2000 53, total length: 3,300 mm, Equipment: hot water, Sergiani 10-deck press Gkedpfx Ahox Ezkzo Dsf continuously maintained and in operation With this press, doors can be loaded one after the other while the pressure on the doors in the other compartments is kept constant.

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, * Wemhöner Basic 1000 Plus - Year of manufacture 2008 - Very good condition, rarely used * Type KT-MB-28/15-240 * With automatic pin system and in-line turner * 2 tables with automatic Vario-Pin system * With Teflon coating for pre-glued foil * Foil laying system for pin table (pre-glued foil) * Heating plate size: 2800 x 1500mm * Max. workpiece size: 2,540 x 1,250mm * Membrane: yes * Cutting station * Foil carousel storage, 3.2m height with 14 suspension rods * PLC control Siemens S7 * Control unit for PLC SIEMENS TP 270 (Touchscreen) Gkjdpfx Ajxbcudjh Def * Automatic membrane tensioning * Installed power supply: 38.5 kW * Max. chamber pressure: 6 bar * Max. press opening: 150mm * 6 cylinders with Ø 125mm * Operating voltage: 400V 50/60Hz * Chamber height: 40/60mm * Max. pressing force: 2400 kN * Hydraulic system operating pressure: 320 bar

Year of construction: 2003, condition: used, Drawer press ZUB / ZVB Central Fixture Construction. Used. Dimensions (W x H x D): approx. 220x210x110 cm, with 4 pressing units, electrically movable, 1 control cabinet, operator terminal. Gjdpfex Dkw Sox Ah Dskf

Condition: used, Price: On request Veneer press Feed-through press HOT Colombo Machine dimensions: 4400x1400 Oil heated input/output is included 8 cylinders Complete with glue roller etc. - Documentation available: No - CE certificate present: No - Number of stages [pcs]: 1 - Number of cylinders [pcs]: 8 - Heating type: Oil heated Gksdpfxswnhvvs Ah Djf Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: new, Year of construction: 2026, The composition of the cabinet handling systems to create a manual, semi- or fully-automatic cabinet assembly line is depending on individual production requirements. Gedodx R D Dopfx Ah Dskf Cabinet assembly lines that will make work easier, reduce set-up time and increase precision, we will explain to you in a personal conversation.

Condition: like new (used), Year of construction: 2019, functionality: fully functional, feed length X-axis: 3,000 mm, feed length Y-axis: 1,500 mm, Lightly used ORMA MEMBRANE PRESS, model DUPLEX 30/15 vacuum press with preheating oven/table for acrylic and thermoform plastics. Has only seen occasional light project use. Suitable, for example, for processing Corian sheets. An alternative to buying a new machine. Pressing area: 3000 x 1500 mm Vacuum pressing force across the entire work area: 44 tons 11 tons/m2 Maximum pressing height: 500 mm ORMA HEATING OVEN/TABLE 30/15 FOR ACRYLICS AND THERMOFORM PLASTICS • Heating by electric resistors and air circulation • Heated area: 3000 x 1500 mm • Max height of workpiece: 100 mm • Heating power: 18 kW • Maximum temperature: 200°C • Digital temperature control from the control panel The unit's frame is made from welded thick steel beam structure and welded steel sheets. There is an insulation layer between the galvanized steel sheets of the oven’s inner and outer surfaces. Manual oven opening, guided rails, and transport wheels. Membrane press bed is phenolic-coated plywood featuring a grid pattern for improved vacuum distribution. The top section, where the membrane film is mounted, opens 45 degrees and is equipped with gas springs. Quick and easy upper section locking. Manual membrane film quick-mount system. Vacuum system with a single 25 m3/h vacuum pump. Control panel, installed on the left side of the machine, includes: • Main switch • Control voltage indicator lamp • Emergency Stop button • Temperature monitoring/control • Vacuum pump status light on/off Gkedexz Rhfepfx Ah Dof • Heater status light on/off

Condition: used, Year of construction: 2003, Working height: 2300 mm, Working width: 3500 mm, Motor: 1.5 kW, 3 pressure cylinders from above, 2 from the side, Pressure per cylinder: 3000 kg, Cylinder stroke: up to 200 mm, Hydraulics: 10-150 bar, Space required: 3950 x 900 x 2550 mm, Weight: 670 kg Storage location: Nattheim Gkedpovvkmbefx Ah Dsf

Condition: good (used), Year of construction: 2000, functionality: fully functional, The frame press is in excellent condition, having been professionally and meticulously maintained. The machine presses precisely at an angle and delivers high pressing force. 3 vertical and 2 horizontal hydraulic cylinders, including press unit for angled components Pressing force is finely adjustable Press width: 3450 mm, height: 2250 mm Length: 4350 mm, height: 3000 mm, depth: 800 mm Further information available via email or phone. Private sale, therefore no returns, no warranty, and no liability. Sale is made under exclusion of any liability. No shipping. Gkedpfx Ahoxgn E Sj Dsf

Condition: used, Veneer press OTT Type JU 60S Pressing area max. 225x120 cm Gkedpfx Ajvdaymeh Def Electric

Condition: good (used), Good condition. 3 t/h. 200 kW engine. Gedpfx Ahexzi Ane Dekf

Condition: new, Year of construction: 2026, The Concept Eco and Concept Primus are the ideal assembly support for dowel construction at the case goods as well as drawer production. Short introduction: • With workpiece tolerance compensation (System GANNOMAT) Gjdjdx R Dtepfx Ah Dekf • 2 Potentiometer for stepless adjustable pressing force • Pressing force min. 300/500 daN (kg) at Concept Eco resp. Pressing force min. 600/800 daN (kg) at Concept Primus • Pressing force max. 2200 daN (kg) at Concept Eco resp. Pressing force max. 3500 daN (kg) at Concept Primus • 3 Pressing velocities and adjustment rates 5 /10 / 25 mm/sec. (with fine positioning / creep feed) • Adjustable clamping cycle time with automatic opening • Simple operation by 6 individual push buttons for 8 motion sequences

Condition: used, Technical data: Godpfexzrt Ajx Ah Dekf Number of pistons: 4 Piston diameter: 45 mm Connection to central heating: NO Shelf dimensions: 2500x1200 mm Clearance: 460 mm Hydraulic pressing Motor power: 2 kW Power supply: 380 V Overall dimensions: Length: 2900 mm Width: 1370 mm Height: 2150 mm

Condition: used, Year of construction: 1992, Dimensions: 5700 x 1300 x 2400 mm Storage location: Nattheim Gjdpfxevvkl Ds Ah Dskf

Condition: used, Year of construction: 1994, Frame press Schafberger & Sprödhuber Type Super 4 Kw 3 m x 6 m Gkjdjilurnepfx Ah Dof

Condition: new, Year of construction: 2025, The Concept Easy is the ideal assembly support for dowel construction at the case goods production as well as at drawer production. Short introduction: • Small footprint requirement, less than 1,8 m2 • Potentiometer for stepless adjustable pressing force Gedpfx Ajdx Daash Dskf • Pressing force min. 300 daN (kg) • Pressing force max. 2200 daN (kg) • 3 Pressing velocities and adjustment rates 5 /10 / 25 mm/sec. (with fine positioning / creep feed) • Adjustable clamping cycle time with automatic opening

Condition: used, Technical specifications: Briquette diameter: 60 mm Briquette length: 50 mm Hopper diameter: 1100 mm Hopper height: 910 mm Hopper capacity: 0.89 m³ Throughput: 60-80 kg/h Power supply: 400 V Motor power: 7.5 kW Safety switch Overall dimensions: Gjdpoxzqmzofx Ah Djkf Length: 1670 mm Width: 1100 mm Height: 1500 mm