Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Bsdjzvq Rcopfx Andodi Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price: 35 000 EUR (VAT is not included)

Condition: used, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, planing width: 520 mm, number of blades: 4, total width: 1,100 mm, total height: 1,200 mm, overall weight: 600 kg, – Made in Italy – In very good condition TECHNICAL SPECIFICATIONS: – Planing width: 520 mm – Planning height: 240 mm – Main motor: 5.5 kW – Electric height adjustment – Four feed speed settings – Four TERSA knives – Shaft diameter: 110 mm – Shaft speed: 4500 RPM Bjdpe Agfhqefx Andodi – Segmented, helical toothed infeed shaft – Rubber-covered outfeed shaft – Nozzle diameter: 150 mm – Dimensions (L/W/H): 120x110x125 – Weight: ~600 kg

Condition: excellent (used), CATALOGUE NUMBER 7611 Technical specifications: - inlet dimensions: 460x180mm - outlet diameter: 300mm - roller width: 550mm - roller diameter: 350mm - number of blades: 10 pcs - blades arranged in 2 rows - automatic reversing - blade setting device - screen diameter: 30mm - top and bottom conveyor belt - lower drive roller - length of the feed conveyor belt: 4400mm - main motor: 37kW - top feed motor: 1.5kW - bottom feed motor: 2.2kW - dimensions (L/W/H): 6100x1150x1000mm - weight: approximately 3500kg ADVANTAGES - Made in Germany - Automatic reversing - Top and bottom conveyor belt - Blade setting device - Very good condition - Used shredder Bjdpfj Af Uvcsx Andedi Net price: 98,900 PLN Net price: 23,000 EUR Net price calculated based on an exchange rate of 4.30 PLN/EUR (the price may be subject to change in the event of significant exchange rate fluctuations)

Condition: excellent (used), CATALOGUE NUMBER 8035 TECHNICAL DATA - shaft width 640mm - 4-knife shaft - max. thickness of workpiece on thicknesser 250mm - max. thickness of workpiece on side heads (3-sided) 110mm – from above: - ejectors - geared infeed shaft - pressure roller - planing shaft Bdedpfxezu Sgps Andji - pressure roller - smooth outfeed shaft - pressure roller at the outlet – from below: - guide strip - adjustable rollers in the lower bed 2 pcs – from the rear: - side spindles + pressure roller 2 pcs - spindle height 110mm - spindle diameter 30mm - spindles adjustable left/right, up/down - motors for side spindles 2x4kW - main motor 7.5kW - 3 feed speed types - electric table lifting - dust extraction nozzle 2x110mm - overall dimensions L/W/H 1650x1500x1210mm - weight 1370kg ADVANTAGES - Made in Poland - Shaft with 4 knives - Used planer, very good condition Net price: 23900 PLN Net price: 5558 EUR depending on the exchange rate of 4.30 EUR (Prices may vary due to higher fluctuations)

Condition: used, Year of construction: 2022, PANEL SAW WITH TILTING SAW BLADE Linvincibile SI 5 KEY FEATURES SLIDING TABLE: GUARANTEED SUPERIOR CUTTING QUALITY OVER THE LONG TERM TELESCOPIC ARM: AN “UNBEATABLE” SMOOTH MOVEMENT SAW UNIT: FOR A PERFECT CUT Technical Data SI 5 Main saw blade diameter (mm): 550 Cutting capacity with extendable fence - with table 3200 mm - with table 3800 mm 3200x3200 3800x3200 Saw blade tilt (degrees): 46 Max. cutting height at 90° (mm): 200 Max. cutting height at 45° (mm): 130 Saw blade speed (rpm): 2500-3500-5000 Scoring blade speed (rpm): 8500 - Extractor port diameter: - on frame - on blade guard 120 100 Main motor power [S6 -40%] Hz50 kW: 7 Scoring motor power [S6 -40%] Hz50 kW: 0.9 Cutting width at rip fence (mm): 1600 Standard equipment and accessories - Optimizer/Process control app for tablets: SCM Thundercut. The app can be downloaded from the App Store or Play Store for tablets compatible with iPadOS or Android. It can be activated via the QR code supplied with the machine. The app enables: * Management of machine fleet and material/panel storage * Creation and editing of projects, importing projects from main furniture design software (file format "cpout"), importing cutting lists * Optimization of cutting lists by selecting one or more proposals from the optimization software integrated into the app * Correct machine settings for each cut, thanks to the simple and intuitive graphics of the 3D sequencer, guiding the operator step by step * Printing barcode labels to identify the various parts, via Bluetooth connection with compatible label printers. - 10-year warranty on the sliding table guide system - Sliding carriage entirely made of aluminum structure with guidance on crimped, hardened and arc-ground steel rails with large contact area - Max. saw blade diameter* up to 450mm with scoring blade mounted* up to 550mm without scoring blade - eye-S 15" electronic control including: * 15" touchscreen monitor * Direct control of the following working axes with manual, semi-automatic, automatic, and incremental modes: - Height adjustment of the main saw blade - Tilt adjustment of the saw unit - Rip fence adjustment - Height and lateral adjustment of the scorer (the scorer is automatically raised to the set position on activation and lowered on deactivation) * Operator assistance functions for complex cuts * Ability to store up to 1000 programs with associated image * Ability to store up to 1000 different tools with associated image * Cutting process management of preloaded parametric machining programs * Environment for creating and storing new sequenced working programs * Automatic import of working dimensions from Thundercut app * USB port * Ready for network connection - Auxiliary function of the electronic control, including: * Determination of correct fence position on rip fence for format processing with tilted saw blade * Determination of correct fence position on rip fence for angle cuts with mitre fence on the work table with or without tilted saw blade - Pivoting control panel above the table - Scoring unit with independent Bodpfx Asz Hb Nbsndodi

Condition: ready for operation (used), Year of construction: 1982, functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS GENERAL DATA Manufacturer: Panhans Type: 608/1.8 Year of manufacture: 1982 Machine number: 202 SAWING UNIT Saw blade diameter: 350 mm WORK TABLE Table dimensions: 1,200 × 1,000 mm Bdodpfo Adu Dmjx Andei ELECTRICAL DATA Operating voltage: 380 V Frequency: 50 Hz Rated current: 11.5 A MACHINE DETAILS DIMENSIONS AND WEIGHT Length: 2,400 mm Width: 1,200 mm Height: 1,500 mm Weight: 500 kg

Condition: used, Year of construction: 2020, functionality: fully functional, empty load weight: 385 kg, load capacity: 2,000 kg, construction width: 980 mm, Rotating device Load center of gravity: 500 ISO class: ISO Class 2 = 1,000 - 2,500 kg Bdjdpfx Anoz Ev E Iedei Condition: Ready for use and fully functional Technical condition: very good

Condition: excellent (used), CATALOGUE NUMBER: 7480 Technical data: - track width: 360mm - shaft width: 350mm - max. disc diameter: 350mm - disc bore diameter: 80mm - max. cutting height: 120mm - table dimensions: 2040x1220mm From above: - pawls - toothed feed shaft - pawls - saw shaft - sliding, pressure shaft From below: - rollers in front of the table, 2 pcs - guide - pawls - track - central track lubrication - electric saw shaft lifting - electric body lifting - stepless feed speed adjustment - dust extraction nozzle diameter: 140mm, 160mm - main motor: 30kW - overall dimensions (L/W/H): 2600x2300x1850mm - weight: approx. 4000kg ADVANTAGES – Czech production Bdeds Agur Nspfx Andji – used multi-blade saw – very good condition Net price: 30900 PLN Net price: 7190 EUR, depending on the exchange rate of 4.30 EUR (Prices are subject to change due to significant fluctuations)

Condition: used, Year of construction: 1993, Number of spindles 6 St. Working width 230 mm Working height 160 mm Feed motor 4 kW Dimensions (L/W/H) 4400 x 1800 x 1500 mm WEINIG Unimat 23 Automatic Planing and Grooving Machine For sale on behalf of a customer customer is still working on it, machine can be visited ----- Manufacturer’s Technical Specifications: Working width: 20–230 mm Working height: 6–160 mm Number of spindles: 6 Motor power per spindle: 5.5 kW (7.5 PS) Feed motor power: 4.0 kW (5.5 PS) Spindle speed: 6,000 rpm 3 units, table rollers ----- ----- Planing table length: 2 m 1 adjustment gauge 2 planing heads, 240 mm 3 brake units are defective; these could be reinstalled by an electrician. ----- Bsdpjzz Ai Ujfx Andjdi Additional technical data (former order confirmation) attached ----- Price of the above-mentioned machine upon request! ----- (Technical specifications according to the manufacturer—not guaranteed!) All prices listed are net, plus applicable sales tax.

Condition: new, Year of construction: 2026, Specifications Working area: X 2100mm Y 3100 mm, X 2100mm Y 4100 mm Z-axis range: 300 mm Table type: slatted, vacuum Vacuum sections: 6 manually controlled sections Drives: 1.5 kW Servo AC Ethercat Travel speed: up to 40 m/min Control system: Industrial controller, Ethercat communication with remote access Electro-spindle set: 9 kW Tool clamping: ISO30 collet Tool magazine: 12 positions Tool length sensor: YES Positioning bases: 5 pcs Dust extraction foot: with outlet for connecting a dust extraction system/vacuum cleaner Manipulator: manual, wired Cooling mist: YES Central oil lubrication: YES CAD/CAM software: YES Access enclosure: including a laser safety curtain Additional options: Vacuum pump or side-channel blower Different electro-spindle powers Different working table size Push-and-dust extraction bar Revolver magazine Oscillating knife head 4th axis, angular heads Drilling units Bdsdpfe Ahiblex Andji

Condition: excellent (used), CATALOGUE NUMBER 6901 TECHNICAL DATA - Max. turning length: 1200 mm - Max. turning diameter: 210 mm - Max. turning diameter with standard support: 90 mm - Max. dimensions of square material for turning with automatic feed: 100 mm - 3 hydraulic copying units - Additional 3 cutting tools on hydraulic pistons (2 installed) - 4 types of spindle speeds - Automatic or manual machine operation - Spindle motor: 9 kW - Hydraulic pump motor: 3 kW - Diameter of extraction port: 90 mm - Dimensions for transport (L/W/H): 3700x2100x2000 mm - Weight: approximately 3000 kg Bdodpezu R S Rsfx Andoi ADVANTAGES - Made in Italy - Automatic hydraulic copying unit - Original DTR documentation - Unpainted - Used lathe, very good condition Net price: 57,900 PLN Net price: 13,465 EUR Net price calculated using an exchange rate of 4.30 PLN/EUR (price may change in the event of significant exchange rate fluctuations)

Condition: new, CATALOGUE NUMBER RE041 Bodj Aggdzspfx Andsdi - new machine TECHNICAL DATA - saw blade diameter ⌀250 – 350/30 mm - scoring blade diameter (only works with ⌀300, 350 mm blades) ⌀120/20 mm - main motor power 4 kW - scoring motor power 0.75 kW - rotational speed 4000 rpm - scoring blade rotational speed 8800 rpm - blade tilt 0 – 45° - max. cutting length 2000 mm - cutting width with parallel fence 1250 mm - splitter ⌀350 mm - spindle flange diameter 87.5 mm - table fence adjustable to 90° – 45° angle, accuracy ±1° - max. cutting height with ⌀300 mm blade 95 mm - max. cutting height with ⌀350 mm blade 120 mm - upper dust extraction port diameter ⌀80 mm - lower dust extraction port diameter ⌀100 mm - weight 620 kg - dimensions of folded machine (length/width/height) 2255x3460x1450 mm Net price: 19900 PLN Net price: 4628 EUR Net price calculated based on the exchange rate of 4.30 PLN/EUR (price may change in case of significant exchange rate fluctuations)

Condition: excellent (used), CATALOGUE NUMBER 7613 Technical data: - inlet width 650mm - inlet height 300mm - shaft width 660mm - blade length 660mm - number of blades 2 pcs - screen dimensions 90x100mm - 2 toothed pull shafts from below - lower shaft motor 3kW - 2 toothed pull shafts from above - upper shaft motor 3kW - belt conveyor - belt conveyor length 2700mm - belt conveyor width 630mm - main motor 75kW - auto-reverse - reverse gear - overall dimensions (L/W/H) 5350x1300x1300mm - weight 4200kg Bsdpfe Af In Uox Andedi ADVANTAGES – Made in Italy – Auto-reverse (adjustable) – Reverse gear – Used shredder, very good condition Net price: 149900 PLN Net price: 34860 EUR, depending on the exchange rate of 4.30 EUR (Prices may vary due to significant exchange rate fluctuations)

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS Swing diameter: 225 mm Turning length: 1,000 mm Diameter over carriage: 1,000 mm Feed rate, continuously variable: 9–400 mm/min Feed rate, continuously variable: 4.5–200 mm/min Travel of steady rest: 360 mm Travel of upper steady rest: 220 mm Bdedpfs Ad Ezcjx Andji Tailstock diameter: 60 mm Tailstock travel: 170 mm Tailstock adjustment: ± 20 mm Spindle speed: 225–2,000 min⁻¹ MACHINE DETAILS Manufacturer: Zimmermann Type: DZUE 1000 Year of manufacture: 1990 Machine length: 2,500 mm Machine width: 1,000 mm Machine height: 1,600 mm Machine weight: 1,000 kg

Condition: excellent (used), Year of construction: 2011, CATALOGUE NUMBER 8016 TECHNICAL DATA - Range of diameters of processed pins: 60-160mm - Max. diameter of input material: 210mm - Min. length of input material: 1000mm - Max. allowance for machining per side: 30mm - Fitted sleeve with a diameter of 90mm - Cutting head drive motor: 22kW - Smooth feed speed adjustment + forward/reverse via frequency inverter - Feed motor: 1.5kW In sequence: - Infeed trough - Toothed pull rollers: 6 pcs - 4-knife cutting head - Smooth pull rollers: 6 pcs - Includes 10 sleeves - Dimensions (L/W/H): 2800x1300x2150mm - Weight: approximately 2200kg ADVANTAGES – Manufactured by the Polish brand SAFO – DTR+CE documentation included Bsdpfx Aj Af Uvnondodi – Includes sleeves – Used turning machine, very good condition Net price: 98,900 PLN Net price: 23,000 EUR, depending on the exchange rate of 4.30 EUR (Prices may vary due to higher fluctuations)

Condition: excellent (used), Catalog number 8036 TECHNICAL DATA max. width of the workpiece 1100 mm max. height of the workpiece 170 mm 2 units: – from above: rubber roller, pressure roller, knurled 1) metal roller, knurled, for calibrating rubber roller, pressure roller 2) rubber roller, knurled + sequential shoe + metal roller rubber roller, pressure roller total power of the units 15 kW – from below: 2 rubber rollers, slip conveyor belt 2 rubber rollers, slip potentiometer for grinding thickness belt blowing pneumatic belt oscillation with photoelectric sensors electric table lifting + manual (for precise adjustment) 2 types of feed speed 0.3 kW with pneumatic brake operating pressure 6-8 bar diameter of the dust extraction nozzle 2x140 mm overall dimensions L/W/H 1840x1650x2000 mm weight 1160 kg – unpainted – made in Italy – automatic shoe – 2 units – potentiometer for grinding thickness Bdedpfx Ane Af Uubsdji – DTR documentation – used grinder, very good condition Net price: 48900 PLN Net price: 11372 EUR, depending on the exchange rate of 4.30 EUR (Prices are subject to change due to higher fluctuations)

Condition: used, Year of construction: 1999, CNC machining center Manufacturer: Homag Type: BAZ 31/60/K Optimat Year of manufacture: 1999 Technical data - Workpiece length max. 6600 mm with single workpiece placement max. 2700 mm with alternating workpiece placement - Workpiece width max. 1200 mm - Workpiece thickness with edge max. 60 mm without edge max. 60 mm with standard clamp without edge max. 120 mm with clamping template when chamfer milling min. 12 mm when radius milling min. 2x radius + 10 mm - Working height, lower edge of workpiece 950 mm - 2 vacuum pumps, each with 66/100 m3/h for clamping system Main spindle 12 kW, water-cooled - for HSK F63 - Three-phase asynchronous motor 12 kW at S1, 600 Hz - Speed range: 1500 - 18000 rpm Bsdo Ahmz Djpfx Andedi - Tool weight max. 6 kg incl. tool holder Tool changer, 12 positions - for tools and aggregates with HSK F63 - 12 x diameter max. 130 mm or - 6 x diameter max. 180 mm and 6 x diameter max. 70 mm - Tool diameter for grinding tools max. 200 mm Aggregate interface BAZ for main spindle For accommodating the machining and gluing aggregates with integrated pneumatic-electrical-electronic supply and pivoting drive, C-axis. Swiveling range without limitation. Hose-free compressed air supply. Drilling head with 17 spindles - 1 motor 1.9 kW, frequency-controlled - Speed selectable via program 4500/6500 or 8000 rpm - Each spindle can be activated individually - Arrangement of spindles in T-shape. - 11 spindles in X-direction, 7 spindles in Y-direction Homatic control system CNC programming system WOODWOP Postprocessor Programming based on CNC drawing Laser positioning aid for vacuum clamping system Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, functionality: fully functional, Dust extraction nozzle for a four-sided planer Number of connections: 9 Connection diameter: 140 mm Bdsdpfx As Agrzlondei Main duct diameter: 450 mm This nozzle is compatible with a Weinig Hydromat planer:

Condition: excellent (used), CATALOGUE NUMBER: 6950 TECHNICAL DATA - Max. width of workpiece: 220mm - Max. height of workpiece: 130mm - 4 spindles: 1) Horizontal lower spindle, 220mm, 5.5kW 2) Vertical right spindle, 130mm 3) Vertical left spindle, 130mm; (2 and 3 spindles) 5.5kW 4) Horizontal upper spindle, 220mm, 5.5kW - 4 spindles with electric up/down adjustment - All spindles adjustable up/down, left/right - Spindle diameter: 40mm - 4 top feeding rollers, toothed, including 1 double roller - 1 top double roller for withdrawal, rubber - 1 bottom roller for withdrawal, rubber - Feed via cardan shafts - Smooth feed rate adjustment: 6-22 m/min - Feed motor: 2.2kW - Lifting motor: 0.55kW - Electric adjustment of planing thickness - Length of infeed table: 1970mm - Central lubrication - Diameter of dust extraction nozzle: 3x120mm, 140mm - Enclosed in a cabinet - Dimensions (L/W/H): 3350x1400x1400mm, weight: 1700kg - Made in Germany - Unpainted - Used planer, very good condition Net price: 29900 PLN Net price: 6953 EUR Net price calculated based on an exchange rate of 4.30 PLN/EUR Bdedozwwliopfx Andsi (Price may be subject to change in case of significant exchange rate fluctuations)

Condition: good (used), functionality: fully functional, For sale is a used, custom-built box-clamping machine for the production and assembly of wooden boxes. The system is equipped with a total of 6 hand-operated clamping devices from the Senco brand. The clamping devices are activated via foot valves, allowing the box parts to be positioned and clamped together during the work process. Particularly suitable for the production of wine boxes, fruit boxes, vegetable boxes, and other wooden packaging. Technical data / equipment: Manufacturer: Custom-built Machine type: Box-clamping machine / Box assembly machine 6 hand-operated clamping devices Bdodpozynf Ssfx Andoi Clamping device manufacturer: Senco Activation via foot valves Pneumatic operation For clamping box parts together Workpiece support / workbench Adjustable fixture for different box dimensions Robust frame construction Suitable for: Wine boxes Fruit boxes Vegetable boxes Packaging boxes other wooden boxes and wooden packaging The machine is in used condition. Equipment and condition as shown in the photos. Transport is possible for an additional charge! The machine is currently still at the customer's site but would be available shortly. The machine will be inspected before sale. For used machines with a year of manufacture of 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale, and changes are subject to change. All information is without guarantee.

Condition: used, Year of construction: 1991, functionality: fully functional, overall weight: 1,400 kg, fuel type: electric, – year of manufacture: 1991 – made in Germany TECHNICAL SPECIFICATIONS: – hopper dimensions (length / width): 1800 x 1600 mm – rotor diameter: 200 mm – rotor length: 800 mm – main motor power: 15 kW – hydraulic pump motor power: 0.75 kW – number of knives: 18 pcs – rotating cutting knives with dimensions: 30 x 30 mm – screen: ø 12 and 17 mm Bdodpfxe Afc Sbo Andei – AUTO REVERSE – hydraulic drawer – height of hydraulic drawer: 175 mm – diameter of discharge outlet: 200 mm Machine dimensions: – length: 210 cm – width: 170 cm – height: 185 cm – weight: ~1400 kg

Condition: used, Year of construction: 1988, Used Machine Year of manufacture: 1988 Features and technical specifications: - Table size: 2000 x 880 mm (entire table made of cast iron) - With extendable frame support - Drive motor, pole-changing, 5/6 kW - Spindle speeds: 3000/4500/6000/9000 rpm Bjdpfx As Agw S Aendjdi - Milling spindle height adjustment: 110 mm - Milling spindle tilt: 45° - With Holz Her 3-roller feed unit

Condition: used, CATALOGUE NUMBER: 7650 Technical data: - max. working length: 1500mm - max. working diameter: 250mm - milling (disc milling cutter): 7.5kW - spindle – 2800 rpm, 3kW - spindle speed: 700/1200/1500/2000 rpm - grinding unit: 0.75kW - hydraulic motor: 3kW - total power: 17.75kW - air consumption: 6-8 bar - infeed for square stock up to 150x150mm - dust extraction port diameter: 100mm, 160mm - transport dimensions (L/W/H): 4350x2300x1980mm - weight: approx. 3000kg ADVANTAGES: - manufactured in Germany Bdsdpfxoztrfcs Andei - automatic hydraulic copying device - original technical documentation - unpainted - used lathe, very good condition Net price: 59900 PLN Net price: 13930 EUR Net price calculated based on an exchange rate of 4.30 PLN/EUR (price may change in case of significant exchange rate fluctuations)

Condition: like new (used), Year of construction: 2025, COLUMBUS MOVE – The space-saving professional vacuum press for maximum flexibility Full performance. Minimal space requirements. Bdedpfj Afxvzox Andsi The COLUMBUS MOVE was specifically developed for operations wishing to work professionally with vacuum technology—even with limited space available. Thanks to its mobile and compact design, the press can be easily stored after use, freeing up valuable workshop space. Ideal for: * Veneering * Laminating/form gluing * Coating * Curved workpieces * Flexible custom production Your benefits: * Space-saving MOVE system * Mobile and flexible use * Heavy-duty industrial construction * Lifetime guarantee on the machine structure * Premium BECKER vacuum pump * Quick-change membrane system * Connection for external vacuum bag * Simple operation and high operational safety COLUMBUS 360° included: With a practical manual, Master Manual, and AI support, you benefit not only from state-of-the-art technology but also from decades of application expertise. Technical specifications: * Usable area: 3050 x 1350 mm * Maximum payload: 1.0 t * Maximum workpiece height: 600 mm * Vacuum pump: BECKER 40 m³ * Weight: 670 kg Particularly attractive for companies seeking flexible production while making efficient use of valuable workshop space. COLUMBUS has been developing professional vacuum technology for woodworking operations for nearly 50 years. Viewing and personal consultation gladly by appointment.

Condition: excellent (used), Catalog number: 7502 TECHNICAL DATA Infeed carriage DTBC-P Wheelbase 750mm Diameter of the infeed material 100-800mm Total side travel 160mm Log rotation to the left and right 360 degrees Bdsdpj Af Uyvofx Andsi Forward and reverse travel speed variable Hydraulic pump motor power 5.5kW Auxiliary carriage DTCB Wheelbase 750mm Side travel range 160mm Log rotation to the left and right 360 degrees Side travel motor power 1.1kW Infeed carriage dimensions (L/W/H) 2850/1400/1500mm Auxiliary carriage dimensions (L/W/H) 950/650/750mm Total weight 1450kg ADVANTAGES – Made in Poland – Robust construction – Includes cables and chains – Used machine, very good condition, after a major overhaul (invoice available for inspection) PRODUCT FEATURES The auxiliary carriage is designed to support logs or stacks from the infeed side of the saw, with a diameter range of 100 mm to 750 mm. The infeed carriage is designed to feed logs and stacks to the saws, with a diameter range of 100 mm to 750 mm. The device for manipulating logs, namely for clamping the log in the clamps, performing transverse movement, and rotating the log, is powered by hydraulic drives. Net price: 59900 PLN Net price: 13930 EUR, depending on the exchange rate of 4.30 EUR (Prices are subject to change due to significant fluctuations) * MAR-MASZ guarantees the quality of your purchase, but is not an authorized representative of the manufacturer. All trademarks and names are used for informational purposes only, to identify the product. We only resell products that the manufacturer has previously introduced to the market. We have no business ties with the manufacturer.